Table of contents 1. INTRODUCTION ............................................................................................................................... 1 2. INSTALLATION ................................................................................................................................. 3 2.1. INSTALLING THE HARDWARE .....................................................................................................................................3 2.2. INSTALLING THE SOFTWARE .......
5.2.3.1. Change map ....................................................................................................................................30 5.2.3.2. Display traffic direction/street names ............................................................................................30 5.2.3.3. POIs ..................................................................................................................................................31 5.2.3.4. Display saved addresses ..................
6.5.3.2. Delete POI Category .......................................................................................................................60 6.5.4. Rename.........................................................................................................................................................61 6.6. NOTES AND TIPS ...................................................................................................................................................61 7.
1. Introduction This manual will help you to get the best out of your ViaMichelin Navigation X-930 device.
The device is fitted with a touchscreen, and is designed to be operated with your fingertips for greater convenience. You can also use the stylus provided (located on the right of your ViaMichelin Navigation X-930). The "Exit" key in the Main Menu is used to switch off the ViaMichelin Navigation X-930. To turn it on again, just press the on/off button.
2. Installation 2.1. Installing the hardware • Installing on the windscreen: install the car mounting system on the windscreen by applying pressure to the suction pad and then turning the screw clockwise (reverse the procedure to remove the windscreen mounting system). • Installing on the dashboard: remove the protective film from the plate, position it on a perfectly smooth and clean surface by pressing evenly over the whole area, then install the mounting system as described above.
2.3. Activating the GPS After connecting the ViaMichelin Navigation X-930 and installing the software on the SD rd card, press the 3 button from top on the front. This will take you directly to the GPS settings page: • The green "V" means that the GPS is on. • "NO FIX/FIX: 2D/FIX: 3D" indicates better signal reception, and therefore more accurate positioning. • "SAT" indicates the number of satellites used to calculate your position.
3 General Introduction The ViaMichelin Navigation X-930 has several buttons on its front that provide direct access to certain functions: 3.1. Left-hand buttons • top button: increases the volume of navigation voice messages. • bottom button: reduces the volume of navigation voice messages. 3.2.
around the menus and screens on your ViaMichelin Navigation X-930 device or to perform a “reset” (for more details, refer to paragraph 10.3).
4.
4.1. Address • Click "Address" • Enter the name of the destination state by clicking the letters of your choice. You can enter the complete name of the state, the first letters or the short name. Example: You can enter TEXAS, TEX or TX. • If the message "No address matches your request. Please try a new search" appears, click OK and enter a new state name. For more details, refer to "§ 4.7 - Notes and Tips".
• Enter the name of the destination town. • If the message No POI matches your request. Please try a new search" appears, click OK and enter a new town name. • Click on Search to start a search after entering your search criteria or click on Display all to bring up a list of the towns. • The Back button returns you to the previous page and the Cancel button stops the current search. • The State button (top left) returns you to the Destination State screen where you can change the search state.
• - Then click on the position you want: - Centre on street: if you want to position the arrival point in the geographical centre of the selected street. - Select House Number: if you want to specify the house number. - Select street intersection: if you want to position the arrival point at an intersection with another street. For subsequent searches: The state is pre-selected (stored in the memory since your last search) and you immediately access the Destination Town screen.
• • • • • want to search for a different house number. You then return to the "Select House Number" screen. If there is no vehicle access to the house number you entered (pedestrian road, private road, etc.) the message “No vehicle access to address. We have selected the nearest road” is displayed. Click "OK" to position your arrival point automatically as close as possible to your desired destination point. The next screen provides a summary of the settings used to calculate your route.
• Then click the place where you want to search: - Town: looks for a selected POI in the town you choose. - GPS Position: looks for a selected POI near the position given by the GPS. - Departure Point: inactive in this method of route planning. - Arrival Point: looks for a POI near your arrival point. 4.2.1. Town • Click "Town". • Enter the name or postcode of the destination town. If the message “No address matches your request. Please try a new search” appears, click "OK" and enter a new town name.
• Click the town you want, or click "Change" if you want to modify the search criteria. You then return to the "Destination Town/Post code" page. • Then click the POI you want or "Refine search" if you want to specify particular search criteria: - Name Search - Criteria Search 4.2.1.1. Name Search • Click "Name Search". • Enter the name of the POI you want or click "Display all" for a list of the POIs found by the system. 4.2.1.2. Criteria Search • Click "Criteria search".
