Operating instructions

ManualsBrandsMettler Toledo ManualsComputer equipmentGA42

METTLER TOLEDO

B-S line of balances

• AB-S

• PB-S

(Version as from October 2003)

METTLER TOLEDO

O/T

Cal/Menu

off

O/T

Cal/

enu

off

O/T

Summary of content (40 pages)

PAGE 1
Operating instructions METTLER TOLEDO B-S line of balances • AB-S • PB-S On off O/ T MET C TLE R TOL EDO F Cal (Version as from October 2003) /Men u On off O/ T MET C TLE R TOL EDO F Cal /M enu On off O/ T MET C F Cal /Men u TLE R TOL EDO
PAGE 2
Operating instructions in a nutshell Press key briefly Adjusting (calibration) external Piece counting* Dynamic weighing* Note: Various models (AB-S, certified balances) have an internal adjustment weight Automatic start (Dyn A) 0.00 g On off Press and hold key down until the desired display appears ▼ O/T METT LER TOLE C Cal/Menu DO F Cal/M enu CAL # ▼ 2000.00 automatic sequence Cal “ 0.00 g On off On O/T off METT -----off O/T METT LER TOLE C METT DO F Cal/M enu 0.
PAGE 3
Contents 1 Getting to know B-S balances ...................................................... 4 5 Functions ................................................................................... 23 1.1 1.2 1.3 Introducing the B-S line of balances ............................................... 4 Layout of B-S balances ................................................................ 5 Overview of key functions ............................................................. 6 5.1 5.2 5.3 5.
PAGE 4
1 Getting to know B-S balances 1.1 Introducing the B-S line of balances Several types of construction – uniform operation AB-S (0.1 mg / 0.01 mg) • The B-S balance line ranges from high-resolution analytical balances (AB-S) with a readability of 0.1 mg / 0.01 mg through to precision balances (PB-S) with a readability of 0.001 g to 1 g. The weighing ranges extend from 51 g to 8.1 kg. • The operation of all theses balances is identical.
PAGE 5
1.
PAGE 6
1.3 Overview of key functions The balances have two operator control levels: the weighing mode and the menu. The function of each individual key depends on the operator control level and how long the key is pressed. Weighing mode Key functions in weighing mode 0.
PAGE 7
2 2.1 Startup Unpacking / standard equipment All B-S balances are supplied in environmentally compatible packaging.
PAGE 8
2.3 Setting up, leveling, preparations for weighing below the balance, connecting to power supply The optimum location The correct location makes an important contribution to the accuracy of the weighing results of high-resolution analytical and precision balances.
PAGE 9
Leveling B-S balances have a spirit level and two adjustable leveling feet to compensate for slight irregularities in the surface of the weighing bench. The balance is exactly horizontal when the air bubble is in the middle of the level glass.
PAGE 10
Adjusting (calibration) To obtain accurate weighing results, the balance must be adjusted to match the gravitational acceleration at its location. Adjusting is necessary • before the balance is used for the first time • at regular intervals during weighing service • after a change of location Procedure To obtain accurate results, the balance must be connected to the power supply for 30 minutes (AB-S analytical balances 60 minutes) in order to reach operating temperature before adjusting.
PAGE 11
Precision balances (PB-S) Cal/Menu CAL à 2000.00 Cal à On off O/ T METTL ER TOLE C DO F Cal ------ Cal ➞ Have required adjustment weight ready (for certified models please refer to the notes below). ➞ Unload weighing pan ➞ Press and hold the «Cal/Menu» key down until “CAL” appears in the display, then release key. The required adjustment weight value flashes in the display. ➞ Place adjustment weight in center of pan. The balance adjusts itself automatically. ➞ When “0.
