OPERATORS AND PARTS MANUAL NO. 07-2-V-FORCE V- FORCE TWIN EXPELLER SUPER SPREADER MODEL: 7400 7500 US PATENT NO. 5,368,236 5,501,404 DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD. Manufactured by County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 www.meyermfg.com E-mail: sales@meyermfg.
This Page Intentionally Blank Model V-Force —2—
TABLE OF CONTENTS TABLE OF CONTENTS ..........................................................................................................................................3 MANUFACTURER’S WARRANTY .........................................................................................................................4 INTRODUCTION.....................................................................................................................................................5 SAFETY PRECAUTIONS .......
NEW MEYER SUPER SPREADER Jan. 1, 1996 MANUFACTURER’S WARRANTY I. The “Product Registration & Inspection Certificate” along with the original billing invoice “Owners Registration Form” must be completed in full and promptly returned to Meyer Mfg. Corp. for this warranty to become both valid and effective. All warranties on New Meyer Super Spreaders shall apply only to the original retail customer from an authorized Meyer Mfg. Corp. dealership. II.
INTRODUCTION Congratulations on your purchase of a new Meyer farm equipment product. Undoubtedly you have given much consideration to your purchase and we’re proud that you have selected Meyer. Pride in craftsmanship, engineering and customer service have made Meyer products the finest in the farm equipment industry today. There is no substitute for quality. That is why thousands of people like you have purchased Meyer farm equipment.
SAFETY PRECAUTIONS This symbol is used to call attention to instructions concerning personal safety. Be sure to observe and follow these instructions. Take time to be careful! WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
SAFETY FIRST A brief definition of signal words that are used in this manual is as follows: CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It is also used to alert against unsafe practices. DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
SAFETY FIRST The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the spreader. DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION.
PRE-OPERATION WARNING: BEFORE OPERATING, READ THIS OWNERS MANUAL COMPLETELY. PAY PARTICULAR ATTENTION TO THE “SAFETY PRECAUTIONS” AND “SAFETY FIRST” PAGES. READ ALL SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL. This spreader is to be operated with 540 RPM PTO only, unless the spreader is 1000 RPM equipped. The hitch of the spreader is designed for a standard tractor drawbar. Adjust the drawbar at 13 to 17 inches above the ground.
TRANSPORTING TRACTOR TOWING SIZE REQUIREMENTS Use the following chart for calculating the minimum tractor weight. HYDRAULIC HOSES MODEL SPREADER EMPTY WEIGHT + LOAD = GW SV2636 6,100 + _____ = _____ SV3245 7,640 + _____ = _____ SV3954 8,650 + _____ = _____ JACK SV7400 8,040 + _____ = _____ FIGURE 2.
Operating speed is dictated by the terrain over which you are traveling. Always use caution. Avoid traveling on slopes or hills that are unsafe. WARNING: OBSERVE ALL APPLICABLE TRAFFIC LAWS WHEN TRANSPORTING ON PUBLIC ROADWAYS. CHECK LOCAL LAWS FOR ALL HIGHWAY LIGHTING AND MARKING REQUIREMENTS. WARNING: INSTALL A SMV EMBLEM ON REAR OF SPREADER FOR TRANSPORTING ON ROADWAYS AND KEEP THIS EMBLEM CLEAN AND BRIGHT. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Clean all manure from rear ends of augers, flow control rear gate and spinners. WARNING: MAKE CERTAIN EVERYONE IS CLEAR OF THE SPREADER BEFORE APPLYING POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. Slowly engage the PTO. Operate the spreader several minutes to clean manure scrapings and to allow any remaining manure and the spreader to freeze dry. Hydraulically run the flow control rear gate up and down to clean gate slide guides.
