micom3 CarryOn MICOM-3TS-RDP HF-SSB Rapid Deployment Package Supplement to MICOM-3F/3T/3R Owner’s Guide 6886867J01A 6888882V09
MICOM-3TS-RDP HF-SSB Rapid Deployment Package Supplement to MICOM-3F/3T/3R Owner’s Guide 6886867J01A Cat. No.
Table of Contents Table of Contents Page Before You Begin..............................................................................................................iii General Safety Precautions ...............................................................................................iv Information for Safe, Efficient Operation...........................................................................v Exposure to Radio Frequency Energy...............................................................
MICOM-3TS-RDP Owner’s Guide ii
Before You Begin Before You Begin This Owner’s Guide is designed to acquaint you with the features, care, and installation of your micom3CarryOn radio (MICOM-3TS-RDP Rapid Deployment Package), part of the MICOM-3 family of HF/SSB transceivers.
MICOM-3TS-RDP Owner’s Guide Warnings, Cautions and Notes The following notations are used to place special emphasis on procedures, or to call attention to precautionary measures. Warning Caution Note An operating procedure, practice and so forth, which if not followed correctly, could result in personal injury, or loss of life.
Information for Safe, Efficient Operation Information for Safe, Efficient Operation Exposure to Radio Frequency Energy The FCC has established limits for safe exposure to radio frequency (RF) emissions from mobile two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before mobile two-way radios can be marketed in the U.S.
MICOM-3TS-RDP Owner’s Guide Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed as Fixed Site Control Stations If mobile radio equipment is installed at a fixed location and operated as a control station or as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in the standards and guidelines listed on page v: • The antenna should be mounted o
Information for Safe, Efficient Operation Driver Safety Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please: • Give full attention to driving and to the road. • Pull off the road and park before making or answering a call if driving conditions so require. Operational Warnings For Vehicles with an Air Bag Warning Do not mount or place a mobile radio in the area over an air bag deployment area.
MICOM-3TS-RDP Owner’s Guide Installation Safety Warning Consider the vehicle occupants’ safety when you choose a location for the MICOM-3TS-RDP. Do not place the suitcase overhead unless you take special precautions. If you have to mount the radio overhead, give it the added protection of a retaining strap. Grounding Warning Warning All equipment must be properly grounded according to the manufacturer’s instructions for safe operation.
Overview Overview General MICOM-3TS-RDP is an advanced transportable HF/SSB DSP-based communication system, intended for a very wide range of radio communications. Packed in a rugged suitcase, the MICOM-3TS-RDP provides a highly sophisticated solution for voice, data, fax and e-mail transfer, while remaining reliable and simple to operate.
MICOM-3TS-RDP Owner’s Guide Radio Options and Accessories • • • • • • • • • • • • • • • • • • • 2 RS-232 remote control interface Linear power amplifier interface Phone patch interface Data/fax modem interface MRC or RSS for PC High (0.
Overview The MICOM-3TS-RDP Suitcase The MICOM-3TS-RDP is designed for the rugged environment encountered in various transportation conditions (trucks, planes, boats, etc.), and meets the US MIL-STD-810E standard for shock and vibration. The suitcase is made of heavy gauge aluminum and is splash proof and dust resistant. The transceiver, control panel and power supply are shock mounted.
MICOM-3TS-RDP Owner’s Guide MICOM-3 Radio For detailed operating instructions, refer to the “Owner’s Guide, MICOM-3F/3T/3R HF-SSB Transceivers”, Publication 6886867J01A, supplied with the RDP.
Overview Power Supply Options The power supply unit is capable of operating with, and automatically identifying, either 110V/220V, 47-65 Hz AC or 12V DC power sources. The AC source has priority. When operating the MICOM-3TS-RDP using AC power, a backup battery can be connected (13.8V lead-gel or lead acid battery, maximum 45Ah), which will automatically be trickle charged. This offers an immediate backup power supply in case of a power failure.
MICOM-3TS-RDP Owner’s Guide Installation General This section describes the procedures for setting up the MICOM-3TS-RDP. These procedures can be performed by the system operator under field conditions, with no prior experience. The radio should be set up and configured in accordance with the instructions in the “Owner’s Guide, MICOM-3F/3T/3R HF-SSB Transceivers”, Publication 6886867J01A.
Installation in the area will enhance performance. The antenna should not be installed near power lines, highways, broadcast stations, electrical motors etc. If possible, the antenna should be erected with the grounded or low end of the antenna pointing in the general direction of the station you wish to contact. Broadband Antenna Grounding It is important to ensure that the antenna is correctly grounded, either via the grounding stake, or to a vehicle body.
MICOM-3TS-RDP Owner’s Guide Erecting a Broadband Antenna Using a Vehicle for Grounding This method is used if your MICOM-3TS-RDP is located in a vehicle, or if a vehicle is available and can be used for grounding. This will give better results than earth grounding. 1. Fit the grounding stake through the holes in the antenna spool. Pull out the black handle on the spool. Holding the stake in one hand, use the handle to wind and unwind the antenna wire. 2.
Installation Long-Wire Antenna Installation The antenna supplied with the MICOM-3TS-RDP Option G580 is a long-wire antenna. The antenna includes: • One 18m (60 ft) antenna wire • One stainless steel earth stake • One 5m (17 ft) length of coaxial cable fitted with connectors • Two throw cords with throwing weights This antenna is supplied wound on one slot of the spool, while the two throw cords used for installation are wound on the other slot.
