Installation manual
34003905EN/AA
The Network Management Card (66102) can be hot-plugged on all
UPSs from MGE UPS SYSTEMS equipped with a Minislot. It is not
necessary to shutdown the UPS, disconnect the load or restart the
UPS.
◗ Remove the plastic cover of the Minislot.
◗ Note the MAC address of the card before inserting it.
◗ Insert and secure the card with the screws.
◗ Connect the ETHERNET cable.
◗ Check the ETHERNET port indications.
◗ Wait until the UPS Data LED flashes regularly (approx. two minutes),
indicating that card start-up has terminated correctly.
Note. Connection detection continues until the card has been
connected to the network. Once connection is made, card start-up
continues.
Once the card has started, proceed as indicated below.
◗
Connect one end of the cable (34003918) to the Service port.
◗
Connect the other end of the cable to the COM (IOIOI) port of a PC.
◗
Run a terminal emulator such as HyperTerminal
TM
:
>Bits per second: 9600 Data bits: 8
>Parity: none Stop bits: 1
>Flow control: none
>"Echo typed characters locally" option: disabled
◗
Type MGEUPS or mgeups, then press the
↵
key.
The main configuration menu is displayed.
Your network is equipped with a BOOTP/DHCP server
◗
The card is configured by default with this service enabled.
◗ No manual configuration is required.
◗
The IP parameters are automatically collected by the card.
◗
To view the IP parameters, enter 2 (Network configuration), then enter
1 (Read Network settings).
The settings supplied by the server are displayed.
◗
Note the IP address.
◗
To exit this function, enter 3, then 5 (Exit).
Your network is not equipped with a BOOTP/DHCP server
◗ Manual configuration is required.
◗
In the main menu, enter 2 (Network configuration), then again 2
(Modify Network settings).
◗
Follow the instructions and enter the IP parameters.
◗
Wait until "Done" is displayed, indicating that the IP parameters have
been saved.
◗
Return to the main menu and enter 1 (Reset). The card restarts with
the new IP settings (after approx. two minutes).
To check whether the
Network Management Card
is operational after
installation and configuration, proceed as follows.
◗ Run a browser and enter in the address bar:
http://IP address/ (e.g. http://172.17.21.141/)
◗ The home page is displayed.
◗
Set the time by clicking the Time command.
◗
Continue configuration via the sections in the Settings menu.
This manual provides all the information required to install and
configure the
Network Management Card
.
For more information on the supervision, control and configuration
functions offered by the
Network Management Card
, see the user
manual on the
Solution-Pac 2
CD-ROM or in the Products/Power
Management section of the
www.mgeups.com
site.
INSTALLATION
IP SETTINGS
-----------------------------------------------------------------------------------------
MGE UPS SYSTEMS
NETWORK MANAGEMENT CARD
------------------------------------------------------------------------------------------
1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
5 : Exit
------------------------------------------------------------------------------------------
Network configuration :
Mode : DHCP
MAC address : 000623001C07
IP address : 172.17.23.18
Subnet mask : 255.255.248.0
Gateway : 172.17.17.1
66
102
Se
ttin
gs
/S
e
ns
or
E
T
HE
R
N
ET
1
0
0
M
1
0
M
U
P
S
d
a
ta
R
S
2
3
2
O
n
=
Li
n
k
B
l
in
k
=
A
c
t
ETHERNET
ASI
------------------------------------------------------------------------------------------
1 : Read Network settings
2 : Modify Network settings
3 : Exit
------------------------------------------------------------------------------------------
For each of the following questions, you can press "Return" to select
the value shown in braces, or you can enter a new value.
Should this target obtain IP settings from the network?[N] N
Static IP address [172.17.16.16]? 172.17.21.141
Subnet mask IP address [255.255.0.0]? 255.255.255.0
Gateway address IP address [0.0.0.0]? 172.17.17.1
Done
ACCESS TO SUPERVISION
USER MANUAL