• You can click the direction arrows: - left: to view the previous POI - right: to view the next POI • Click "OK" to confirm your choice, or "Back" to return to the list of POIs on the previous screen. • You then go to the "Route Summary" screen. • Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route. • The Navigation screen is displayed once the route has been calculated. • Start driving.
4.3. Select on map • Click "Select on map". • Zoom in and move the map to position the location marker on the arrival point you want. For more details, refer to "§4.7 Notes and Tips". • Click "Confirm arrival" to accept the position of your arrival point or "Back" to return to the previous screen. • You then go to the "Route Summary" screen. • Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route.
• Click the category where the saved address you want is located. • Click the type of search you want to do: - Name search to find a saved address from a name. - Search near to find a saved address near a place. 4.4.1. Name Search • Click "Name Search". • Enter the name of the saved address you want or click "Display all" for a list of the saved addresses found by the system. Click "Back" to return to the previous screen.
• Enter the name of your destination town by clicking the relevant letters or postcode or click "Display all" to bring up a list of the main towns. Click "Back" to return to the previous screen. • Click "Search". • If there are several town names that meet your criteria, the system lists them. Click the direction arrows to view all the town names. Click the town you want or click "Change" to return to the town name screen. • On the list displayed on the screen, click the saved address you want.
• Start driving. The voice guidance system will give you directions to your destination. For more details, refer to "§4.7 Notes and Tips". 4.5. History • • • • Click "History". A list of the last 10 destinations is displayed. Click the address you want. You then go to the "Route Summary" screen. Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route. • The Navigation screen is displayed once the route has been calculated. • Start driving.
• Enter the latitude (N/S) in degrees, minutes and hundredths of minutes. Specify the direction: North or South, by selecting "N" or "S". • Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route. • The Navigation screen is displayed once the route has been calculated. • Start driving. The voice guidance system will give you directions to your destination. For more details, refer to "§4.7 Notes and Tips". 4.7.
• Click the screen and move the map in the direction you want, to display the area you are interested in. • If the coordinates show a point a long way from a road, the message “The place selected must be less than 25km from a road” appears. In this case, click "OK" to return to the longitude input screen. • If several saved addresses or POIs are very close together, you will need to zoom in to separate them. • The history only contains the last 10 destinations used.
5. Plan your journey • In the Main Menu, click "Plan your journey". • You can then plan your journey by one of 3 methods: - Plan a route: to specify a departure and arrival point - Display a map: to select your departure and arrival points directly on the map - Search for a POI: to plan a route to or from a POI 5.1. Plan a route • Click "Plan a route".
5.1.1. Address • Click "Address". • Enter the name of the destination state by clicking the letters of your choice. You can enter the complete name of the state, the first letters or the short name. Example: You can enter TEXAS, TEX or TX. • If the message "No address matches your request. Please try a new search" appears, click OK and enter a new state name. For more details, refer to "§ 4.7 - Notes and Tips".
• Enter the name of the destination town. • If the message No POI matches your request. Please try a new search" appears, click OK and enter a new town name. • Click on Search to start a search after entering your search criteria or click on Display all to bring up a list of the towns. The Back button returns you to the previous page and the Cancel button stops the current search. The State button (top left) returns you to the Destination State screen where you can change the search state.
For subsequent searches: The state is pre-selected (stored in the memory since your last search) and you immediately access the Destination Town screen. If you want to change the state being searched, click the State button top left and select a new state. For more details, refer to "§5.4 Notes and Tips".
• Then click the place where you want to search: - Town: looks for a POI in your chosen town (for more information, refer to §4.2.1.). - GPS Position: looks for a POI situated near the position given by the GPS (for more information, refer to §4.2.2.). - Arrival or departure point: looks for a POI near your arrival or departure point (for more information, refer to §4.2.3.). 5.1.3. Select on map • Click "Select on map".
• Click the category where the saved address you want is located. • Enter the name or the first letters of the saved address you want to find or select "Display all" to bring up your list of saved addresses. • If you have no saved addresses in the system, a message is displayed: "No saved addresses match your request. Please try a new search” (For more information on creating or deleting a saved address, refer to §6.5.). • Otherwise the list of saved addresses is displayed. Click the one you want.
