OPERATOR’S AND PARTS MANUAL NO. PB-SV MEYER V-MAX TWIN EXPELLER SUPER SPREADER MODEL: 2636 3245 3954 US PATENT NO. 5,368,236 5,501,404 DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD. MANUFACTURED BY Meyer Mfg. Corp. 6990633 (1-13) 3/2015 574 West Center Avenue P.O. Box 405 Dorchester, Wisconsin 54425-0405 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 www.meyermfg.com E-mail: sales@meyermfg.com Printed in U.S.A.
INTRODUCTION Congratulations on your purchase of a new Meyer equipment product. Undoubtedly you have given much consideration to your purchase and we’re proud that you have selected Meyer. Pride in craftsmanship, engineering and customer service have made Meyer products the finest in the farm equipment industry today. There is no substitute for quality. That is why thousands of people like you have purchased Meyer farm equipment.
PRE-DELIVERY & DELIVERY CHECK LIST Meyer Manufacturing Corporation Spreader Check List Phone: 715-654-5132 • Toll-Free: 1-800-325-9103 • P.O. Box 405 • Dorchester, WI 54425 This Pre-Delivery & Delivery Check List must be gone through by the Selling Party and the Customer to validate the Owner’s Registration Form. PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST After the New Meyer Spreader has been completely set-up, check to be certain it is in correct running order before delivering it to the customer.
Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.
TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HOW TO READ YOUR SERIAL NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRE-DELIVERY & DELIVERY CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 MANUFACTURER’S WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT SHIELD & SIDE SHAFT DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 AUGER DRIVE, PRIMARY REDUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 AUGER DRIVE, SECONDARY REDUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 RH AUGER DRIVE, FINAL REDUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 LH AUGER DRIVE, FINAL REDUCTION . . . . . . . . . . . .
#918-0150 VERTICAL DRIVELINE, TRUCK MOUNT MECHANICAL DRIVE . . . . . . . . . . . . 76 OPTIONAL TRUCK GEARBOX DRIVE PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 WHEEL TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 TIRE INFLATION . . . . . . . . . . . . . . . . . . . . . . .
MANUFACTURER’S WARRANTY MEYER SUPER SPREADER 11 / 2014 I. The “Owner's Registration Form” must be completed in full and promptly returned to Meyer Mfg. Corp. for this warranty to become both valid and effective. All warranties on new Meyer Super Spreaders shall apply only to the original retail customer from an authorized Meyer Mfg. Corp. dealership. II.
SAFETY PRECAUTIONS This symbol is used to call attention to instructions concerning personal safety. Be sure to observe and follow these instructions. Take time to be careful! WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
SAFETY FIRST A brief definition of signal words that are used in this manual is as follows: DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury and includes hazards that are exposed when guards are removed. CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury.
SAFETY DECALS The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the spreader. DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION.
SAFETY DECALS The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the spreader. DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION. WARNING NOT A STEP! This is a PTO Guard.
PRE-OPERATION WARNING: BEFORE OPERATING, READ THIS OWNER’S MANUAL COMPLETELY. PAY PARTICULAR ATTENTION TO THE “SAFETY PRECAUTIONS” AND “SAFETY FIRST” PAGES. READ ALL SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL. This spreader can be purchased as either 540 RPM or 1000 RPM Model. Do not operate 540 RPM implements at 1000 RPM or 1000 RPM implements at 540 RPM. No PTO adapter may be used to alter speed or geometry.
TRANSPORTING TRACTOR TOWING SIZE REQUIREMENTS Use the following chart for calculating the minimum tractor weight. HYDRAULIC HOSES HOSE BRACKET MODEL SV2636 PTO SHAFT SV3245 SV3954 HITCH JACK FIGURE 2. SPREADER HOOKUP Route hydraulic hoses through the hose support rod which is mounted to the hitch frame, figure 2. Connect the hydraulic hoses for the flow control rear gate to the tractor’s double acting valve hydraulic system. Move the tractor hydraulic controls to observe proper flow gate operation.
MAXIMUM SPREADER LOAD WEIGHTS Model 2636 3245T Maximum Gross Weight (Pounds) 12,000 24,000 Total Net Weight (Pounds) 6,100 7,640 Cubic Foot Capacity** 181 227 Capacity in Gallons 1,355 1,694 **Struck capacity, heaped loads have significantly higher capacities. 3954T 32,000 8,650 272 2,033 Operating speed is dictated by the terrain over which you are traveling. Always use caution. Avoid traveling on slopes or hills that are unsafe.
