Datasheet
93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C
DS21749D-page 2 2003 Microchip Technology Inc.
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
(†)
VCC.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. V
SS ......................................................................................................... -0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
ESD protection on all pins ......................................................................................................................................................≥ 4kV
TABLE 1-1: DC CHARACTERISTICS
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at those or any other conditions
above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
All parameters apply over the specified ranges
unless otherwise noted.
V
CC = range by device (see Table on Page 1)
Industrial (I): T
A = -40°C to +85°C
Automotive (E): T
A = -40°C to +125°C
Param. No. Symbol Parameter Min Typ Max Units Conditions
D1 VIH1
V
IH2
High-level input voltage 2.0
0.7 VCC
—
—
VCC +1
V
CC +1
V
V
V
CC ≥ 2.7V
V
CC < 2.7V
D2 V
IL1
V
IL2
Low-level input voltage -0.3
-0.3
—
—
0.8
0.2 VCC
V
V
VCC ≥ 2.7V
V
CC < 2.7V
D3 VOL1
V
OL2
Low-level output voltage —
—
—
—
0.4
0.2
V
V
I
OL = 2.1 mA, VCC = 4.5V
I
OL = 100 µA, VCC = 2.5V
D4 VOH1
V
OH2
High-level output voltage 2.4
VCC - 0.2
—
—
—
—
V
V
I
OH = -400 µA, VCC = 4.5V
I
OH = -100 µA, VCC = 2.5V
D5 I
LI Input leakage current — — ±1 µAVIN = VSS to VCC
D6 ILO Output leakage current — — ±1 µAVOUT = VSS to VCC
D7 CIN,
C
OUT
Pin capacitance
(all inputs/outputs)
——7pFVIN/VOUT = 0V (Note 1)
T
A = 25°C, FCLK = 1 MHz
D8 ICC
write
Write current —
—
—
500
2
—
mA
µA
FCLK = 3 MHz, VCC = 5.5V
F
CLK = 2 MHz, VCC = 2.5V
D9 I
CC read Read current —
—
—
—
—
100
1
500
—
mA
µA
µA
F
CLK = 3 MHz, VCC = 5.5V
F
CLK = 2 MHz, VCC = 3.0V
F
CLK = 2 MHz, VCC = 2.5V
D10 I
CCS Standby current —
—
—
—
1
5
µA
µA
I-Temp
E-Temp
CLK = CS = 0V
ORG = DI = VSS or VCC
(Note 2) (N
OTE 3)
D11 VPOR VCC voltage detect
93AA46A/B/C, 93LC46A/B/C
93C46A/B/C
—
—
1.5V
3.8V
—
—
V
V
(Note 1)
Note 1: This parameter is periodically sampled and not 100% tested.
2: ORG pin not available on ‘A’ or ‘B’ versions.
3: READY/BUSY
status must be cleared from DO, see Section 3.4 "Data Out (DO)".