5.1.6. GPS Coordinates • Click "GPS coordinates". • Enter the longitude (E/W) in degrees, minutes and hundredths of minutes, then specify the direction: East or West, by selecting E or W and click on "OK". • Enter the latitude (N/S) in degrees, minutes and hundredths of minutes. Specify the direction: North or South, by selecting N or S. • Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route. • Start driving.
• Click "Main Menu" to return directly to the Main Menu. • Click "Map Options" to access different options or functions. • You access different options or functions: - Location marker options: to make certain selections on the place identified by the location marker. - Search: to perform searches on the map. - Options: to access options for changing the map display. - Centre: to centre the map on the basis of your choice.
The location marker is automatically positioned on the departure point or destination point. You can then zoom to access the desired map level, centred on the departure point or destination point. 5.2.1.2. Add to My saved addresses • Click "Add to My saved addresses". • Select the category in which you want to store your saved address. • Enter the name you want to give your saved address. • Click "OK".
5.2.3. Settings • Click "Settings". • You can then access different functions: - Change or delete map: to change or delete a map. - Display traffic direction/street names: to display the traffic direction or street name for each section of street. - POIs: to go directly to the page where you can select the POIs displayed on the map. - Saved addresses: to go directly to the page where you can select your saved addresses from the map display. 5.2.3.1.
o indicates a street where a section is not accessible to cars (pedestrian streets, private roads, etc.) • The name of the street where the location marker is positioned is always displayed at the bottom of the screen. • Click "Display street names" to have the maps display the street names again. 5.2.3.3. POIs • Click "POI". • You use this option to select the POIs that will be displayed on the map (given the right zoom level).
• The "Select all/Deselect all" button automatically selects or deselects the whole list of saved addresses displayed. 5.2.3.5. Display driving directions This function splits the part of the screen used to display the map, so that above the map there is a zone which shows the changes of direction for the whole journey. To stop the driving directions being displayed on the map, click "Map options / Options / Hide driving directions". For more details, refer to "§5.4 Notes and Tips". 5.2.4.
5.2.5. Navigation • Click "Navigation". • You can choose to access Navigation mode or to display the Navigation screen to simulate Navigation on the calculated route. 5.2.5.1. Navigation • Click "Navigation". • This function takes you directly to Navigation mode. • The "Route summary" screen shows your destination and the settings used to calculate the route. • Click "OK" to go directly into Navigation mode • The Navigation screen is displayed once the route has been calculated.
• You then have 4 search options: - Town - GPS Position - Departure point - Arrival Point 5.3.1. Town • Click "Town" • By default, the last state in which you made a search is stored in memory. If you want to change the state being searched, click the State button top left and select a new state. • Enter the name of the destination town. • Click "Display all" to get a list of the main towns. For more details, refer to "§5.4 Notes and Tips".
• Click on the POI you want. They are classified on the basis of how close they are to the centre of the selected town. Or click "Refine" search if you want to restrict the search using new criteria: - name search for more information, refer to §4.2.1.1. - by criteria for more information, refer to §4.2.1.2. • You can click the direction arrows: - left: to view the previous POI - right: to view the next POI • Click "POI actions".
5.3.1.3. Navigate to • Click "Navigate to". • Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route. • The Navigation screen is displayed once the route has been calculated. • Start driving. The voice guidance system will give you directions to your destination. 5.3.1.4. Centre on map • Click "Centre on map". • The map is centred on the selected POI and on the location marker.
• Click "POI options" or "Back" to return to the previous screen. • You can then: - Phone: - This function is for devices fitted with a telephony option, and is not available on the X-930 system Add to My saved addresses: to make the selected POI a favourite in your saved addresses (For more information, refer to §5.3.1.2). Navigate to: to establish a route to the selected POI (for more information, refer to §5.3.1.3).
• Click "POI actions". • You can then: - Phone: - This function is for devices fitted with a telephony option, and is not available on the ViaMichelin Navigation X-930. Add to My saved addresses: to make the selected POI a favourite in your saved addresses (For more information, refer to §5.3.1.2). Navigate to: to establish a route to the selected POI (for more information, refer to §5.3.1.3). Centre on map: to centre the map on the selected POI (for more information, refer to §5.3.1.4).
• If several saved addresses or POIs are very close together, you will need to zoom in to separate them. • The history only contains the last 10 destinations used. It is automatically updated: each new destination replaces the oldest. • If the coordinates show a point a long way from a road, the message “The place selected must be less than 25km from a road” appears. In this case, click "OK" to return to the previous screen.