The chain must be of adequate size to hold the weight of the loaded spreader (See table on page 14). See your ag cart or wagon owner/operator's manual and parts book, which is also available at www.meyermfg.com. If using a grab hook at the end(s) of the chain to secure the chain to itself, a hook latch must be installed. The length of the safety chain is not to be any longer than necessary to turn without interference. If any chain links or attachment hardware are broken or stretched, repair before using.
OPERATION LOADING UNLOADING CAUTION: TO PREVENT DAMAGE TO AUGERS, SPINNERS, AND DRIVE LINES, FOREIGN OBJECTS (STONES, CONCRETE, TIMBER, METAL OR LARGE FROZEN CHUNKS OF MANURE) SHOULD NEVER BE LOADED INTO THE SPREADER. WARNING: MAKE CERTAIN EVERYONE IS CLEAR OF SPREADER BEFORE APPLYING POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DANGER: NEVER ENTER THE SPREADER BOX FOR ANY REASON WITHOUT FIRST DISCONNECTING PTO SHAFT FROM TRACTOR. DO NOT ALLOW OTHERS IN THE BOX.
The rear spinners have been designed and tested to provide the best spread pattern for most liquids and semi solid manure. However, the pattern will vary for each specific condition. The factors that contribute most to differing patterns will be moisture content and the amount and length of bedding material. For most typical conditions, the spread pattern should be uniform and about 15 ft. wide.
Order replacement bolts and nuts from the chart below. Prior to Serial Number SV123954243 and Later 46-7500-5 and Part # 831-5020-1.75 884-5020 831-5618-1.75 884-5618 Description 1/2”-20 x 1-3/4” Allen Head Cap Bolt 1/2”-20 Top Locknut Grade 8 9/16”-18 x 1-3/4” Allen Head Cap Bolt 9/16”-18 Top Locknut Grade 8 910-0101 120B33 Shear Sprocket Assembly Complete FIGURE 6.
PTO DRIVE LINE WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY ALL SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Adjust the drawbar at 15-22” above the ground. Extend or shorten the drawbar so horizontal distance from end of tractor PTO shaft to center of hitch pin hole is 14” for 540 RPM 1-3/8-6 spline, (16” for optional 1000 RPM 1-3/8-21, 20” for 1000 RPM 1 3/420 spline). Secure the drawbar so the hitch pin hole is located directly below the PTO drive line. PTO adapters are not recommended as damage to the drive line may occur. A hitch pin with a minimum diameter of 1” and bottom retaining pin is recommended.
ADJUSTMENTS WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. SPINNER MATERIAL GUIDES Effective w/08 serial numbers Regularly inspect and adjust two spinner material guides located at both the LR and RR of the spreader. Create a 1/8 - 3/8” clearance between material guides and spinner teeth, figure 10.
FRONT DRIVE ROLLER CHAINS There are five roller chain drives located at the front of the spreader. Regularly check that all tensioning springs are in serviceable condition for automatic roller chain tightening. Manually adjust spring tensioners (as needed) by turning double locknuts on all tensioning bolt/idler assemblies. Proper roller chain tension is when 1/4” to 1/2” deflection occurs on the slack side of the chain. Regularly re-check all roller chain tensions.
IDLER NYLON ROLLER SPRING LOADED ADJUSTER RH AUGER CHAIN DRIVE, SPRING LOADED TIGHTENER The RH auger chain drive, figure 13, is automatically tensioned by a spring loaded idler NYLON roller. The extension spring should extend 3/4” from its neutral 4” total length. Manual adjustment for the automatic tensioning idler, NYLON roller assembly is located at the right front lower corner of the spreader tank. ROLLER CHAIN FIGURE 13.
LUBRICATION WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DAILY LUBRICATION (every 8-12 loads) L1 Grease (2) rear spinner lower bearings. These bearings are grease line fitted to the LR frame channel of the spreader. L2 Oil (5) roller chain drives regularly at the front of spreader with light weight machine oil.
MONTHLY LUBRICATION L13 L12 Keep the (3) gearboxes 1/2 full of liquid gear grease at all times, capacity approximately 30 oz. Check regularly for any observable leakage. If leakage is excessive, replace required input/output shaft seals as needed. Lubricate with a “Semi-Fluid, EP Lithium Base, Gear Grease”. Clean and repack the wheel hubs with axle grease annually. Grease hub through zerk in hub monthly. Hub from factory has bearings packed but hub is not fully loaded with grease.
