PulsarTM EX20Rack / EX30Rack User Manual – + … – + ! … … … … % % www.mgeups.
Thank you for purchasing the EXRack Uninterruptible Power Supply. The EXRack has been designed to provide many years of trouble-free operation. Please review the manual which has been prepared to provide you with all the necessary information concerning the installation and use of your EXRack. For service call 1-800-523-0142. Sincerely, MGE UPS SYSTEMS Federal Communications Commission (FCC) Statement Note: this equipment has been tested and found to comply with Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for Models EX20Rack / EX30Rack / EXB20/30 that should be followed during installation and maintenance of the UPS batteries. c This equipment can be operated by any individual, with no previous training; c CAUTION: Risk of electric shock, even with unit disconnected from AC power source. Hazardous voltage still may be present through operation from battery.
introduction In critical situations, count on MGE UPS SYSTEMS Pulsar EX20Rack and EX30Rack uninterruptible power supplies (UPS). Their protection keeps your data intact and accessible. Pulsar EX20Rack and EX30Rack UPSs ensure top quality power around the clock, and continue operations during power failures. An intelligent microprocessor detects any operating anomalies of the UPS and triggers an alarm if corrective action is necessary.
options c Bar graph continuously indicates the battery charge level or the critical load power level; c Pulsar EX20Rack and EX30Rack are environment friendly: all components are recyclable and an electronic power-saver device reduces power consumption if the UPS is not active for a period exceeding 5 minutes while on battery back-up; c EX Driver software provides rapid startup of Pulsar EX20Rack and EX30Rack using the EX Tuner configuration module.
software supplied with Pulsar EX20Rack and EX30Rack To meet the different operating environments of your UPS, Pulsar EXRack includes 2 MGE UPS SYSTEMS software programs: c EX-Driver software for Windows c Network based Solution-PacTM power management software EX-Driver for Windows EX Driver for Windows provides communication with the UPS from a simple Windows workstation. EX-Driver is compatible with Windows 3.
general contents Pulsar EX20Rack / EX30Rack / EXB20/30 presentation Pulsar presentation ............................................................................................................................. 3 getting started / operation .......................................................................................................
Pulsar EX20Rack / EX30Rack front view Pulsar EX20Rack rear view 1e 1f 1c 2 1a 3 – + … … ! … – + … … 8 % % 11 1b 1d 10 12 13 6 9 7c 5 7b 7a 7a 3 Pulsar EXRack : 86-153500-00 MGE UPS SYSTEMS 4 Pulsar EXRack : 86-153500-00 MGE UPS SYSTEMS
Pulsar EX30Rack rear view 8 11 10 13 12 6 7c 5 9 7b 7a MGE UPS SYSTEMS Pulsar EXRack : 86-153500-00 5
Pulsar EXB20/30 Extended Battery (See options for battery extension module on page iii.
key to diagrams yellow indicator LEDs 1a to 1d flashing quickly: 2 1a overload, 1b device fault, yellow indicator LEDs 1a to 1d continuously or flashing slowly: indicate the battery charge level (if utility power present) or remaining battery time (if no utility power present). They may be on continuously or flash slowly during a transition period. By pressing the button marked "function" 2 when utility power is present, they indicate the load charge level.
technical data c output power: v Pulsar EX20Rack: v Pulsar EX30Rack: 2000VA/1400W 3000VA/2100W c input voltage: v voltage (V): a v frequency (F): 90V to 138V single phase (70V to 138V at 1/3 Power, 80V to 138V at 2/3 Power) 47Hz to 53Hz or 57Hz to 63Hz c battery: – + v type : maintenance free sealed lead-acid, 8 x 12V - 7.
Pulsar EX20Rack battery back-up time 3000 VA Pulsar EX30Rack alone 1500 VA Pulsar EX30Rack + 1 Pulsar EXB20/30 Pulsar EX30Rack + 2 Pulsar EXB20/30 750 VA 0 1 2 3 4 5 t (hours) Pulsar EX30Rack battery back-up time 2000 VA Pulsar EX20Rack alone 1500 VA Pulsar EX20Rack + 1 Pulsar EXB20/30 Pulsar EX20Rack + 2 Pulsar EXB20/30 1000 VA 500 VA 0 MGE UPS SYSTEMS 1 2 3 4 5 t (hours) Pulsar EXRack : 86-153500-00 9
10 Pulsar EXRack : 86-153500-00 MGE UPS SYSTEMS
contents getting started .................................................................................................................. 12 location ...................................................................................................................................... 12 preliminary checks .................................................................................................................... 12 connections .....................................................................
getting started location EX 30 Rack c observe the safety rules indicated at the beginning of this document. preliminary checks c check that the "on/off" button " " on the front is not pushed in; c check that rating shown on the rating label corresponds to the input voltage specification and power requirement of the load. utility power receptacle 5 7b 7a connections c connect the AC input cord to the utility power outlet.
communication option 1 c the U-Talk communication port, at the rear of the Pulsar, delivers information in the form of an RS232 series link supported by the communication protocol exclusive to MGE UPS SYSTEMS. The Solution-PacTM programs use the data made available by this protocol.
operation starting up with utility power present press button "on/off" : indicator lights test device and battery test normal operation automatic sequence: 0s 5s 7s 17 s indicating the remaining battery time percentage (here 50%) several beeps 1 s beep output off 14 output off silence your load is supported by the battery Pulsar EXRack: 86-153500-00 indicating the recharge percentage of the battery (here 50%) silence UPS is on utility power MGE UPS SYSTEMS
starting up with out utility power press "on/off" button: indicator lights test device and battery test normal operation on battery automatic sequence: 0s 5s 7s 17 s indicating the remaining battery time percentage (here 50%) several beeps 1 s beep output off MGE UPS SYSTEMS output off 3 s beep your load is supported by the battery Pulsar EXRack: 86-153500-00 indicating the remaining autonomy percentage (here 50%) 1 beep every 10 s UPS is on utility power 15
operation on battery no utility power break in utility power warning alarm at low battery 0 mn Pulsar switches off automatically x + ε mn x mn indicating the remaining battery time: here, between 75 and 87% 1 beep every 10 s your load is supported by the battery 1 beep every 3 s you have less than 12% battery time remaining: power down your load, Pulsar will soon switch off automatically return of utility power silence UPS output "off" load charge percentage At whatever point the utility power ret
overload operating anomalies utility power present device fault 1 beep every second automatic load transfer to bypass no utility power present battery fault A battery test is carried out while Pulsar, is in start-up mode, then automatically every 7 days (interval times adjustable using EX Driver).
18 Pulsar EXRack: 86-153500-00 MGE UPS SYSTEMS
service and factory repair - call 1 - 800 - 523 - 0142 c direct questions about the operation, repair, or servicing of this equipment to MGE UPS SYSTEMS, Inc. Customer Support Services. Include the part number, and serial number of the unit in any correspondence. Should you require factory service, contact MGE UPS SYSTEMS, Inc. Customer Support Services and obtain a Return Materials Authorization (RMA) prior to shipping your unit.
MGE UPS SYSTEMS, Inc. www.mgeups.
