Mi Smart LED Ceiling Light User Manual
EN Product Overview Read this manual carefully before use, and retain it for future reference. Lampshade Mounting Hole Wiring Hole Terminal Block Junction Box Connector Base ×4 Wall Plug ×4 Self-tapping Screw Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.
EN Installation 1. Drill holes Place the base in the position the ceiling light will be installed, and mark the positions of the mounting holes, then remove the base. Use a φ6 mm drill to drill holes with a depth of at least 40 mm, then insert the included four wall plugs into the holes. 2. Fix the base Lead the stripped wires through the wiring hole in the base, and then align the mounting holes with the wall plugs.
EN 3. Connect the stripped wires The terminal block connector is suitable for wires with a cross-sectional area of 0.75–1.5 mm². Strip about 6–8 mm of the wires, then connect the neutral, ground, and live wires according to the marks (N, , and L) to the terminal block connector on the ceiling light. Use a screwdriver to clamp down each line by tightening the screws. Gently pull each wire to ensure it has been firmly connected.
EN Note: Try to wiggle the lampshade around to make sure it is properly and firmly installed. Otherwise, it may fall down. Connect with Mi Home/Xiaomi Home App This product works with Mi Home/Xiaomi Home app *. Control your device, and interact it and other smart home devices with Mi Home/Xiaomi Home app. Scan the QR code to download and install the app. You will be directed to the connection setup page if the app is installed already.
EN * The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app displayed on your device should be taken as the default. Note: The version of the app might have been updated, please follow the instructions based on the current app version. Apple HomeKit Smart Control 1. Open the Home app on your iPhone or iPad. 2.
EN Wall Switch Control Use the wall switch to turn on and off the ceiling light within 5 seconds, you can change the color temperature from warm yellow light, white light to night light by default. You can set the favorite light via the app. Note: Cycling the three light modes twice and pressing the wall switch again will restore the factory settings of the ceiling light.
EN cover of the light board, then remove the protective cover of the light board and unplug the wiring connected to the light board. Finally, uninstall the two rivets from the light board, and then remove the light board. 2. Install the light source Place the light board on the base, and use two new rivets to fix the light board onto the base. Connect the wiring, then install the protective cover on the light board with three new rivets to fix the cover onto the base.
EN Specifications Model: MJXDD01SYL Power Factor: >0.9 Operating Temperature: -10°C to 40°C Operating Humidity: 0–85% RH Color Temperature: 2700–6000 K Rated Input: 100–240V～ 50/60Hz Max. 0.5A Rated Power: 45 W (81 × 1 W/LED module) Compatible with: Android 4.4 & iOS 9.0 or above Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz, Bluetooth 4.2 BLE Operating Frequency:2412-2472 MHz (Wi-Fi) Maximum Output Power: 18.95 dBm (Wi-Fi) 2402-2480 MHz (BT) 4.
EN Precautions Make sure the voltage is consistent with the ceiling light's operating voltage before use. Using the mismatched voltage may damage the ceiling light and cause safety hazards. Do not replace the light source of the ceiling light by yourself. The light source should only be replaced by the manufacturer, after-sales service, or a qualified electrician. The ceiling light generates heat during working. Please keep it is well ventilated for heat dissipation.
EN EU Declaration of Conformity Hereby, Qingdao Yeelink Information Technology Co., Ltd. declares that the radio equipment type MJXDD01SYL is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.mi.com/en/service/support/declaration.html.
Manufactured for: Xiaomi Communications Co., Ltd. Manufactured by: Qingdao Yeelink Information Technology Co., Ltd. (a Mi Ecosystem company) Address: F10-B4, Bldg. B, International Innovation Park, 1# Keyuanweiyi Rd., Laoshan District, Qingdao, 266101, Shandong, China For further information, please go to www.mi.com Importer: Beryko s.r.o. Na Roudné 1162/76, 301 00 Plzeň www.beryko.
