T30
T30 SAFETY Observe the safety regulations in the instruction manual of the Power Tool to be used or connected to this attachment. Also observe any applicable additional safety rules. Read the following safety instructions before attempting to operate this product. PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE. The attention of UK users is drawn to The Provision and Use of Work Equipment Regulations 1998, and any subsequent amendments. General ■ Disconnect power tool, when not in use.
T30 85dB(A) is exceeded. Routing sound pressure may exceed 85dB(A), so ear protection must be worn. ■ Eye protection. Wear safety goggles, spectacles or visors to protect the eyes from ejected waster particles. ■ Respiratory protection. Wear a face or dust mask, or powered respirator. Dust masks/filters should be changed regularly. ■ Do not switch router on with the cutter touching the workpiece. ■ The direction of routing must always be opposite to the cutter's direction of rotation.
T30 ■ The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug (see below left). Brown is for Live (L) (2), Blue is for Neutral (N) (3) and Green/Yellow is for earth (4). ELECTRICAL SAFETY Power Supply ■ Before replacing the top cover of the mains plug ensure that the cable restraint (5) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws.
T30 VACUUM CLEANING SAFETY General Safety General Safety Regulations when Routing Noise Fire and explosion hazard. The level of noise when routing may exceed 85 dB(A). It is therefore advisable to wear ear defenders especially if routing for long periods of time. ■ Never vacuum-clean inflammable fluids, such as gas, oil, alcohol, solvents, etc. Do not work near inflammable fluids or gas. Never vacuum-clean warm fluids or material at more than 60˚C, such as burning cigarettes, ashes, glowing coals, etc.
T30 ITEMS ENCLOSED MANUFACTURERS DECLARATION 1 x Cartridge Filter (12 micron for T30A) T30 (0.3 micron for T30AF & T30ALF) We declare under our sole responsibility that this product is in conformity with the following standards of standardised documents: EN 60335.1, EN 60335.2.2, EN 50081.1, EN 50082.1 in accordance with the directive 98/37/EC and following modifications 73/23/EEC, 93/68/EEC, 89/336/EEC.
T30 DESCRIPTION OF PARTS 4 1 1 Switch ON-OFF 2 Socket for auto-start 230V max. 2000 W safe load 2 3 110V max. 1000 W safe load 3 5 Switch AUTOMATIC: Position M: vacuum cleaner running Position A: vacuum cleaner automatically starts when the accessories attached to plug are activated. 6 4 Carrying handle 10 5 Motor filter 6 Float 7 Cartridge filter 7 14 9 11 -for T30A & T30/EURO (12 micron) -for T30AF & T30ALF (0.
T30 ASSEMBLY Some of the accessories are supplied inside the container and so must be removed before using the unit. ■ Insert the five castor wheels in their purposely provided housings under the container (9). 9 ■ Connect the hose to container (9). To remove it, push button (14) and pull the hose towards you. ■ The connection of the extension tubes and of its accessories is carried out by exerting a small amount of pressure. To remove them, turn the parts in the opposite direction and draw them apart.
T30 OPERATION Suction of Dry Dust and Dirt ■ The filter cartridge (7) has to be completely pushed in and is secured by turning the filter cartridge cap (10). Check that it fits correctly. ■ In order to remove the cartridge filter (7) turn the cap (10) anti-clockwise and draw the cartridge filter. Fix the paper-filter bag (8) to the inner side of the tube-connection in the container, ensuring it is fully seated.
T30 Suction of Fluids Before picking up fluids, do not forget to: - empty container (9) - remove paper-filter bag (8) - remove cartridge filter (7) Should the cartridge filter not be removed by mistake this could lead to motor damage. In order to guarantee enough air flow it is recommended not to immerse it completely in the fluids.
T30 T30 - SPARE PARTS LIST v3.0 07/2003 No. Qty. Desc. Ref. 1 2 3 4 5 6 1 1 1 2 5 1 1 1 1 1 1 1 1 1 15 1 1 1 1 1 1 1 1 1 7 1 1 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 Container Housing Motor Cover Motor Housing Container Clip Castor 3 Core Cable with Plug 230V UK 2 Core Cable with Plug 230V EURO 3 Core Cable with Plug 110V UK Cable Clip Washer 5.2mm x 11mm x 1.0mm Screw Self Tapping Pan 4.
T30 T30 - SPARE PARTS LIST Item Qty 34 35 36 37 38 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 0 2 1 1 1 1 1 1 1 0 60 1 v3.0 07/2003 Description Ref. Lower Motor Housing Foam Baffle Lower Housing Rubber Grummet External Float Float Cage Cartridge Filter 12 Micron (T30A) Cartridge Filter 0.
T30 T30 - SPARE PARTS DIAGRAM v3.
MANU/T30 v5.0 RECYCLABLE Trend Machinery & Cutting Tools Ltd. Odhams Trading Estate St Albans Road Watford WD24 7TR England Enquiries: _________________0800 487363 Technical Support: ___0044 (0) 1923 224681 Fax: _______________0044 (0) 1923 236879 Email: ___________mailserver@trendm.co.uk Web: ___________www.trendmachinery.co.uk © Copyright Trend 2003. No part of this publication may be reproduced, stored or transmitted in any form without prior permission.
