Datasheet

208
ATmega323(L)
1457E–11/01
Note: 1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at Vcc = 5V, 10mA at Vcc = 3V) under steady state
conditions (non-transient), the following must be observed – PDIP Package:
1] The sum of all IOL, for all ports, should not exceed 200 mA.
2] The sum of all IOL, for port A0-A7, should not exceed 100 mA.
3] The sum of all IOL, for ports B0-B7,C0-C7, D0-D7 and XTAL2, should not exceed 100 mA – TQFP Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0-A7, should not exceed 100 mA.
3] The sum of all IOL, for ports B0-B3, should not exceed 100 mA.
4] The sum of all IOL, for ports B4-B7, should not exceed 100 mA.
5] The sum of all IOL, for ports C0-C3, should not exceed 100 mA.
6] The sum of all IOL, for ports C4-C7, should not exceed 100 mA.
7] The sum of all IOL, for ports D0-D3 and XTAL2, should not exceed 100 mA.
8] The sum of all IOL, for ports D4-D7, should not exceed 100 mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (3mA at Vcc = 5V, 1.5mA at Vcc = 3V) under steady state
conditions (non-transient), the following must be observed – PDIP Package:
1] The sum of all IOH, for all ports, should not exceed 200 mA.
2] The sum of all IOH, for port A0-A7, should not exceed 100 mA.
3] The sum of all IOH, for ports B0-B7,C0-C7, D0-D7 and XTAL2, should not exceed 100 mA – TQFP Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports A0-A7, should not exceed 100 mA.
3] The sum of all IOH, for ports B0-B3, should not exceed 100 mA.
4] The sum of all IOH, for ports B4-B7, should not exceed 100 mA.
5] The sum of all IOH, for ports C0-C3, should not exceed 100 mA.
6] The sum of all IOH, for ports C4-C7, should not exceed 100 mA.
7] The sum of all IOH, for ports D0-D3 and XTAL2, should not exceed 100 mA.
8] The sum of all IOH, for ports D4-D7, should not exceed 100 mA
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum V
CC
for Power-down is 2.5V.
I
CC
Power Supply Current
Active 4 MHz, V
CC
= 3V
(ATmega323L)
5mA
Active 8 MHz, V
CC
= 5V
(ATmega323)
15 mA
Idle 4 MHz, V
CC
= 3V
(ATmega323L)
2.5 mA
Idle 8 MHz, V
CC
= 5V
(ATmega323)
8mA
Power-down mode
(5)
WDT enabled, V
CC
= 3V 9 15.0 µA
WDT disabled, V
CC
= 3V <1 4.0 µA
V
ACIO
Analog Comparator
Input Offset Voltage
V
CC
= 5V
V
in
= V
CC
/2
40 mV
I
ACLK
Analog Comparator
Input Leakage Current
V
CC
= 5V
V
in
= V
CC
/2
-50 50 nA
t
ACID
Analog Comparator
Initialization Delay
V
CC
= 2.7V
V
CC
= 4.0V
750
500
ns
DC Characteristics (Continued)
T
A
= -40°C to 85°C, V
CC
= 2.7V to 5.5V (Unless Otherwise Noted)
Symbol Parameter Condition Min Typ Max Units