Operating instructions
Table Of Contents
- Operating instructions
- Operating instructions in a nutshell
- Contents
- 1 Getting to know L/L-S balances line
- 2 Startup
- 3 Weighing
- 4 Menu
- 4.1 Overview
- 4.2 Menu operation
- 4.3 Description of menu options
- 4.3.1 Reset or recording of balance settings (1st menu option “RESET”)
- 4.3.2 Functions (2nd menu option / see Section 5 for their use)
- 4.3.3 Weighing mode (3rd menu option)
- 4.3.4 Weighing unit 1 (4th menu option “UNIT 1”)
- 4.3.5 Weighing unit 2 (5th menu option “UNIT 2”)
- 4.3.6 Autozero (6th menu option / see overview and notes in Section 4.1)
- 4.3.7 Auto shut off
- 4.3.8 Peripheral unit (8th menu option / see overview and notes in Section 4.1)
- 4.3.9 Send mode (9th menu option / see overview and notes in Section 4.1)
- 4.3.10 Send format (10th menu option / see overview and notes in Section 4.1)
- 4.3.11 Baud rate (11th menu option / see overview and notes in Section 4.1)
- 4.3.12 Bit/Parity (12th menu option / see overview and notes in Section 4.1)
- 4.3.13 Handshake (13th menu option / see overview and notes in Section 4.1)
- 5 Functions
- 6 Technical data, options, optional equipment
- 7 Appendix
Appendix
31
English
Error/Error message Cause Rectification
Overload ➞ Remove sample from weighing pan, zero
again (tare).
Underload ➞ Check whether weighing pan is
positioned properly.
No stability
• in taring or adjusting (calibration) ➞ Wait for stability before pressing key.
• when reference weight for piece counting ➞ Ensure more stable ambient conditions.
is placed on pan ➞ Remove weighing pan and clean if
necessary
Wrong adjustment weight on pan or none at all ➞ Place required adjustment weight in
centre of pan.
Reference weight (Piece counting, Percent ➞ Increase reference weight.
weighing, Plus-minus weighing) too small
Internal fault ➞ Contact METTLER TOLEDO customer
service.
Wrong weighing pan or pan missing or ➞ Place correct pan or empty pan on
not empty balance.
Adjustment aborted with the «C» key
No display
• AC adapter not plugged in ➞ Check AC power supply.
Plug AC adapter into power supply.
• Batteries discharged (only with compact ➞ Replace batteries; if using rechargeables
models) connect instrument to AC power supply.
7.3 Connecting L/L-S balances to other METTLER TOLEDO devices
Device Connecting cable settings/
Remarks
Titrators:
DL31, 36, 38 RS9–RS9 (m/f) send continous
DL50, 53, 55, 58 11101051
MTCom-Bus 310 RS9–RSopen (m/-)
21900640
SQC 14 RS9–RS9 (m/f)
(statistical quality control) 11101051
Spider (industrial scale) RS9–RS9 (m/m)
Viper BC (industrial scale) 21252588
LC-PVolume (pipette calibration) RS9–RS9 (m/f) AX balances recommended
11101051
LC-PCalc RS9–RS9 (m/f)
11101051
LC-P45 (application printer) RS9–RS9 (m/f)
11101051
GA42 (report printer) RS9–RS9 (m/f)
11101051
íååååì
7.2 What if ...?
î____ï
Error 1
Error 2
Error 3
0.000
g
Abort
Error 4