OPERATION LOADING UNLOADING CAUTION: TO PREVENT DAMAGE TO AUGERS, SPINNERS, AND DRIVE LINES, FOREIGN OBJECTS (STONES, CONCRETE, TIMBER, METAL OR LARGE FROZEN CHUNKS OF MANURE) SHOULD NEVER BE LOADED INTO THE SPREADER. WARNING: MAKE CERTAIN EVERYONE IS CLEAR OF SPREADER BEFORE APPLYING POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DANGER: NEVER ENTER THE SPREADER BOX FOR ANY REASON WITHOUT FIRST DISCONNECTING PTO SHAFT FROM TRACTOR. DO NOT ALLOW OTHERS IN THE BOX.
VERY IMPORTANT: THIS MACHINE IS NOT INTENDED TO BE A BALE GRINDER, HAY CHOPPER OR BEDDING MACHINE. LONG HAY OR STRAW MUST CONTAIN MANURE IN ORDER TO BE SPREAD. FAILURE TO COMPLY MAY DAMAGE THE DRIVETRAIN AND VOID THE WARRANTY. RESULT IN SPREADER DAMAGE OR SERIOUS PERSONAL INJURY. The rear spinners have been designed and tested to provide the best spread pattern for most liquids and semi solid manure. However, the pattern will vary for each specific condition.
side at a time. After first side is unloaded install bolts in opposite side and unload the remainder of the spreader. If a second shear has happened without obstruction in the auger, install the next larger size shear bolt. As the shear bolt size is increased the protection on the machine is going to decrease. The potential for equipment damage is greater. Order replacement bolts and nuts from the chart below. Part # 831-5020-1.75 884-5020 831-5618-1.
PTO DRIVE LINE WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY ALL SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
3. Adjust the drawbar at 13-17” above the ground. Extend or shorten the drawbar so horizontal distance from end of tractor PTO shaft to center of hitch pin hole is 14” for 540 RPM 1-3/8-6 spline, (16” for optional 1000 RPM 1-3/8-21, 20” for 1000 RPM 1 3/4- 20 spline). Secure the drawbar so the hitch pin hole is located directly below the PTO drive line. PTO adapters are not recommended as damage to the drive line may occur. A hitch pin with a minimum diameter of 1” and bottom retaining pin is recommended.
ADJUSTMENTS WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. SPINNER MATERIAL GUIDES Regularly inspect and adjust two spinner material guides located at both the LR and RR of the spreader. Create a 1/8 - 3/8” clearance between material guides and spinner teeth, figure 7. Maintain the recommended clearances for maximum spreading pattern.
IDLER NYLON ROLLER RH AUGER SPROCKET The RH auger chain drive, figure 10, is automatically tensioned by a spring loaded idler NYLON roller. The extension spring should extend 3/4" from its neutral 4" total length. SPRING LOADED ADJUSTER Manual adjustment for the automatic tensioning idler, NYLON roller assembly is located at the right front lower corner of the spreader tank. ROLLER CHAIN FIGURE 10.
LUBRICATION WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DAILY LUBRICATION (every 8-12 loads) L1 Grease (2) rear spinner lower bearings. These bearings are grease line fitted to the LR frame channel of the spreader. L2 Keep the reservoir tank full of new 30 weight oil for chain lubrication.
MONTHLY LUBRICATION L12 Keep the (3) gearboxes ½ full of liquid gear grease at all times, capacity approximately 30 oz. Check regularly for any observable leakage. If leakage is excessive, replace required input/output shaft seals as needed. Lubricate with a “Semi-Fluid, EP Lithium Base, Gear Grease”. L13 Clean and repack the wheel hubs with axle grease annually. Grease hub through zerk in hub monthly. Be careful not to over grease and force seal out of back side of hub.
LUBRICATION & ADJUSTMENT FOR 3RD AUGER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OF DEATH. A1 COVER L2 L1 WEEKLY LUBRICATION (every 25-30 loads) ) L1 Grease (1) bearing supporting the front shaft of the 3rd auger assembly. This bearing is grease line fitted to the spreader front, bearing back plate.
