Operating instructions
Table Of Contents
- Operating instructions
- Operating instructions in a nutshell
- Contents
- 1 Getting to know L/L-S balances line
- 2 Startup
- 3 Weighing
- 4 Menu
- 4.1 Overview
- 4.2 Menu operation
- 4.3 Description of menu options
- 4.3.1 Reset or recording of balance settings (1st menu option “RESET”)
- 4.3.2 Functions (2nd menu option / see Section 5 for their use)
- 4.3.3 Weighing mode (3rd menu option)
- 4.3.4 Weighing unit 1 (4th menu option “UNIT 1”)
- 4.3.5 Weighing unit 2 (5th menu option “UNIT 2”)
- 4.3.6 Autozero (6th menu option / see overview and notes in Section 4.1)
- 4.3.7 Auto shut off
- 4.3.8 Peripheral unit (8th menu option / see overview and notes in Section 4.1)
- 4.3.9 Send mode (9th menu option / see overview and notes in Section 4.1)
- 4.3.10 Send format (10th menu option / see overview and notes in Section 4.1)
- 4.3.11 Baud rate (11th menu option / see overview and notes in Section 4.1)
- 4.3.12 Bit/Parity (12th menu option / see overview and notes in Section 4.1)
- 4.3.13 Handshake (13th menu option / see overview and notes in Section 4.1)
- 5 Functions
- 6 Technical data, options, optional equipment
- 7 Appendix
Functions
17
English
Requirement
The function “F count” must be activated in the menu (Section 4).
➞ Place empty container on the balance and tare by briefly pressing the
«
##
##
#» key.
Setting the reference: a reference weight must first be entered for piece counting:
➞ Add a number of reference pieces to container. Possible numbers are 5, 10, 20,
50, 100 and “no” (piece counting deactivates).
Note that the minimum weight = 10d (d: display increment), and the minimum
unit weight = 1d!
➞ Hold the «F» key down until “SEt ... PCS” is displayed.
➞ Repeatedly press the «
““
““
“» key until the display equals the number of
reference pieces entered.
➞ Confirm the number of reference pieces with the «
±±
±±
±» key or automatic
acceptance after 7 seconds. The current number of pieces (PCS = pieces) is
displayed.
Switching between piece count and weight display
➞ Place the items to be counted in the container. The number of pieces is
displayed.
➞ Press the «
““
““
“» key. The weight is displayed (in unit 1, and if the key is pressed
again, in unit 2, provided this function is activated).
➞ Return to the piece count display by pressing the «
““
““
“» key again.
5 Functions
Settings and values saved under a given function are retained until they are replaced or another function is selected. The «C» key
can be used to cancel the procedure currently in progress.
5.1 Piece counting
0.00 g
SEt 10
PCS
##
##
#
F
SEt 20
PCS
20
PCS
240
PCS
144.81 g
““
““
“
±±
±±
±
““
““
“
5.2 Percent weighing
Requirement
The function “F 100 %” must be activated in the menu (Section 4).
Set target weight
➞ Target weight (Reference weight, which corresponds to 100 %) in centre of
pan.
Note that the minimum weight = 10d (d: display increment).
➞ Hold the «F» key down until “SEt 100 %” is displayed.
➞ Press the «
““
““
“» key to select “SEt 100 %” or “SEt no %” (Percent weighing
deactivated).
➞ The «
±±
±±
±» key can be used briefly to confirm or automatic acceptance after 7
seconds.
0.00 g
148.50 g
SEt100
100.00
F
±±
±±
±
%
%