6. Settings • In the Main Menu, click "Settings". • This then takes you into the settings or information menus: - Navigation - Map - POI - General - My saved addresses 6.1. Navigation • Click "Navigation". • You access menus that you can use to change certain navigation settings: - Display: to adjust the display settings. - Route: to adjust route or speed settings. - Sound: to adjust the volume of the different audible alarms. - Warner: to adjust the warning signal thresholds.
6.1.1. Display • Click "Display". • You can select 3 display settings for navigation: Day mode/Night mode 2D View/3D View Navigation display 6.1.1.1. Day mode/Night mode • Click "Night mode". • The screen becomes less bright and the map colours change to make the display more comfortable for night driving. • Click "Day mode". • The screen brightens and the map colours change to give the ViaMichelin Navigation X930 display maximum visibility in full daylight.
6.1.1.2. 2D View/3D View • Click "2D View". • The maps displayed during navigation are shown in 2D like a "paper" map. The direction of navigation is automatically shifted towards the top of the screen. • Click "3D View". • The maps displayed during navigation are shown in 3D, i.e. with spatial representation. The direction of navigation is automatically shifted towards the top of the screen. 6.1.1.3. Navigation display • Click "Navigation display".
• Click the position you want and then select the field: - Distance remaining - Time remaining - Arrival time - Time - Speed - Direction Distance remaining This is the distance remaining to the arrival point, given in kilometres or miles depending on the distance unit selected. Time remaining This is the time remaining until arrival. This time is assessed on the basis of the distance remaining and the average speeds set in ViaMichelin Navigation X-930, excluding any stops or breaks.
6.1.2. Route • Click "Route". • You have 2 options: - Route settings - Speed limits 6.1.2.1. Route settings • Click "Route settings". • There are 2 options for route settings: - Transport type: Car/Pedestrian - Route type: Quickest route/Shortest route • Click the left or right arrows to display the setting you want. The settings are on once you select them. • Click "Back" to return to the previous screen or "Main Menu". 6.1.2.2. Speed limits • Click "Speed limits".
The default average speeds are: Motorways: Major roads: Other main roads: Local roads: Streets: Small streets: 105 kph 90 kph 70 kph 55 kph 40 kph 30 kph 65 mph 55 mph 45 mph 35 mph 25 mph 15 mph The range of speed limit settings is between 30kph and 180kph or between 15mph and 110mph. 6.1.3. Sound • Click "Sound". • Click the left or right arrows to display the setting you want: "Sound" and "Sound choice".
• You can set 3 types of audible warnings in ViaMichelin Navigation X-930: - Speed limit warner: sets off a warning alarm when the speed limit for a given road type is exceeded. - POI Warner: to set the POI categories which will trigger an alarm when they are nearby. - Saved Adresses Warner: to set the categories of saved addresses which will trigger an alarm when they are nearby. 6.1.4.1. Speed limit warner • Click "Speed Limit Warner".
• The "POI Warner" can be set to sound an audible alarm when a POI is nearby. • Tick the boxes by the POI categories for which you want to trigger an alarm when they are nearby: a first message is emitted 30 seconds then a second message 10 seconds before passing a POI in one of the selected categories. • Click "More criteria" if you want to break your selection down into subcategories of POIs. • The "Select all/Deselect all" button automatically selects or deselects the whole list of POIs displayed. 6.1.4.
• This function shows the GPS satellite signal reception and gives the position coordinates evaluated by the GPS. For more details, refer to "§6.6 Notes and Tips". When using the ViaMichelin Navigation X-930 for the first time, we recommend you do so in an open space in order to ensure the best possible satellite reception. Activating the GPS system for the first time can take several minutes, depending on the surroundings and the quality of the GPS signals.
• This then takes you into the settings or information menus: - Change or delete map: to change or delete a map. - Display traffic direction/street names: to display the traffic direction or street name for each section of street. - POIs: to go directly to the page where you can select the POIs displayed on the map. - My saved addresses: to go directly to the page where you can select your saved addresses from the map display. 6.2.1. Change map • Click "Change map". • Click "Change maps".
• The name of the street where the location marker is positioned is always displayed at the bottom of the screen. • Click "Display street names" to have the maps display the street names again. 6.2.3. POIs • Click "POI". • You use this option to select the POIs that will be displayed on the map (given the right zoom level). • Some subcategories of POI can be displayed separately, if the category contains several subcategories. Click "More criteria" to access a list of these subcategories.