INSTRUCTIONS FOR AUTOMATIC CHAIN OILER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. directly on top of sprockets. Adjust brush holders so oiler brushes are pushed down into the roller chain approximately ½”. Carefully tighten up the ½”-20 nuts on the oiler brushes. DO NOT over tighten as damage to the brush will occur.
This Page Intentionally Blank Model V-Force —25—
REPAIR PARTS OIL-KIT 35 Model V-Force —26—
OIL-KIT KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PART NO.
FRONT SHIELD & SIDE SHAFT DRIVE KEY PART NO. 1 914-3801 2 910-0013 3 4 5 6 7 8 9 10 11 12 13 DESCRIPTION 1-3/8" Pillow Block Bearing 80B18 Sprocket 1-3/8" Bore, 5/16" Keyway 935-0002 5/16x5/16x2-1/4" Hardened Key 923-3837 SV7500 Front Side Shaft 925-3882 Side Shaft Tightener Assy.
AUGER DRIVE, PRIMARY REDUCTION KEY PART NO. 1 933-3628 2 3 4 5 5A 5B 6 7 8 DESCRIPTION Copper Tube Grease Line 25" (includes zerk, fittings) 38-0013 Roll Pin, 5/16" x 1-3/4" 925-3883-1 First Reduction Tightener Assembly Arm Weldment 808-.75-1.
AUGER DRIVE, SECONDARY REDUCTION KEY 1 2 3 4 5 6 6A 6B 7 8 9 10 11 12 13 14 15 16 17 Model V-Force PART NO. 14-0031 38-0013 910-0063 851-7510-3Z 911-0018 912-0013 912-0013-1 912-0013-2 808-.75-1.25-14 925-3884-1 813-3118-Z 933-3804 30-0002 929-0003 808-1-1.
RH AUGER DRIVE, FINAL REDUCTION Install (#120-56) Roller Chain, Key #13 W/Connector Link Cotter Pins Facing Towards Front Of Spreader. KEY PART NO. 1 33-0025 2 910-0064 3 910-0101 831-5020-1.75 884-5020 831-5618-1.75 884-5618 910-0028 4 5 813-3118-Z 933-3804 6 913-3801-1 Model V-Force DESCRIPTION 2-1/2" Retaining Ring Welded Sprocket Assy, LH, 80A60x120A9 Shear Sprocket Assy.
LH AUGER DRIVE, FINAL REDUCTION Install (#120-72) Roller Chain, Key #21 W/Connector Link Cotter Pins Facing Towards Rear Of Spreader.
LH AUGER DRIVE, FINAL REDUCTION KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20A 20B 21 21A 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Model V-Force PART NO. 14-0031 925-3873 910-0064 808-.75-1.25-14 30-0014 30-0002 925-3846-2 851-7510-6Z 925-3870-1 914-3807A 925-3833 913-3801-1 813-7510-Z 933-3621 925-3841 29-0009 925-3885-1 925-3843 925-3839 912-0014 912-0014-1 912-0014-2 911-0024 911-0026 912-0001 925-3838 925-3842 910-0101 831-5020-1.75 884-5020 831-5618-1.
BOX, AUGERS & SIDE SHAFT Model V-Force —34—
BOX, AUGERS & SIDE SHAFT KEY 1 2 3 4 5 6 7 8 9 10 11 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28a 29 30 31 32 33 34 35 36 37 PART NO.
UNLOADING GATE & TRIP PAN DOORS PRIOR TO 08 S/N’S PRIOR TO 08 S/N’S PRIOR TO 08 S/N’S Model V-Force —36—
UNLOADING GATE & TRIP PAN DOORS KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 PART NO.
SPINNERS & GEARBOX SHAFT DRIVE PADDLE OPTIONS Model V-Force —38—
SPINNERS & GEARBOX SHAFT DRIVE KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Model V-Force PART NO. 901-3753-10 901-3753-19 19-0041 935-0002 937-0014-1 19-0042 19-0043 901-3906 901-3907 914-3604 901-3906-6 901-3753-20 901-3907-1 937-0009-2 937-0009-3 808-1.38-2.5-14 808-1.38-2.5-18 808-1.38-2.5-10 901-3855-4 851-6311-2Z 815-6311-Z 921-0001 850-6311-1.