LUBRICATION & ADJUSTMENT FOR OPTIONAL 3RD AUGER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. A1 COVER L2 L1 purpose. (Seal cover tight with silicone when reinstalling.) WEEKLY LUBRICATION (every 25-30 loads) L1 Grease (1) bearing supporting the front shaft of the 3rd auger assembly.
LUBRICATION FOR OPTIONAL TRUCK MOUNT MECHANICAL DRIVE SYSTEM WARNING: DISENGAGE PTO POWER SOURCE, REMOVE KEY, AND RELIEVE HYDRAULIC PRESSURE BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. L1 L2 L1 MONTHLY LUBRICATION L1 L2 Grease PTO drive line (2) places with lithium grease every 8 hours. Keep the upper and lower gearboxes 1/2 full of 75W90 Synthetic oil, capacity approximately 30 oz.
INSTRUCTIONS FOR OPTIONAL AUTOMATIC CHAIN OILER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. The automatic chain oiler attachment gives a squirt of clean oil to all roller chains every time that the spreader’s rear gate, hydraulic cylinder is activated.
REPAIR PARTS FRONT SHIELD & SIDE SHAFT DRIVE PB-SV - 30 -
FRONT SHIELD & SIDE SHAFT DRIVE KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 22a 23 24 25 PB-SV PART NO. 914-3801 910-0013 935-0002 923-3828 923-3829 923-3830 925-3882 46-3600-12 46-3600-14 33-0044 912-0001 925-3882-1 911-0035 911-0060 808-150-300-10 910-0015 910-0099 808-1.5-2.25-10 813-3118-Z 808-1-1.5-18 933-3804 925-3822-6 929-0003 38-0013 955-3703 925-5006-1 924-3821 924-3827 924-3827-RPM 32-0018-1 924-3826 924-3820 808-1.25-1.
AUGER DRIVE, PRIMARY REDUCTION PB-SV - 32 -
AUGER DRIVE, PRIMARY REDUCTION KEY 1 2 3 3A 3B 4 5 5A 5B 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PB-SV PART NO. 933-3628 38-0013 925-3883-1 925-5015-1 925-5017 925-5017-3 808-.75-1.25-14 912-0012 912-0012-1 912-0012-2 851-7510-2Z 925-3717-3 911-0032 911-0072 910-0039 910-0033 910-0005 914-3602 925-3606 925-3883 925-5015 931-3810 923-3833 923-3833-XL 910-0063 910-0063-RPM 813-3118-Z 933-3804 925-3822-6 929-0003 808-1-1.
AUGER DRIVE, SECONDARY REDUCTION PB-SV - 34 -
AUGER DRIVE, SECONDARY REDUCTION KEY 1 2 3 4 5 6 6A 6B 7 8 9 10 11 12 13 14 15 16 17 18 PB-SV PART NO. 14-0031 38-0013 910-0063 910-0063-RPM 851-7510-3Z 911-0018 911-0073 912-0013 912-0013-1 912-0013-2 808-.75-1.25-14 925-3884-1 925-3884-1-RPM 813-3118-Z 933-3804 925-3822-6 929-0003 808-1-1.
RH AUGER DRIVE, FINAL REDUCTION Install (#120-56) Roller Chain, Key #13 W/Connector Link Cotter Pins Facing Towards Front Of Spreader.
RH AUGER DRIVE, FINAL REDUCTION KEY 1 2 3 4 5 6 7 8 9 10 10A 10B 11 12 13 14 15 16 17 18 19 20 PB-SV PART NO. 33-0025 910-0064 910-0064-RPM 910-0028 910-0101 831-4420-1.75 884-4420 831-5020-1.75 884-5020 831-5618-1.75 884-5618 910-0105 831-5013-1.75 884-5013 831-5020-1.75 884-5020 831-5013-1.75 884-5013 831-5020-1.75 884-5020 813-3118-Z 933-3804 913-3801-1 913-3705 925-3834 925-5011 933-3621 808-.75-1.25-14 912-0013 912-0013-1 912-0013-2 925-3848-7 929-3601 911-0023 851-7510-3.
LH AUGER DRIVE, FINAL REDUCTION Install (#120-72) Roller Chain, Key #21 W/Connector Link Cotter Pins Facing Towards Rear Of Spreader.