6.4. General • Click "General". • This then takes you into the settings or information menus: - Language - Units - Power status - Brightness - Time - ABOUT 6.4.1. Language • Click "Language". • You use this option to set: - The Interface language: This is the language in which the menus are displayed. The available languages are: French, English, German, Spanish and Italian. - The Voice guidance language: this is the language used in voice messages during Navigation.
6.4.2. Units • Click "Units". • Click the left and right arrows to select the distance unit you want to use to calculate routes and to display distances on the Navigation screen. You can select: km (kilometres) or miles. 6.4.3. Power status • Click "Power status". • This screen shows the percentage of "Remaining battery power" or, if the device is connected to a power source, "Charging". For more details, refer to "§6.6 Notes and Tips". 6.4.4. Brightness • Click "Brightness".
6.5. My saved addresses • Click "My saved addresses". • You then access four easy-to-use submenus where you can manage your saved addresses: - Create: to create a new saved item. - Change: to change an existing saved item. - Delete: to delete an existing saved item. - Rename: to rename an existing saved item. 6.5.1. Create • Click "Create". • Click the category in which you want to create a saved item. • You can then create your new saved item by one of 6 methods: - Address: to find a specific address.
6.5.1.1. Address • Click "Address" • Enter the name of the destination town. • By default, the last state in which you made a search is stored in memory. If you want to change the state being searched, click the State button top left and select a new state. For more details, refer to "§6.6 Notes and Tips". • Click "Search" to start the search. The "Cancel" button stops the current search. • If there are several towns that meet your criteria, a list of towns is displayed.
• Click the street you want, or click "Change" if you want to modify the search criteria. You then return to the "Street" screen. • Then click the position you want: - Centre on street: if you want to position your saved item in the geographical centre of the street (for more information, refer to §4.1.1.). - Select House Number: if you want to specify the house number (for more information, refer to §4.1.2).
Town • You go directly to the "Select Town/Post code" screen. • Enter the name of the town or postcode by clicking the appropriate letters or numbers. • If the message “No address matches your request. Please try a new search” appears, click "OK" and enter a new town name. • By default, the last state in which you made a search is stored in memory. If you want to change the state being searched, click the State button top left and select a new state. For more details, refer to "§6.6 Notes and Tips".
• You can click the direction arrows: - left: to view the previous POI - right: to view the next POI • Click "OK" to confirm your choice • You then go to the "Route Summary" screen. • Click "OK" to start calculating the route or "Change Route" if you want to use a different method to calculate the route. • Start driving. The voice guidance system will give you directions to your destination. For more details, refer to "§6.6 Notes and Tips".
• Zoom in and move the map to position the location marker on the address you want. For more details, refer to "§6.6 Notes and Tips". • Click "OK". • Enter the name of your new saved item. • Click "OK". You then return to the saved addresses menu screen. 6.5.1.4. History • Click "History". • A list of the last 10 destinations is displayed. Click the address you want. • Enter the name of your new saved item. • Click "OK". You then return to the saved addresses menu screen. 6.5.1.5.
• Enter the latitude (N/S) in degrees, minutes and hundredths of minutes, then specify the direction "N" or "S": • Click "OK". • Enter the name of your new saved item. • Click "OK". You then return to the saved addresses menu screen. For more details, refer to "§6.6 Notes and Tips". 6.5.2. Change • Click "Change". • On the list displayed, click the category you want. • Enter the name of the saved address to change or click "Display all" for a list of the saved addresses stored in the selected category.
6.5.3. Delete • Click "Delete". • You can then choose to: - Delete saved address - Delete POI Category 6.5.3.1. Delete saved address • Click "Delete saved address". • On the list displayed, click the category you want. • Enter the name of the saved address to delete or "Display all" to get a full list of saved addresses. • If several saved item names match the search criterion, a list is displayed. Click on the name of the saved item to delete.
• All the POIs in the selected category will be deleted automatically. 6.5.4. Rename • Click "Rename". • On the list displayed on the screen, click the saved item category you want to rename. • Enter the name of the saved item you want or click "Display all" for a list of the saved addresses found by the system. • Click the direction arrows to scroll through the whole list. • Click the saved address you want. • Enter the new name you want to give your saved item. • Click "OK".
