- Modern Home Products Corporation Indoor Fireplace User Manual
24
Vermont Castings EWF36A
20005167
Gasket Size... ...And The Parts It Seals
3/4” The door to the front
3/4” Door to the hearth brick support
3/16” The glass seal to the door
1/2” Cat holder to top plate
1/2” Braided Damper to top plate
Should you need to change a replaceable gasket, wait
until the re is out and the stove has cooled. Be sure
to follow the standard safety procedure for working with
dusty materials: Wear safety goggles and a dust mask.
The procedure for replacing gaskets is the same,
regardless of the gasket location. Four easily-accom-
plished steps are involved:
1. Remove the existing berglass gasket by grasping
an end and pulling rmly.
2. Use a wire brush or the tip of a screwdriver to clean
the channel of any remaining cement or bits of gas-
ket.
3. Apply a thin bead of stove cement to the newly-
cleaned groove.
4. Pack a new gasket into the groove. Wait until you
have placed all but a couple inches from the end
before you trim the end to an exact t.
5. Place door back on replace, latch door and keep
closed for 1/2 hour to insure cement has set.
Remove the door by lifting it straight up off its hinge
pins. Lay it face down on a padded surface.
Follow steps 1-4 as described above.
Do not operate the replace with damaged glass door.
Use the following procedure for glass replacement.
Replace glass only with the replacement glass
made for this unit, available from your authorized
dealer.
• Remove the door and loosen the retaining clips which
hold the glass to the door frame. Remove clips. Use
caution when handling broken glass.
• Examine the gasket that seals the glass to the door
frame. Replace if necessary with gasket obtained from
your local Vermont Castings’ Authorized Dealer. See
the directions for gasket replacement on Page 23.
• Check the at surface of the door frame, and clear
away debris if necessary.
• Install the new glass.
• Secure the clips, being careful not to overtighten. Be
sure the glass is rmly seated against the gasket.
• Replace door.
Although the combustion system in the EWF36A can re-
duce creosote formation dramatically, it is not a substi-
tute for regular inspection and cleaning of the chimney
and chimney connector.
The EWF36A has been designed to reduce creosote
build-up signicantly. However, regular chimney in-
spection and maintenance must still be performed. For
safety, good stove performance, and to protect your
chimney and chimney connector, inspect your chimney
and chimney connector on a regular schedule. Clean
the system if necessary. Failure to keep the chimney
and connector system clean can result in a serious
chimney re.
When wood is burned slowly, it produces tar, organic
vapors and moisture which combine to form creosote.
The creosote vapors condense in the relatively cool
chimney ue of a slow-burning re. As a result, creo-
sote residue accumulates on the ue lining. When ignit-
ed, this creosote makes an extremely hot re within the
ue system that can damage the chimney and overheat
adjacent combustible material. If a signicant layer of
creosote has accumulated —1/8” (3 mm) or more — it
should be removed to reduce the risk of a chimney re.
If you do experience a chimney re, act promptly to:
• Close the primary air control lever and the
damper
• Get everyone out of the house.
• Call the Fire Department.
You should inspect the system every two weeks during
the heating season as part of a regular maintenance
schedule. To inspect the chimney, let the replace cool
completely. Remove the termination top. Then, using a
strong light, sight down into the chimney ue.
Clean the chimney using a specially designed brush
the same size and shape as the ue liner. Flexible
berglass rods are used to run the brush up and down
the liner, causing any deposits to fall to the bottom of
the chimney where they can be removed by removing
the catalyst housing and using a vacuum. Be sure to
vacuum the catalyst also.
If you can not do the chimney inspection yourself, con-
tact your local Vermont Castings’ Authorized Dealer, or
engage a professional chimney sweep to perform the
inspection and cleaning of the chimney.