SPINNER GEAR REDUCERS USE FLUID GEAR GREASE ONLY. DO NOT USE GREASE FOR LUBRICANT. Model V-Force KEY 1 2 3 4 5 8 9 10 11 12 13 PART NO.
HUBS, AXLE & TANDEM AXLE ASSEMBLY KEY PART NO.
THIRD AUGER Model V-Force —42—
THIRD AUGER KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Model V-Force PART NO. 929-3601 35-0008 910-0050 14-0031 925-3866 911-0033 35-0010 910-0005 925-3861 926-5000 933-3606 913-3805 925-3865 955-3809 933-3627 933-3804 925-3825 813-3118-Z 851-6311-2Z 814-6311-Z DESCRIPTION Extension Spring ½"x1/2"x2" Square Key 80B26 Sprocket 2" Bore, ½" Keyway Bearing, 4-Bolt Flange, 2" B Chain Tightener Bracket Wldmt. #80-36 Roller Chain w/Connector.
918-0212 PTO DRIVE SHAFT ASSEMBLY (PRIOR TO SERIAL #SV087500201) 918-0312 PTO DRIVE SHAFT ASSEMBLY (SERIAL #SV087500201 & LATER) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80 DEGREE C.V.) KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MEYER PART NO.
(PRIOR TO SERIAL #SV087500201) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80 DEGREE C.V.) KEY 1 2 3 4 5 6 7 8 NS NS MEYER PART NO. 918-0208-2-3-2 918-0208-2-3-3 918-0208-2-3-4 918-0208-2-3-5 918-0208-2-3-6 918-0208-2-3-7 918-0208-2-3-1 918-0208-2-3-8 918-0208-2-3-9 918-0208-2-3-11 DESCRIPTION Housing Hub Spring Pack 1900NM Washer Retaining Ring Sealing Ring Clamp Cone Assembly Cam Bushing-In Item #2 Shim Kit (SERIAL #SV087500201 & LATER) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80 DEGREE C.V.
1000 RPM KIT SVS-RPM-KIT KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 NS NS NS PART NO. 19-0002-17 29-0015 33-0012 33-0021 33-0039 35-0010 805-0031-Z 806-0031-Z 851-3118-.75Z 910-0005 911-0045-HD 912-0010 914-3809 914-3816 914-3817 923-3834 923-3835 925-3890-1 925-3891-1 925-3892-10 925-3892-1 925-3892-9 933-3812 955-3809 808-1.5-2.
918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80 DEGREE C.V.) PRIOR TO 08 SERIAL NOS. NOTE: PTO IS 4" SHORTER THEN STANDARD 540 OR 1000 RPM PTO KEY 1 MEYER PART NO.
918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) CUTOUT CLUTCH PRIOR TO 08 SERIAL NOS. KEY 1 2 3 4 5 6 7 8 NS NS MEYER PART NO.
918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE S.P. (STANDARD) 918-0311 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80 DEGREE C.V.) SERIAL NOS. 08 AND LATER NOTE: PTO IS 4” SHORTER (1-3/4 20) 6” SHORTER (1-3/8 21 THEN STANDARD 540 OR 1000 RPM PTO SEE NEXT PAGE FOR CUTOUT CLUTCH KEY MEYER PART NO.
918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE S.P. (STANDARD) 918-0311 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) CUTOUT CLUTCH SERIAL NOS. 08 AND LATER KEY 1 2 3 4 5 6 7 8 NS NS MEYER PART NO.
