Operating instructions
Table Of Contents
- Operating instructions
- Operating instructions in a nutshell
- Contents
- 1 Getting to know L/L-S balances line
- 2 Startup
- 3 Weighing
- 4 Menu
- 4.1 Overview
- 4.2 Menu operation
- 4.3 Description of menu options
- 4.3.1 Reset or recording of balance settings (1st menu option “RESET”)
- 4.3.2 Functions (2nd menu option / see Section 5 for their use)
- 4.3.3 Weighing mode (3rd menu option)
- 4.3.4 Weighing unit 1 (4th menu option “UNIT 1”)
- 4.3.5 Weighing unit 2 (5th menu option “UNIT 2”)
- 4.3.6 Autozero (6th menu option / see overview and notes in Section 4.1)
- 4.3.7 Auto shut off
- 4.3.8 Peripheral unit (8th menu option / see overview and notes in Section 4.1)
- 4.3.9 Send mode (9th menu option / see overview and notes in Section 4.1)
- 4.3.10 Send format (10th menu option / see overview and notes in Section 4.1)
- 4.3.11 Baud rate (11th menu option / see overview and notes in Section 4.1)
- 4.3.12 Bit/Parity (12th menu option / see overview and notes in Section 4.1)
- 4.3.13 Handshake (13th menu option / see overview and notes in Section 4.1)
- 5 Functions
- 6 Technical data, options, optional equipment
- 7 Appendix
Menu
12
4.2 Menu operation
0.01 g
Ÿ≈ENU
rESEt
Menu
rESEt
±±
±±
±
““
““
“
StorEd
0.01 g
Menu
0.01 g
C
Opening the menu
In weighing mode, press and hold down the «Menu» key until “MENU” appears in the
display. Release the key: the 1st menu option is displayed.
Select menu options
The «
±±
±±
±» key is used to select individual menu options with their current settings one
after the other.
Change settings
Pressing the «
““
““
“» key displays the next setting; pressing the «1/10d» key displays
the previous one. Once the desired setting appears in the display, the next menu
option can be selected («
±±
±±
±») or you can close the menu (see following Section).
Saving settings and closing the menu
Hold the «Menu» key down until “StorEd” appears in the display. Release the key and
the balance reverts to weighing mode. All changes are saved.
Abort
Press the «C» key briefly. The balance reverts to weighing mode. Changes are not
saved.
Note
If no entry is made within 45 seconds, the balance reverts to weighing mode.
Changes are not saved.
▼
4.3 Description of menu options
4.3.1 Reset or recording of balance settings (1st menu option “RESET”)
Reset balance settings
➞ Select “Reset”, press and hold down the «Menu» key until the message “r donE”
confirms that all menu settings have been reset. The balance then reverts to
weighing mode and works with the factory settings (Section 4.1).
Recording balance settings
➞ Select “List” and hold down the «Menu» key until the message “StorEd” is
displayed.
The current balance settings are transmitted to the peripheral device connected to
the optional RS232C interface. To do this the setting “Printer” must always be
selected at the 8th menu option (Peripheral unit). The current balance settings
are saved at the same time.
rESEt
r donE
0.00 g
Menu
rESEt
LISt
““
““
“
StorEd
0.00 g
Menu
F count
PCS
F 100
F count
PCS
%