Form 1-915 R3 November 2011 Installation Instruction and Owners Manual BLASTER SALT/SAND SPREADERS Models: 350/350S/750/750R/750S & 750RS BLASTER 750(33000) 750R(33750) 750S (39000) 750RS (39010) BLASTER 350 (32000) 350S (37000) Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifications and prices without notice or without incurring any obligation. Meyer Products LLC 18513 Euclid Ave.
TABLE OF CONTENTS INTRODUCTION ................................................................................................. 1 VEHICLE REQUIREMENTS ................................................................................ 1 SAFETY GUIDELINES ........................................................................................ 2 350 & 350S PARTS LIST ..................................................................................... 3 INSTALLING RECEIVER MOUNT MODEL: 350/350S/750R/750RS.....
INTRODUCTION This manual will assist you in the proper set-up, installation, and use of the Blaster series spreaders. Please read and understand the contents of the manual completely (especially all safety information) before attempting any procedure contained herein. The Blaster line of spreaders may be attached to many types of vehicles to suit different spreading needs. The modular design allows for multiple mounting variations using the same spreader.
SAFETY GUIDELINES For you safety when the word WARNING is used, this refers to information that if not carefully followed could result in personal injury or death. The word CAUTION refers to a situation that could cause minor injury or damage to equipment. WARNING – Before operating READ and UNDERSTAND this operators manual in its entirety. WARNING – NEVER operate equipment while under the influence of alcohol, drugs, or medications that might impair your judgment and reaction time.
Blaster 350/350S 4 6 22 32 5 34 33 Note: Auger Extension (16) must be removed when using salt only. If it is not removed this may cause the motor to stall.
INSTALLING RECEIVER MOUNT MODEL: 350/350S/750R/750RS The Blaster 350/350S/750R/750RS is a dedicated, Class 3, receiver (hitch) mount salt spreader. Prior to installation, be certain that the vehicle receiver is in good working order, is rated for at least a 500 lb. tongue load, and is fastened to the vehicle securely. CAUTION - The spreader is a large heavy item that should be installed with an assistant.
Blaster 750/750S 4 21 5 28 6 30 29 2 3 1 7 33 Note: Auger Extension (15) must be removed when using salt only. If it is not removed this may cause the motor to stall.
Blaster 750R & 750RS 4 21 28 6 5 30 29 2 3 1 33 7 34 15 36 20 25 16 27 18 25 14 13 19 10 11 27 22 36 27 34 26 36 24 17 10 27 26 19 23 27 23 37 35 26 38 27 22 11 8 12 11 21 23 9 To Speed Control Red 32 Mounting Bracket Red Blue White Ground Red White Red Pigtail 31 Red To Battery To Spreader Motor Black Parts List 750R 750RS Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 750R 750RS Part No. Part No. Qty.
ELECTRICAL INSTALLATION FOR ALL BLASTER SERIES SPREADERS 1.) Locate the wire harness and begin to route it from the rear of the vehicle to the front. The molded rubber plug indicates the rear of the harness, closest to the spreader. Use frame holes and frame supports as lashing points. Do not attach to fuel or brake lines. Avoid wire-runs along exhaust system or hot engine parts. Melting damage to the harness can occur in the proximity of extreme heat. 2.) Mount the rubber plug under the rear bumper.
OPERATING THE SPREADER Before using the spreader read and understand all aspects of this operators manual. PREPARATION CAUTION – Sweep area clear of foreign objects or obstacles that could cause personal injury. Keep other persons and animals out of area to be spread. SPREADER LOADING Your spreader will come equipped with a cover that will protect your de-icing material from rain or snow; this can be removed simply by detaching the holding clamps on the sides of the hopper.
SPREADER MAINTENANCE WARNING – Disconnect power to spreader before servicing. CAUTION – Do not attempt to service control unit. It is a solid-state electronic device and has no user serviceable parts; any attempt to do so will void warranty. CAUTION - The electric motor is sealed and should not be taken apart for any reason. Disassembly of the motor will void warranty. CAUTION – When replacing parts use only Meyer Products approved parts or risk voiding warranty.
MEYER BLASTER SPREADER WARRANTY Meyer Products, LLC, warrants to the original purchaser of Meyer® brand products that they will be free from defects in materials or workmanship, with the exceptions stated below. No person is authorized to change this warranty or to create any additional warranty on Meyer® products. This warranty runs for a period of two years from the date of purchase on any purchase of a complete Blaster Spreader Package. If the Package is registered on-line at www.meyerproducts.