LH AUGER DRIVE, FINAL REDUCTION KEY PART NO. 1 14-0031 2 925-3873 925-3873-RPM 3 910-0064 910-0064-RPM 4 808-.75-1.25-14 5 925-3846-2 6 851-7510-6Z 7 925-3870-1 8 914-3807A-IND 9 925-3833 925-5010 10 913-3801-1 913-3705 11 813-7510-Z 12 933-3621 13 925-3841 14 29-0009 15 925-3885-1 16 925-3843 17 925-3839 18 912-0014 18A 912-0014-1 18B 912-0014-2 19 911-0024 19A 911-0026 20 912-0001 21 925-3838 22 925-3842 23 910-0028 910-0101 831-4420-1.75 884-4420 831-5020-1.75 884-5020 831-5618-1.
BOX, AUGERS & SIDE SHAFT (1 of 2) PB-SV - 40 -
BOX, AUGERS & SIDE SHAFT (1 of 2) KEY 1 2 3 3A 4 4A 5 6 7 8 9 10 11 11A 11B 11C 11D 12 13 14 PB-SV PART NO. (2636) 901-3803 929-3801 956-3803 956-3803-1 955-3611 55-0013 955-3609 955-3805 933-3602 926-3801-5 926-3813 926-3825 PART NO. (3245) 901-3802 929-3801 956-3803 956-3803-1 955-3611 55-0013 955-3609 955-3806 933-3602 926-3801-5 PART NO.
BOX, AUGERS & SIDE SHAFT (2 of 2) PB-SV - 42 -
BOX, AUGERS & SIDE SHAFT (2 of 2) KEY 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 PB-SV PART NO. (2636) 901-3830-5 851-5013-1.25Z 810-5013-Z 901-3816-30 901-3830-5 901-3830-8 914-3801 937-0002 923-3828 923-3827 955-3833 803-3816-1.5Z 35-0017 844-3816-Z 926-3802-2 926-3801-2 924-3822 924-3823 33-0025 933-3802 933-3801 933-3801-NSM-09 PART NO. (3245) 901-3830-5 851-5013-1.
UNLOADING GATE & TRIP PAN DOORS (1 of 2) PB-SV - 44 -
UNLOADING GATE & TRIP PAN DOORS (1 of 2) KEY PART NO.
UNLOADING GATE & TRIP PAN DOORS (2 of 2) PB-SV - 46 -
UNLOADING GATE & TRIP PAN DOORS (2 of 2) KEY PART NO. 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 PB-SV 925-3898-2 925-3921-1 925-3898-3 815-1008-Z 805-0010-Z 823-25-2Z 901-3801-76 925-5016-1 808-1.5-2.
SPINNERS & GEARBOX SHAFT DRIVE PB-SV - 48 -
SPINNERS & GEARBOX SHAFT DRIVE KEY 1 2 3 4 5 6 7 8 8a 8b 9 9a 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PB-SV PART NO. 901-3834-1 901-3835-1 19-0041 851-5013-1.5Z 828-0050-Z 806-0050-Z 935-0002 937-0014-1 19-0042 851-5013-1.5Z 828-0050-Z 806-0050-Z 19-0043 19-0048 851-5013-1.5Z 828-0050-Z 806-0050-Z 901-3856-1 901-3897-1 901-3856-3 901-3855-5 901-3855-1 901-3896-1 901-3855-1-14 914-3604 851-5013-1.5Z 810-5013-Z 901-3855-8 924-3817 924-5011 924-3818 111-0060-18-CC 808-1.
SPINNER GEAR REDUCERS USE FLUID GEAR GREASE ONLY. DO NOT USE GREASE FOR LUBRICANT. Meyer #48-0055-GAL / 48-0055-QT Mobilux EP23 KEY PART NO.
19-0047 UPPER GEARBOX - TRUCK USE 75W90 SYNTHETIC OIL ONLY. MEYER PART #48-0066. CAPACITY 30 OZ. KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 PB-SV PART NO. 19-0047-1-PF 19-0018-2 19-0018-3 19-0016-3 19-0018-4 19-0041-1 19-0041-2 19-0024-20 19-0016-5 19-0023-2 19-0002-17 19-0041-3 19-0018-7-PF DESCRIPTION Splined Pinion Output Shaft/Gear Assy.
#19-0038-SYN 2:1 RATIO GEARBOX LOWER GEARBOX - TRUCK USE 75W90 SYNTHETIC OIL ONLY. MEYER PART #48-0066. CAPACITY 30 OZ. KEY 1 2 3 4 5 6 7 8 9 10 11 12 PB-SV PART NO.