V-MAX HIGHWAY LIGHTING 15 KEY PART NO. 1 56-0030 1a 56-0030-TR 2 2a 56-0031 56-0031-TR 3 56-0032 4 56-0004 5 5a 5b 6 7 8 9 56-0005 56-0012 56-0005-1 56-0008 56-0009 65-0006-5 925-3876 925-3793 Model V-Force DESCRIPTION Dual Light LH w/4-Plug Truck Mount Dual Light LH w/4-Plug Dual Light RH w/4-Plug Truck Mount Dual Light RH w/4-Plug Ag Light Harness W/Module #1232 4-Way Socket 4-Pin Coil Cable Assy.
MEYER SUPER SPREADER “TROUBLE SHOOTING” SYMPTOM AUGERS Augers shake or chatter PROBLEM Stiff roller chains - dry Loose roller chains Worn sprockets/chains Dry auger trough SOLUTION Lubricate roller chains Tighten roller chains Replace sprockets/chains Load auger trough w/manure Augers wobble/lift up & down Wor n auger shaft bushings Replace auger shaft bushings Worn auger hold down nylon Replace auger hold down bearings nylon bearings FLOW CONTROL GATE GEAR BOXES Will not lift No hydraulic supply Fr
MEYER SUPER SPREADER “TROUBLE SHOOTING” SYMPTOM ROLLER CHAINS AND SPROCKETS PROBLEM Excessive chain wear Lack of lubrication Out of alignment/loose Lubricate/align/tighten Roller chain breakage Loose roller chain Worn sprockets Tighten roller chains Replace sprockets Sprocket teeth tipped over Worn roller chain Bad roller bearings SPINNERS (PADDLES/TEETH) SOLUTION Replace roller chain Replace bearings Spinners turn hard/squeak Bad lower spinner bearings Replace lower spinner bearings Shake at hi
MEYER SUPER SPREADER “MAINTENANCE RECORD” Model No. ____________________Serial No.
MEYER EQUIPMENT WHEEL TORQUE BOLT/STUD SIZE ½ 9/16 5/8 3/4 SOCKET SIZE 3/4 7/8 15/16 1-1/16 1-1/8 / 1-1/2 PRESS FORMED WHEEL CENTER 80 ft lbs 80 ft lbs 100 ft lbs BOLT TYPE Lug Bolt Lug Bolt Bevel or Flange Nut Flange Nut TIRE INFLATION TIRE SIZE 11L-15 12.5L-15 12.5L-15 14L-16 16.5L-16 19LX16.1 21.5L-16.1 11R/22.5 425/65X22.
Farm Equipment Buyers Trust the Name Meyer! MEYER SUPER SPREADER “SPECIFICATIONS” V-Force 7400 Trailer Model V-Force 7400 Truck Mount CAPACITY 400 1,870 / 250 V-Force 7500 Trailer Model V-Force 7500 Truck Mount 500 2,433 / 324 500 2,433/324 9.26 DIMENSIONS 18’ 4” plus front drive 15’ 51 ½” plus truck ht. 12 12 21’ 9” 15’ 78” w/19Lx16.1 76.5” w/16.5Lx16.1 85” w/19Lx16.1 83.5 w/16.5Lx16.1 18’ 4” plus front drive 15’ 60 ½” plus truck ht.
Thickness Front/Back Panel Frame Construction Door Opening Spindle Diameter-tandem axle Hub Splash Shields – front & rear Transport Light Kit V-Force 7400 Trailer Model 3/16” V-Force 7400 Truck Mount 3/16” V-Force 7500 Trailer Model 3/16” V-Force 7500 Truck Mount 3/16” Heavy 8” channel 27” x 42” 2 ¾” Heavy 8” channel 27” x 42” N/A Heavy 8” channel 27” x 42” 3” sleeved Heavy 8” channel 27” x 42” N/A 8 bolt Standard – flat N/A Standard – flat 8 bolt – Heavy Duty Standard - angled N/A Standard - an
This Page Is Intentionally Blank Model V-Force —58—
Manufactured by: Meyer Mfg. Corp. County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425-0405 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 www.meyermfg.com E-mail: sales@meyermfg.
c