MICOM-3TS-RDP Owner’s Guide Erecting an Inverted “L” Long-Wire Antenna 1. Open the four screws on the inner panel of the MICOM-3TS-RDP suitcase cover to remove the tuner. 2. Connect the black coaxial cable to the N-type RF antenna connector at the side of the tuner; connect the other end to the ANTENNA connector on the connector panel, on the suitcase body. 3.
Installation Erecting a Sloping Long-Wire Antenna 1. Open the four screws on the inner panel of the MICOM-3TS-RDP suitcase cover and remove the tuner. 2. Connect the black coaxial cable to the N-type RF antenna connector at the left side of the tuner; connect the other end to the ANTENNA connector on the connector panel on the suitcase body. 3.
MICOM-3TS-RDP Owner’s Guide MICOM-3TS-RDP Connections Most connections are made to the connectors in the connector panel of the MICOM-3TS-RDP (with the exception of the microphone, which is connected directly to the front panel of the MICOM-3 radio control head). AC POWER 85-267 VAC AUTO GND SYSTEM ANTENNA BAT. 12V FUSE 6.3A S.B Figure 8. MICOM-3TS-RDP Connector Panel Connecting the MICOM-3TS-RDP to Grounding It is highly recommended to connect the MICOM-3TS-RDP suitcase to the ground.
Installation When using DC power, connect the DC cable to the 3-pin DC power connector, BAT. 12V, on the MICOM-3TS-RDP connector panel. It is recommended to insert a 30A protection fuse in the positive lead of the battery cable. When using AC power, connect the AC cable to the AC POWER connector in the connector panel of the MICOM-3TS-RDP.
MICOM-3TS-RDP Owner’s Guide Maintenance Introduction This section provides maintenance information for the user of the radio. By carrying out the installation procedures correctly and following the maintenance instructions properly, you ensure continuous operation of your radio set. When an internal problem appears or is suspected, the radio internal BITE (built-in test equipment) will assist you in locating the source of this possible problem to inform the service representative accordingly.
Maintenance Troubleshooting In case a problem or malfunction occurs, identify the closest description appearing in Table 1 and then perform the listed corrective actions. Table 1. Troubleshooting Chart Problem Blank display Corrective Actions CHECK • DC and/or AC power cables are connected properly. • The 30A fuse installed in the fuse holder located on the red wire of the DC power cable is good. • The 6.3A fuse installed in the AC POWER connector located on the MICOM-3TS-RDP connector panel, is good.
MICOM-3TS-RDP Owner’s Guide Service Proper repair and maintenance procedures will assure efficient operation and long life for this product. A maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. Through its maintenance and installation program, the manufacturer makes available the finest service to those desiring reliable, continuous communications on a contract basis.
Maintenance Model Complements micom3CarryOn (RDP) with G580 ATU System M91AMN0KV5-K & G580 Long Wire Antenna Inverted FAA5507A RDP ATU Board FLA5515A RDP Customer Kit FKN5913A Suitcase FLN6442A Power Supply for RDP FPN5513A Microphone FMN1615A DC Cable for RDP (20”) FKN4829A RDP Assembly FHN6063A Control Head Unit FLN2775A Low RF Assembly FLN2773A Blank Panel for RDP FLN2674A High Power Unit FLN3173A Control Cable HKN6098A Digital Noise Blanker S135AD DC Cable FKN4830A RSS Pro
MICOM-3TS-RDP Owner’s Guide micom3CarryOn (RDP) with G581 Broadband Antenna M91AMN0KV5-K & G581 18 Suitcase FLN6442A Power Supply for RDP FPN5513A Microphone FMN1615A DC Cable for RDP (20”) FKN4829A RDP Assembly FHN6063A Control Head Unit FLN2775A Low RF Assembly FLN2773A Blank Panel for RDP FLN2674A High Power Unit FLN3173A Control Cable HKN6098A Digital Noise Blanker S135AD DC Cable FKN4830A RSS Programming Cable 0102703K65 HDW ATU MICOM-3 FHN6013A Owners Guide for MICOM-3
Technical Specifications Technical Specifications This section lists the main technical characteristics of the equipment. See the “Owner’s Guide, MICOM-3F/3T/3R HF-SSB Transceivers”, Publication 6886867J01A for detailed specifications. General Model M91AMN0KV5-K & G580 or G581 Transmit Frequency Range 1.6 to 30 MHz Receive Frequency Range 0.1 to 30 MHz (0.1 to 1.6 MHz reduced performance) RF Input Impedance 50 Ω Sensitivity SSB: 0.
MICOM-3TS-RDP Owner’s Guide Broadband Antenna Frequency Range 2 to 30 MHz Power Rating 100 W PEP Input Impedance 50 Ω nominal VSWR Max. 2:1 across operating range Input Connector BNC socket Coaxial Cable 5m (17 ft) long RG58 C/U, fitted with N plug Total Length when Erected 16m (55 ft) Antenna and Elect. Elements Stainless steel Packed Weight 1.2 kg (including grounding stake and coaxial cable) Specifications subject to change without notice.