PAGE 12
3 Weighing 3.1 On/off switching Switching on ➞ Remove any load from weighing pan and press «On» key briefly. On 88888888 The balance performs a display test (all segments in the display light up briefly). When zero is displayed, the balance is ready for operation. à 0.00 g Switching off Off OFF ➞ Press and hold the «Off» key down until “OFF” appears in the display. Release the key. à 3.2 Simple weighing ➞ Place weighing sample on the weighing pan. 0.
PAGE 13
3.3 Taring ➞ Place empty container on the balance. 0.00 g 121.01 g On off O/ T METTL ER TOLE C ➞ The weight is displayed. DO F Cal /Me nu # 0.00 g 95.97 g ➞ Tare: press the «#» key briefly. ➞ Add weighing sample to container. The net weight is now displayed. On off O/ T METTL ER TOLED C O F Cal /Me nu If the container is removed from the balance, the tare weight will be shown as a negative value. -121.
PAGE 14
3.4 METTLER TOLEDO DeltaRange balances # 812.7 g 0.00 g METTLER TOLEDO DeltaRange balances have a movable fine range with 10 times smaller display increments over their entire weighing range. In this fine range an additional decimal place always appears in the display. The balance operates in the fine range • after switching on • after every taring operation If the fine range is exceeded, the balance display automatically switches to coarser display increments.
PAGE 15
4 4.1 Menu Overview In the menu you can change the weighing unit (for certified balances, only if the national certification law allows), select additional functions and carry out various settings. A description of the individual menu options is given in Section 4.3. Notes 1) 2) 3) 4) This menu option is only available on AB-S models.
PAGE 16
Menu operation Opening the menu Cal/Menu 0.01 g In weighing mode, press and hold down the «Cal/Menu» key until “MENU” appears in the display. Release the key: the 1st menu option is displayed. Ÿ≈EMU à 4.2 rESEt Select menu options ± rESEt The «±» key is used to select individual menu options with their current settings one after the other. Unit 1 g Change settings “ Unit 1 g Unit 1 kg The «“» key is used to change the setting at the selected menu option.
PAGE 17
4.3 Description of menu options 4.3.1 Reset or recording of balance settings (1st menu option “RESET”) Reset balance settings Cal/Menu ➞ Select “Reset”, press and hold down the «Cal/Menu» key until the message “r donE” confirms that all menu settings have been reset. The balance then reverts to weighing mode and works with the factory settings (Section 4.1). rESEt r donE 0.00 g “ Recording balance settings ➞ Select “List” and hold down the «Cal/Menu» key until the message “StorEd” is displayed.
PAGE 18
F count “ “ PCS F 100 % F dyn A “ F dyn Ÿ≈ “ F nonE “ Std “ 4.3.3 Functions (3rd menu option / Operating Section 5) In addition to simple weighing, the following functions can be selected: F count Piece counting F 100 % Percent weighing F dYn A Dynamic weighing with automatic start F dYn M Dynamic weighing with manual start F nonE No function, simple weighing (factory setting) doS 4.3.
PAGE 19
UniuErS “ unStAbLE StAbLE “ FASt -rEL rELiAbLE FASt “ Unit 1 g “ Unit 1 m … “ … Unit 1 mg Unit 1 t tl 4.3.5 Vibration adapter (5th menu option) (Only on AB135-S/AB265-S models) The vibration adapter can be used to match your balance to the ambient conditions (vibrations, drafts at location). If you work in surroundings which are practically free from temperature fluctuations, drafts, and vibrations, select “StabLE”.
PAGE 20
