WingMan™ For use with Wingman moldboards Operation and Maintenance Manual 1
Thank you... Thank you for buying your Meyer Plow. As a new owner of hard-working, mechanical equipment, we strongly urge you to spend quality time with this owner’s manual. It’s easy to use and full of time-saving tips that will enhance your ownership experience. It includes suggestions for faster installation, safe operation and more productive plowing. We also strongly urge you to register your new Meyer plow at meyerproducts.com.
STEP UP TO A 5-YEAR WARRANTY When you purchase and register* any Meyer snow plow, it will be covered for a full five years. If you do not register the plow, it will be covered for two years. * Must register your complete plow system online to activate 5 year warranty.
Registration Data Sheet Register your snowplow at www.meyerproducts.com Once registered, you will be given a Registration ID.
Table of Contents Registration Data Sheet................................................................... Inside Cover Safety Definitions & Warnings .........................................................................2-3 Introduction................................................................................................................4 EC Declaration of Conformity ..............................................................................5 WingMan Component Identification................
Safety Definitions & Warnings 1 SAFETY DEFINITIONS ! 2 This is the safety alert symbol. It is used to alert you to!potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury ! DANGER or!death. 3 !!! WARNING DANGER Indicates an imminently hazardous situation ! DANGER which, if not avoided, will result in death or serious injury.
Safety Definitions & Warnings ! 16 17 18 19 20 ! DANGER ! ! WARNING DANGER ! CAUTION ! WARNING !CAUTION ! ! !! CAUTION DANGER DANGER !CAUTION ! WARNING ! DANGER ! WARNING !! CAUTION ! WARNING ! CAUTION CAUTION DANGER !! CAUTION CAUTION ! WARNING !CAUTION DANGER !! CAUTION 21 22 23 24 25 26 WARNING !CAUTION !! DANGER ! CAUTION ! WARNING DANGER !!CAUTION ! CAUTION ! WARNING ! DANGER ! CAUTION ! CAUTION ! WARNING DANGER ! CAUTIO
Introduction Snow, despite the beauty it may impart to a bleak winter landscape, poses the dual threat of inconvenience and danger. The environmental conditions associated with snow, not to mention the health hazards and economic loss it may impose, seriously endanger thousands of lives annually. Business and industry suffer, and millions of snowbelt residents may be affected by a single snowstorm.
EC Declaration of Conformity CE DECLARATION OF CONFORMITY The undersigned representing the manufacturer and the authorized representative established within the community Meyer Products LLC 18513 Euclid Ave Cleveland, OH 44112 herewith declared that product: Drive Pro / Lot Pro / Road Pro / Diamond Edge / Super-V / Super-V2 / Path Pro / Path Pro 2 / Power Box Model/Type ref: is in conformity with the Essential requirements of the following EC Directives when subject to correct installation, maintenance,
WingMan Component Identification 6
WingMan Component Identification 1. Moldboard – Steel or Polyethylene moldboard sheet is impact and corrosion resistant. 7. Power Angling Cylinders – Heavy-duty winter specified hydraulics to move the plow left or right. 2. Cutting Edge – Replaceable high carbon steel provides extra long operating life; should be 1/2" above ground in plowing position. (Can be higher when used on gravel driveways.) Available in Urethane or Rubber. 8.
Pistol Grip Controller 23047 The snow plow should only be in operation when the vehicle ignition switch and the control switch are in the “ON” position. Care should be taken to insure that the control switch is kept dry and free from moisture during normal operation. When operating the snow plow lights the vehicle headlight switch must be turned to the park position so the vehicle headlights and snow plow lights are not on at the same time.
Hands-Free Plowing or ALM/ARM Meyer re-branded the ALM/ARM feature on its 23047 controllers to be Hands-Free Plowing (HFP) ™. When activated, the Hands-Free Plowing (HFP) mode uses the vehicle’s shift lever to control the up/down movement of the moldboard. Pressing the HFP button on the controller will toggle you through: On/Off, Back-drag Mode (default mode when active), and Forward Plowing Mode.
Controller Troubleshooting The Controller offers diagnostics imprinted on the backside of the controller for easy identification of which solenoid or coil may be creating the error. Systems Monitor LED Read-Out Light Flashes Check Coil (wire Color) Continuous Light----Motor Solenoid 1 Light Flash----Red 2 Light Flashes----Black 3 Light Flashes----Green 4 Light Flashes----Yellow 5 Light Flashes----Lt.
2" Receiver Mounting System – Dismount/OFF 1 1. Press down button until Float light turns Blue/on. 2 2. Push lift arm down until there is a little slack in the chain. 3 4. Attach crankstand to a-frame.. 3. Remove crankstand from lift frame. 5 4 7 5. Adjust crankstand until crankstand comes into contact with the ground and then turn 1 to 2 revolutions. 8 ! ! 7. Disconnect both electrical plugs and install weather cover on both ends. SAFETY PRECAUTIONS - See pages 2-3 for definitions ! 8.
2" Receiver Mounting System – Mount/On 2 1 1. Push the plow towards the vehicle using the wheels. 2. Align the 2" receiver and mount the plow using the pin to lock it in place. 3 3. Adjust crankstand until until it is no longer in contact with the ground. 4 4. Remove crankstand from a-frame. 6 5 ! 5. Attach crankstand to lift frame. SAFETY PRECAUTIONS - See pages 2-3 for definitions 6. Remove weather covers and connect ! both electrical plugs.