This Page Intentionally Blank PB-SV - 53 -
HUBS, AXLE & TANDEM AXLE ASSEMBLY PB-SV - 54 -
HUBS, AXLE & TANDEM AXLE ASSEMBLY KEY PART NO. (M 3954) PART NO.
V-MAX HIGHWAY LIGHTING PB-SV - 56 -
V-MAX HIGHWAY LIGHTING KEY PART NO.
OPTIONAL THIRD AUGER Items 10 and 11 are used on two auger units only.
OPTIONAL THIRD AUGER KEY PART NO. DESCRIPTION 1 929-3601 Extension Spring 2 35-0008 1/2” x 1/2” x 2” Square Key 3 910-0050 80B26 2” B, 1/2” Keyway 4 14-0031 Bearing, 4-Bolt Flange, 2" B 5 925-3866 Chain Tightener Bracket Wldmt. 6 911-0033 #80-36 Roller Chain w/Conn.
OPTIONAL OIL - KIT PB-SV - 60 -
OPTIONAL OIL - KIT KEY PART NO. DESCRIPTION 0 SV-OIL-KIT Oil Kit For V-Max Spreader 1 952-0001-1-33 Holder, Manifold Valve Assembly 2 952-0001-1-27 Sleeve Nut Brass 3 952-0001-1-28 5/32” Brass Ferrule 4 952-0001-1-9 One Way Valve (Schrader Valve) 5 952-0001-1-11 Bearing, 7/16” Stainless 6 952-0001-1-10 Screen Flat Oiler .
918-0312 PTO DRIVE SHAFT ASSEMBLY (SERIAL #SV042636206 & LATER) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80° C.V.
918-0312 PTO DRIVE SHAFT ASSEMBLY (SERIAL #SV042636206 & LATER) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80° C.V.) KEY 1 2 3 4 5 5A 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 PART NO.
540 RPM 1-3/8 - 6 SPLINE YOKE WWE2480 (80° C.V.) KEY PART NO.
1000 RPM ADD-ON KIT SVS-RPM-KIT KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 19-0002-17 29-0015 33-0012 33-0021 33-0039 935-0003 805-0031-Z 806-0031-Z DESCRIPTION Vent Plug Tightener Spring Retaining Ring 1-1/4” Retaining Ring 1-1/2” Expansion Plug 3/8 x 3/8 x 1-1/2” Key Rd Ends 5/16” Flat Washers 5/16” Internal Tooth Lock Washers 851-3118-.
918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80° C.V.) PRIOR TO 08 SERIAL NUMBERS WITH 1000 RPM ADD-ON KIT NOTE: PTO IS 6" SHORTER THAN STANDARD 540 OR 1000 RPM PTO.
918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80° C.V.) PRIOR TO 08 SERIAL NUMBERS WITH 1000 RPM ADD-ON KIT KEY MEYER PART NO.
918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80° C.V.) CUTOUT CLUTCH PRIOR TO 08 SERIAL NUMBERS WITH 1000 RPM ADD-ON KIT KEY 1 2 3 4 5 6 7 8 NS NS PB-SV MEYER PART NO.
This Page Intentionally Blank PB-SV - 69 -
918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8”, 21 SPLINE S.P. (STANDARD) 918-0311 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/4”, 20 SPLINE (OPTIONAL) WWE2480 (80° C.V.) SERIAL NUMBERS 08 AND LATER WITH 1000 RPM ADD-ON KIT NOTE: PTO IS 4” SHORTER (1-3/4” x 20) 6” SHORTER (1-3/8” x 21 THAN STANDARD 540 OR 1000 RPM PTO.
918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8”, 21 SPLINE S.P. (STANDARD) 918-0311 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/4”, 20 SPLINE (OPTIONAL) WWE2480 (80° C.V.) SERIAL NUMBERS 08 AND LATER WITH 1000 RPM ADD-ON KIT KEY MEYER PART NO.
918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8”, 21 SPLINE S.P. (STANDARD) 918-0311 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/4”, 20 SPLINE (OPTIONAL) CUTOUT CLUTCH SERIAL NUMBERS 08 AND LATER WITH 1000 RPM ADD-ON KIT KEY 1 2 3 4 5 6 7 8 NS NS MEYER PART NO.