4.3.8 Weighing unit 2 (8th menu option “UNIT 2”) If it is required to show the weighing results in weighing mode in an additional unit by pressing the «“» key, the desired second weighing unit can be selected in this menu option. The same weighing units are available as under “UNIT 1”, with the exception of the tael units (“H tl”, “S tl” und “t tl”). 4.3.9 Autozero (9th menu option) This menu option allows you to switch the automatic zero correction on or off.
PAGE 21
S. oFF “ S. Stb 4.3.11 Send mode (11th menu option) Note: This menu option is only available if you have selected the setting “Host” in the 10th menu option (Peripheral unit)! At this menu option you specify how data is transmitted to a peripheral device. S. oFF Send mode switched off S. Stb The next possible stable value will be transferred after the «±» key has been triggered. S. Cont S. Cont All values are transferred automatically. S. SICS 4.3.
PAGE 22
“ 7b-E 7b-no “ 8b-no “ 4.3.14 Bit/Parity (14th menu option) Note: This menu option is only available if you have selected the setting “Host” in the 10th menu option (Peripheral unit)! At this menu option you can set the character format for the attached peripheral device. 7b–E 7 data bits/even parity 7b–no 7 data bits/no parity 8b–no 8 data bits/no parity 7b–odd 7 data bits/odd parity 7b-odd “ HS oFF 4.3.
PAGE 23
5 Functions 5.1 Piece counting Requirement The function “F count” must be activated in the menu (Section 4). # 0.00 g ➞ Place empty container on the balance and tare by briefly pressing the «#» key. Setting the reference: a reference weight must first be entered for piece counting: On off O/T MET TLER TOL C EDO F Cal/M enu On off O/T MET TLER TOL C EDO F F Cal/M enu SEt 10 PCS ➞ Add a number of reference pieces to container.
PAGE 24
5.2 Percent weighing Requirement 0.00 g The function “F 100 %” must be activated in the menu (Section 4). Set target weight 148.50 g ➞ Target weight (Reference weight, which corresponds to 100 %) in center of pan. On off O/T MET TLER TOL C EDO F Cal/M enu F SEt100 % ➞ Hold the «F» key down until “SEt 100 %” is displayed. ➞ Press the «“» key to select “SEt 100 %” or “SEt no %” (Percent weighing deactivated). 100.
PAGE 25
5.3 Dynamic weighing Dynamic weighing is suitable for the weighing of unstable weighing samples. The mean value of the weighing results is determined over a specified time period (weighing time). The more unstable the weighing sample, the longer the selected weighing time. Requirement “F dYn A” for automatic start or “F dYn M” for manual start must be activated in the menu (Section 4). Factory setting is a weighing time of 3 seconds (t = 3"). Tare container ➞ Tare: Press the «#» key.
PAGE 26
0.00 g “ < 0.00 g < • 257.35 g Dynamic weighing with manual start (F dYn M) ➞ The «“» key can be used select the dynamic weighing. The display shows the symbol ,. ➞ Load weighing sample. On off O/T MET TLER TOL C EDO F Cal/M ± enu < -- 3 -- ➞ Start weighing with the «±» key. During the weighing time, a “count down” runs in the display. < -- 1 -- ▼ < ‹ 260.33 g ➞ Read off result.
PAGE 27
5.4 Switching weight units Requirement Different weight units must be activated in the menu for unit 1 and unit 2 (Section 4). “ 64.71 g ➞ The «“» key can be used at any time to toggle between the two weighing units selected in the menu (“UNIT 1” and “UNIT 2”). 64710 mg Notes: • Switching between weight units may be blocked with certified balances, depending on national weights and measures legislation. • This function is not available with dynamic weighing.
PAGE 28
