Use and Care Manual

ManualsBrandsMeyer&Cross ManualsFlush Mount Ceiling LightsHenri 10 in. Brass Semi-Flush Mount with Clear Glass Shade

SEMI-FLUSH MOUNT CEILING LIGHT

Save these instructions

CARE INSTRUCTIONS:

• Turnlightoandallowbulbtocoolbeforecleaning.

• Carefullywipecleanwithasoft,dryclothorstaticduster.

• Alwaysavoidtheuseofharshchemicalsorabrasivecleanersastheymay



causedamagetothexture’snish

Made in China

SF0806SF0807SF0808SF0809SF0810rev011221EFSME1A

Removethextureandthemountingpackagefromthebox

andmakesurethatnopartsaremissingbyreferencingthe

illustrationsontheinstallationinstructions.

IMPORTANT SAFETY INSTRUCTIONS:

• CAUTION –TURN OFF THE MAIN POWER AT THE

CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE,

IN ORDER TO PREVENT POSSIBLE SHOCK.

• CAUTION –If you feel you do not have enough electrical wiring experience contact a

qualiﬁed licensed electrician for installation of your lighting ﬁxture.

• Theseinstructionsareprovidedforyoursafety.Please read carefully and completelybefore

beginningtheassemblyandinstallationofthislightingxture.

• Donotusetheelectriccordonly(withoutsteel/reinforcedcable)tosupporttheweightofthe

lightingxture.

• Thislightingxtureisintendedforindooruseonly,andindrylocations.

• Thislightingxtureisintendedforceilingmountonly,andconnectedonlyto3-wire,

single-phaseelectricalsupplysystemwithproperGroundwireorsystem.

• ForusewithE26(medium)baselightbulbsonly.

• Toavoidtheriskofre,donotexceedthemaximumwattageof60W incandescent bulb ,

or 9W LED bulb , or 13W ﬂuorescent (CFL) bulb , or 9W self-ballasted LED bulb .

(Bulbsnotincluded)

WARNINGS:

• Toreducetheriskofre,electricalshock,orpersonalinjury:alwaysturnothislightingxture

andallowittocoolbeforeattemptingtoreplacethelightbulb.

• Donottouchlightbulbwhilextureisturnedon.

• Keepammablematerialsawayfromthislightingxture.

• Neverlookdirectlyatalitbulb.

Summary of content (6 pages)

PAGE 1
SEMI-FLUSH MOUNT CEILING LIGHT Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions. Save these instructions IMPORTANT SAFETY INSTRUCTIONS: • CAUTION – TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE, IN ORDER TO PREVENT POSSIBLE SHOCK.
PAGE 2
Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware. 1. Feed wires through the mounting bracket (A). 2. Securely connect wires as shown using wire connectors. Connect white to white, black to black, and connect the green or copper ground wire to the mounting plate ground as shown. A B 3. Secure mounting bracket (A) to the ceiling mount using long screws (B). B 4.
PAGE 3
PLAFONNIER À MONTAGE SEMI-FLUSH Sortir le luminaire et le nécessaire de fixation de l’emballage et consulter les illustrations dans les instructions d’installation pour vérifier qu’il ne manque aucune pièce. Conservez ces instructions CONSIGNES DE SÉCURITÉ ESSENTIELLES : • ATTENTION – SECTIONNER L’ALIMENTATION AU NIVEAU DU DISJONCTEUR AVANT D’INSTALLER LE LUMINAIRE, AFIN D’ÉCARTER LE RISQUE DE CHOC ÉLECTRIQUE.
PAGE 4
Ne mettez aucun élément de contenu au rebut avant de terminer l’assemblage au complet, afin d’éviter de jeter accidentellement de petites pièces ou un élément de quincaillerie. 1. Faites passer les fils à travers la plaque de fixation (A). 2. Raccordez solidement les fils à l’aide de connecteurs à fils tel que l’illustre la figure ci-contre.
PAGE 5
LÁMPARA DE TECHO DE SEMI EMPOTRADO Extraiga el artefacto y el paquete de montaje de la caja y asegúrese de que no falten piezas verificando con las ilustraciones de las instrucciones de montaje. Guarde estas instrucciones INSTRUCCIONES IMPORTANTES DE SEGURIDAD: • PRECAUCIÓN - ANTES DE INSTALAR EL ARTEFACTO CORTE LA ALIMENTACIÓN ELÉCTRICA PRINCIPAL EN EL DISYUNTOR PARA EVITAR POSIBLES DESCARGAS ELÉCTRICAS.
PAGE 6
No deseche nada hasta después de haber terminado de ensamblar para evitar botar por accidente piezas pequeñas o herramientas. 1. Pase los cables a través de la placa de montaje (A). 2. Conecte los cables en forma segura con conectores para cable, tal como se muestra. Conecte blanco con blanco, negro con negro y el cable verde o cobre de descarga a tierra a la descarga a tierra de la placa de montaje tal como se muestra. A B 3. Asegure la placa de montaje (A) al techo con tornillos largos (B). B 4.