This Page Intentionally Blank PB-SV - 73 -
918-0308 PTO DRIVE SHAFT ASSEMBLY 1-3/8” 21 SPLINE S.P. (FACTORY BUILT 1000 RPM, NOT KIT EQUIPPED) WWE2480 (80° C.V.) 918-0310 PTO DRIVE SHAFT ASSEMBLY 1-3/4” 20 SPLINE S.P. (OPTIONAL) (FACTORY BUILT 1000 RPM, NOT KIT EQUIPPED) WWE2480 (80° C.V.
918-0308 PTO DRIVE SHAFT ASSEMBLY 1-3/8” 21 SPLINE S.P. (FACTORY BUILT 1000 RPM, NOT KIT EQUIPPED) WWE2480 (80° C.V.) 918-0310 PTO DRIVE SHAFT ASSEMBLY 1-3/4” 20 SPLINE S.P. (OPTIONAL) (FACTORY BUILT 1000 RPM, NOT KIT EQUIPPED) WWE2480 (80° C.V.) KEY MEYER PART NO.
#918-0150 VERTICAL DRIVELINE, TRUCK MOUNT MECHANICAL DRIVE KEY 1 2 3 4 5 6 7 8 PB-SV PART NO. 918-0150-1-1 618-0001-2-2 918-0208-1-6 918-0208-2-1 918-0240-1-1 918-0150-2-1 918-0230-2-2-T 618-0001-1-2 DESCRIPTION 18 Ga. Profile Tube Inboard Yoke 2a Lemon Profile Spring Pin 10 x 80 Cross & Bearing Kit Clamp Yoke 2400 1-3/8 6 Spline AGKF Profile And Sleeve WA Hub Yoke w/Key 1-3/8” Bore, 5/16” Key Inboard Yoke 1b Lemon Profile - 76 - QTY.
OPTIONAL TRUCK GEARBOX DRIVE PACKAGE #SV-GBD NOTE: If rotation is oppposite of expected, flip gearbox to have opposite end of shaft go into knuckle. KEY PART NO. DESCRIPTION QTY.
MEYER SUPER SPREADER TROUBLESHOOTING AUGERS FLOW CONTROL GATE GEAR BOXES MATERIAL GUIDES PTO SHAFT PB-SV SYMPTOM PROBLEM SOLUTION Augers shake or chatter Stiff roller chains - dry Loose roller chains Worn sprockets/chains Dry auger trough Lubricate roller chains Tighten roller chains Replace sprockets/chains Load auger trough w/manure Augers wobble/lift up & down Worn auger shaft bushings Worn auger hold down nylon bearings No hydraulic supply Froze tight Replace auger shaft bushings Replace
MEYER SUPER SPREADER TROUBLESHOOTING ROLLER CHAINS AND SPROCKET SPINNERS (PADDLES/TEETH) SYMPTOM PROBLEM SOLUTION Excessive chain wear Lack of lubrication Out of alignment/loose Lubricate/align/tighten Roller chain breakage Loose roller chain Worn sprockets Tighten roller chains Replace sprockets Sprocket teeth tipped over Worn roller chain Bad roller bearings Bad lower spinner bearings Replace roller chain Replace bearings Replace lower spinner bearings Spinner bent/out of balance Straighten
WHEEL TORQUE BOLT/STUD SIZE SOCKET SIZE 5/8 15/16 1-1/16 1-1/8 1-1/2 3/4 PRESS FORMED WHEEL CENTER 100 ft lbs NA BOLT TYPE Bevel or Flange Nut Flange Nut TIRE INFLATION TIRE SIZE 12.5L-15 14L-16 16.5L-16 19LX16.1 11R/22.5 425/65X22.
FARM EQUIPMENT BUYERS TRUST THE NAME MEYER! Meyer Super Spreader SPECIFICATIONS MODEL 2636 Bushels Gallon Cubic Foot Weight Overall Height with 14L tire(add 1-1/2 inches for 16.5L tire) Tank Length Overall Width (no tires) Overall Width w/14L Tank Steel (copper bearing) Frame construction (channel) Spindle Size Hub Size Expeller Size Expeller Speed Auger Speed Tractor PTO Speed (Max.) Auger Diameter Overall Length 3rd Auger 260 (no ht. ext.) 1355 181 5300 lbs. MODEL 3245 360 320 (with ht. ext.) (no ht.
This Page Intentionally Blank PB-SV - 82 -
MAINTENANCE RECORD MODEL NO. ____________________________________ DATE SERVICE PERFORMED SERIAL NO. ____________________________________ DATE Manufactured by: Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.
Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.
