Datasheet

44
SAM9260 [SUMMARY]
6221LS–ATARM–15-Oct-12
6221FS All new information in Section 7.2.1 ”Matrix Masters”, Table 7-1, “List of Bus Matrix Masters,”
on page 16 and Section 7.2.3 ”Master to Slave Access”, Table 7-3, “SAM9260 Masters to
Slaves Access,” on page 16.
4457
In Figure 2-1 ”SAM9260 Block Diagram” on page 3, updated EBI signals NRD, NWR0, NWR1,
NWR3.
4431
Added details on Timer/Counter blocks in Section 10.4.5 “Timer Counter” on page 35. 4369
Updated Chip ID in Section 9.12 “Chip Identification” on page 28. 4582
6221ES Updated information on programmable pull-up resistor in Section 6.4 “PIO Controllers” on page
13.
3972
Updated Section 6.7 “Slow Clock Selection” on page 14.
In Table 10-1, “SAM9260 Peripheral Identifiers,” on page 29, added Note on clocking and
corrected Peripheral Name for PID12, PID13 and PID14.
3504 and
3543
Placed comment on RDY/BUSY with PC13 in Table 10-4, “Multiplexing on PIO Controller C,”
on page 33.
3406
6221DS Removed references to VDDOSC in “Features” , in Table 3-1, “Signal Description List”, and in
Section 5.1 “Power Supplies” on page 12. Corrected VDDPLLA and VDDPLLB with VDDPLL
and GNDPLLA and GNDPLLB with GNDPLL in Table 4-1, “Pinout for 208-pin PQFP Package,”
on page 10 and in Table 4-2, “Pinout for 217-ball LFBGA Package,” on page 11.
3183
In Figure 2-1 on page 3, corrected range for SCKx pins; label change on matrix block.
3235,
3071
In Figure 2-1 on page 3 and Section 7.3 “Peripheral DMA Controller” on page 17, removed TWI
PDC channels.
3066
In Section 6.3 “Reset Pins” on page 13, added NRST as bidirectional. 3236
In Figure 9-3 on page 27, added UHPCK as USB Clock Controller output. 3237
In Section 10.4.3 “USART” on page 34, added information on modem signals. 3245
6221CS For VDDIOP1, added supported voltage levels in Table 3-1, “Signal Description List,” on
page 4 and corrected supported voltage levels in Section 5.2 “Power Consumption” on page
12.
2874
Removed package marking and updated package outline information in Section 4. “Package
and Pinout” on page 9.
2922
Change to signal name for pin 147 in Section 4-1 “Pinout for 208-pin PQFP Package” on page
10.
2907
Inserted new voltage information for JTAGSEL signal in
Table 3-1, “Signal Description List”
and in Section 6.1 “JTAG Port Pins” on page 13.
2947
In Table 3-1, “Signal Description List,” on page 4, added new voltage information for OSCSEL
and TST pins.
2979
In Section 6.3 “Reset Pins” on page 13, new information on NRST and NRTST pins. 3003
Corrected ADC features in Section 10.4.11 “Analog-to-Digital Converter” on page 36. 2923
6221BS Power consumption figures updated with current values in Section 5.2 “Power Consumption”
on page 12.
Change to signal name for pin 47 in Section 4-1 “Pinout for 208-pin PQFP Package” on page
10.
2843
6221AS First issue.
Table 13-1. Revision History - current version appears first
Revision Comments Change
Req. Ref.