• In Navigation mode, POIs are displayed in real time. The icons showing the position of the POIs are thus displayed on the map and move with it. If you select a lot of POI categories to display or if you clicked "Select all", the information on the screen may update more slowly. • When the selected "Map language" is different from the "Interface language", town names, street names, etc., must be searched for in the "Map language".
7. Installing the DVD-ROM • The DVD-ROM supplied with your ViaMichelin Navigation X-930 contains 2 programs: - POI Manager: used to install “*.poi” or “*.asc” files on your system. - SD Manager: to restore your SD card in the event of an error. 7.1. Connecting ViaMichelin Navigation X-930 to the PC • To make sure that files are transferred from the PC to the ViaMichelin Navigation X-930 with maximum efficiency, we advise you to download and install the latest version of Microsoft’s ActiveSync® software.
• If the ActiveSync software is not detected on your PC, the installation procedure prompts you to install version 3.8 of ActiveSync. Then click "Next" and install Microsoft’s ActiveSync ® software. • Empty the cache, Internet temporary files and the trash can. • Close all other applications before installing the software.
• Select the folder in which you want to install the software and then click "Next". • Click "Next". • Click "Cancel" only if you want to stop the installation.
• Click "End" to complete the installation process. • Disconnect the USB cable from your PC, then from your ViaMichelin Navigation X-930. • If the DVD-ROM does not start automatically (autorun), click "My Computer", then the icon of DVD-ROM drive containing the DVD-ROM. • Click "Setup" (or "Setup.exe" if the file extensions are shown). The first window of the installation procedure should then open. • Follow the screen prompts. 7.3.
7.3.1.1. New type of POI • Click "New type of POI". • Give your POI file a name. • You can click "Change icon" to select a specific icon (cf. §8.4 on creating “*.asc” files). • Click the green "V" to confirm your choice or the red "X" to stop transferring the file or the arrow to return to the previous step. 7.3.1.2. Change type of POI • Click "Change type of POI". • Give your POI file a new name. • You can click "Change icon" to select a specific icon (cf. §8.3 and 8.4 on creating “*.asc” files).
To optimise the use of your ViaMichelin Navigation X-930, we recommend that no more than 6 personal POI files be imported. 7.4. SD Manager • Connect ViaMichelin Navigation X-930 to your PC • Start the "SD Manager" program (the default location is: Start/Programs/ViaMichelin/ ViaMichelin Navigation PND/SD Manager). • Select the item to be restored (just the application or the map). By default, the target medium is the X-950 (corresponding to the X-930). Select restore the application only.
• Let the refresh process continue until the end message. • You can also use an SD card reader to restore an SD card. Just copy the whole of the "SDCARD-PND" folder to the SD card. The default location folder is "C:\Program Files\ViaMichelin\ViaMichelin Navigation PND North America". • The time for SD Card restore depends on the performance of the computer used for this operation. We strongly recommend that you recharge the ViaMichelin Navigation X-930 fully before attempting to restore an SD card. 7.5.
• Choose the map set that you want to export to your SD card. By default, the target medium is the X-930. • After choosing the country to export, click the green "V". • Let the refresh process continue until the end message. • Click "OK" to close the window. • Disconnect the USB cable from your PC, then from your ViaMichelin Navigation X-930. 7.6. Repair This procedure will be necessary if the software files on your PC are damaged or missing. • Insert the DVD-ROM in your PC’s DVD drive.
• Click "Repair" and then click "Next". • Click "End" to close the window. • Disconnect the USB cable from your PC, then from your ViaMichelin Navigation X-930. 7.7. Uninstalling the programs • Insert the DVD-ROM in your PC’s DVD drive.
• The installation procedure starts automatically: It detects the presence of the programs and prompts you: either to "Add" a new map set. or to "Repair" the existing installation. Or to "Delete" the existing software installation from your PC. • Click "Delete" and then click "Next". A confirmation message is displayed. • Click "Yes" to confirm that you want to delete the programs or "No" to return to the previous screen. • Click "End" to close the window.
8. Additional Information • This chapter contains additional instructions on the different menus, to help you get the best out of your ViaMichelin Navigation X-930 system. 8.1. Free Navigation display • If you just want to follow your position on the map, you can use the "Centre on GPS" position option: - Open the "Main Menu". Click "Plan your journey". Click "Display a map". Click "Map options". Click "Centre". Click "On GPS position".