E-73 HYDRAULIC COMPONENT IDENTIFICATION A G H F L Key: I K A: Filler Hole & Relief Valve B: “B” Solenoid (Red) C: Left Angle Cylinder Connection D: Right Angle Cylinder Connection D E: “C” Solenoid (Green) F: “A” Solenoid (Black) G: Crossover Relief Valve H: Lift Cylinder Connection I: “B” Check Valve J: Drain Plug K: Motor Solenoid L: Drop Speed Adjustment J C E B 13
E-73 Hydraulics – Testing Tips Before any troubleshooting is started, make certain the following conditions are met. 1. The moldboard is pointing straight ahead. If the unit is disabled, this can often be done by connecting the hose from the left cylinder into the right cylinder and pushing the snow plow by hand. 2. Check to ensure the power angling cylinders are installed correctly. 3.
E-73 Hydraulics Troubleshooting Guide These charts are intended to be used as an aid in diagnosing Meyer Hydraulic Power Units. They are not a substitute for factory training and experience. Be certain to read the General Information and Testing Tips sections before attempting any troubleshooting. Additional detailed information as well as all electrical schematics may be found in Service Manuals @ www.MeyerProducts.com.
E-73 Hydraulics Troubleshooting Guide These charts are intended to be used as an aid in diagnosing Meyer Hydraulic Power Units. They are not a substitute for factory training and experience. Be certain to read the General Information and Testing Tips sections before attempting any troubleshooting. Additional detailed information as well as all electrical schematics may be found @ www.MeyerProducts.com. CONDITION POSSIBLE CAUSE CORRECTION Plow will not hold in angled position 1.
General Maintenance – Wingman Adjust spring tension (paper should slide between coils) Check all bulbs for operation Grease once/year *6” tall when new Cutting edge wear* Grease pins with white lithium Check for tightness/leaks of hydraulic connections ! ! ! SAFETY PRECAUTIONS - See pages 2-3 for definitions ! DANGER See pages 24-29 for more detailed explanation of maintenance steps ! DANGER ! DANGER ! WARNING ! CAUTION ! WARNING ! WARNING 6/9/10/12/13/14/16/17/18 ! CAUT
General Maintenance Tightening the Trip Spring and Adjusting the Eye Bolt To properly adjust the Trip Springs, tighten the top locknut 4 (four) complete rotations beyond the point that the coils begin to separate. Tighten the bottom locknut to hold eyebolt in position. It is important that each eye bolt is locked in this position to work properly when the moldboard experiences tripping action. Greasing the Pivot pins and King bolt Use a grease gun to grease pivot pins and king bolt.
General Maintenance prevent corrosion from occurring. Also check the electrical connections to assure they’re tight and corrosion free. Make sure that all wires are being held clear from moving or hot engine parts or from sharp sheet metal. For maximum efficiency, the battery, alternator, and regulator must be in top operating condition to assure maximum electrical output. Adjusting the Drop Speed The rate at which the plow is lowered is adjustable.
Pre-Season Maintenance Visit www.MeyerProducts.com for a complete list of your plow system maintenance items! Protects your electrical system with Meyer winter formula dielectric grease. Meyer Products LLC recommends this maintenance information for regular service. Sustained heavy operation may call for more frequent service. Snow plowing subjects a vehicle to exceptionally rugged use. As a result, it is very important to inspect and bring the snow plow and vehicle up to maximum operating conditions.
Pre-Season Maintenance Check the Diagnosis chart, pages 17-20 and Pre/Post Season Maintenance, pages 26-28, for advice on maintaining the unit. 1. Check and maintain hydraulic fluid reservoir level to Full. Oil level should be checked with lift ram down or retracted position. 2. Check entire hydraulic system for leaks. A significant drop in hydraulic fluid level is evidence of a leak which must be corrected to prevent serious damage. 3.
Post-Season Summer Maintenance Visit www.MeyerProducts.com for a complete list of your plow system maintenance items! 1. Draining & Replacing Meyer M-1 Hydraulic Fluid Drain the fluid by removing the drain plug located on the bottom of unit. To drain the fluid from the power angling cylinders, disconnect the fittings and completely retract the cylinder rods and purge cylinders and hoses of all hydraulic fluid.
Snow Plow Storage Visit www.MeyerProducts.com for a complete list of your plow system maintenance items! 1. When snow plow is disconnected, disconnect lift chains from lift arm and extend lift cylinder to end of stroke and coat chrome rod with light grease. This fills the cylinder with hydraulic fluid and protects the interior and exterior from rust and corrosion. 2.
Meyer® Snow Plows Limited Warranty What is Covered: Meyer Products, LLC, warrants to the original purchaser of Meyer® brand products that they will be free from defects in materials or workmanship, with the exceptions stated below. No person is authorized to change this warranty or to create any additional warranty on Meyer® products. How Long Coverage Lasts: This warranty runs for a period of two years from the date of purchase on any purchase of a complete Snow Plow Package1.
Meyer® Snow Plows Limited Warranty The original purchaser’s sole and exclusive remedy against Meyer Products and its Distributors and SubDistributors, and Meyer Products’ sole obligation for any and all claims, whether for breach of contract, warranty, tort (including negligence) or otherwise shall be limited to providing, through its authorized Distributor/ Sub-Distributor network, all labor and/or parts necessary to correct such defects free of charge.
It pays to keep your Meyer ALL Meyer. Meyer Genuine Parts are designed to fit properly and perform better and last longer – which means you save money by replacing fewer parts less often. In addition, all Meyer Genuine Parts: ❯ ❯ ❯ ❯ Comply with Meyer specifications and technical standards Maintains the warranty on your original equipment Fit perfectly and reduces installation time Guarantee original equipment quality Look for the Meyer name on all your replacement parts.
Meyer Products carries a full line of spreaders and other products including: Broadcast Spreaders If you are looking for a heavy-duty broadcast spreader for all-season use, look no further. Tailgate Spreaders Dump Truck Getting a good return on your dump truck is important. That’s why we make the very best Under Tailgate Spreaders (UTG) and Replaceable Tailgate Spreaders (RTG) available.