- The square at the top left of the screen shows the next change of direction and the distance to that change of direction. - The 3 top fields show, depending on the setting: - The "Distance remaining" - The "Time remaining" - The "Arrival time" - The "Time" - The "Speed" - The "Direction" To choose which information to show, click on one of the positions, then click on the position you want to change. Then select the indicator you want. - The name of the road you need to take at the next direction change.
• Save this file in the folder of your choice. • Check that your ViaMichelin Navigation X-930 system is connected and that the link with your PC is working. • Start "POI Manager". • Select the saved "asc" file in the folder of your choice and confirm. • Select the category of saved addresses to which imported saved addresses will be attached. • After importing the file into your ViaMichelin Navigation X-930, you can set the display and the POI Warner as you want.
9. POIs 9.1. How do you Navigate to a POI? • In the Main Menu, click "Navigate to", then "POI", select the category of POI you want and then select the details required. 9.2. How do I search for a POI? • From the "Plan a route" menu, select "Display a map", "Map options", "Search", "POI" and select the category of POI that you want to search for. Then, you can search in a town, near the GPS position, near the departure point or arrival point.
• The description contains the name of the POI, its category, its address, its telephone number and its Internet site.
10. Useful Information 10.1 Memory card contents • The memory card provided contains the United States software and map set. • The SD card contains 4 folders: - InstallSD contains the application needed to install the programs on ViaMichelin Navigation X-930. - MapSonic contains the programs to install. - VMNav_Maps contains the map files (“*.fdp”) and the settings files(“*.fdp.isv” and “*.pms”) which store the card status when the system is shut down (area displayed, zoom level, POIs displayed, etc.).
• To perform a soft reset, use the stylus to press the "reset" point on the back of your ViaMichelin Navigation X-930 device. • Soft reset closes the application and restarts ViaMichelin Navigation. Comment: • Only procedures running at the time of the reset may be lost (e.g. the current route). 10.3.2. Hard reset • Hard reset restores your product to its initial conditions. After this operation, you will need to reinstall the software.
10.5. Technical information Dimensions (L x W x H) in inches Weight Cigarette lighter socket cable voltage Screen 4.8 (L) x 2.8 (W) x 0.7 (D) 138 g 12 V Transflective TFT with non-reflective coating – QGVA – LCD 3.5’’ (55 x 74 cm – 320 x 240 pixels) 65,536 displayable colours Processor Processor speed Operating system ROM memory RAM memory Intel PXA 270 312 MHz Windows CE.net 4.2 32 MB 32 MB USB link v 1.
11. What to do if… In this table, we suggest a few answers to frequently asked questions: The device does not switch on when I press the “ON/OFF” button: During navigation, the voice messages are in another language: What is the difference between calculating the shortest and the quickest route? How do you go about installing the DVD-ROM on the PC if you get an error message when you start the DVD-ROM? Check that the “Lock” button (on top of the device) is not engaged.
The device does not recharge when it is connected in the car: What should I do if navigation is very slow? 82 - follow the instructions on the screen. Once the software is successfully installed, delete the temporary folder and its contents from your PC’s hard disk. Check that the cigarette lighter socket and the mini USB socket are properly connected and that the cable diode light is on.
12. Rights and warranties We thank you for having purchased a ViaMichelin Personal Navigation Device (hereinafter “ViaMichelin Product”). Use of the software and data provided with the ViaMichelin Product is subject to a licence granted by ViaMichelin, and/or other suppliers, to the end-user (hereinafter "you"), for his/her personal use, in accordance with the following end-user license agreement. 12.1. END-USER LICENSE AGREEMENT Please read this end-user license agreement carefully.
You are not authorised to extract, reproduce, represent, modify, adapt or extract the Data integrated into the Software. In particular, you are strictly prohibited from downloading the digital maps or Data contained in the Software and from transferring them onto other software and/or equipment. You are not authorised to lease or lend the Software or to use it for business or professional purposes.
acquired or used, certain data included in the Software may have been modified without ViaMichelin or its suppliers having been informed of this. 5. This warranty does not cover real time traffic information services that you may access using your ViaMichelin portable navigation system, subject to availability of these services in the country in which you are travelling. Such services are provided under the sole responsibility of the respective providers, which may be private or public entities.