6 6.1 Technical data, optional equipment Technical data Standard equipment of B-S balances Materials • Housing: die-cast aluminum, painted • Weighing pan: 18/10 chromium-nickel steel • Protective cover, transparent, made from Barex • AC adapter to national codes according list on page 33. Balance power input: 8-14.5V, 50/60Hz, 6VA or 9.
PAGE 29
PB153-S PB303-S PB303-S DeltaRange PB403-S PB602-S PB1502-S PB3002-S Readability 0.001 g 0.001 g 0.001 g*/0.01 g 0.001 g 0.01 g 0.01 g 0.01 g Max. capacity 151 g 310 g 60 g*/310 g 410 g 610 g 1510 g 3100 g Repeatability (s) 0.001 g 0.001 g 0.001 g*/0.005 g 0.001 g 0.01 g 0.01 g 0.01 g Linearity –/+ 0.002 g 0.002 g 0.002 g*/0.01 g 0.002 g 0.02 g 0.02 g 0.
PAGE 30
PB3002-S DeltaRange PB4002-S PB1501-S PB3001-S PB5001-S PB8001-S PB8000-S Technical data Readability 0.01 g*/0.1 g 0.01 g 0.1 g 0.1 g 0.1 g 0.1 g 1 g Max. capacity 600 g*/3100 g 4100 g 1510 g 3100 g 5100 g 8100 g 8100 g Repeatability (s) 0.01 g*/0.05 g 0.01 g 0.05 g 0.05 g 0.05 g 0.05 g 0.5 g Linearity –/+ 0.02 g*/0.1 g 0.02 g 0.1 g 0.1 g 0.1 g 0.1 g 0.
PAGE 31
6.3 MT-SICS Interface commands and functions Many of the balances and scales used have to be capable of integration in a complex computer or data acquisition system. To enable you to integrate balances in your system in a simple manner and utilize their capabilities to the full, most balance functions are also available as appropriate commands via the data interface.
PAGE 32
Die unten aufgeführten MT-SICS Befehle sind eine Auswahl der zur Verfügung stehenden Befehle. Weitere Befehle und Informationen entnehmen Sie bitte dem Bedienungshandbuch “MT-SICS Basic-S balances 11780447”, das Sie unter www.mt.com/AB-S aus dem Internet herunterladen können. ST – Send stable weight after pressing ± (transfer) key Command ST Inquiry of actual status of the ST function.
PAGE 33
6.4 Optional equipment AC adapters Antitheft device For all models except AB135-S/AB265-S • Cable with lock (for all models) Output: 12V ~ 500mA • Euro 230V/50Hz/80mA 11103740 • Euro/(grd) 230V/50Hz/80mA 11103744 • UK 240V/50Hz/80mA 11103742 • USA 120V/60Hz/10W 11103741 • Japan 100V/50Hz/10W 11103743 Output: 12V ~ 1.0A • Universal (bench version) 11103745* 220-240V/50Hz/100mA For AB135-S/AB265-S (as well as for all B-S models) Output: 12V … 2.08A • Universal (bench version) 100-240V, 50-60Hz, 0.
PAGE 34
6.5 Dimensional drawings All dimensions in millimeters (mm) PB-S balance with no draft shield PB-S balance with “mg” draft shield (low) AB-S balance with “0.1 mg” draft shield (high) 128.5 91.5 168.5 181 89 92.5 92.5 Ø 236 154.5 344 252 91.5 266 10.5 10.5 266 321 266 321 321 184.5 183.5 184.5 163.5 Ø 100 73.5 10 10 1) 1) 10 Ø 84 1) Opening for hanger 245 190 38 141 213 245 190 181 213 245 190 213 1) 193 10.
PAGE 35
7 7.1 Appendix Typical printouts from METTLER TOLEDO GA42 and LC-P45 printers Function: Adjusting - BALANCE CALIBRATION Date: ................. Time: ................. Function: Dynamic weighing --- DYNAMIC WEIGHING --Weigh Time: 2 s DW METTLER TOLEDO Type: PB3002-S SNR: 1118015657 SW: 1.20 Weight ID: ............. Weight: 2000.00 g External Cal. done Signature: 49.999 g Function: List Printout of the current balance settings --- LIST OF SETTINGS --Date: ................. Time: .................
PAGE 36
7.2 What if ...? Error/Error message íååååì î____ï Error 1 Error 2 Error 3 Error 4 Error 6 0.000 Abort Cause Rectification Overload ➞ Remove sample from weighing pan, zero again (tare). Underload ➞ Check whether weighing pan is positioned properly. No stability ➞ Wait for stability before pressing key. • in taring or adjusting (calibration) • when reference weight for piece counting is placed on pan ➞ Ensure more stable ambient conditions.
PAGE 37
7.3 Connecting B-S balances to other METTLER TOLEDO devices Device Connecting cable Titrators: DL67, 70ES, 70 V.
PAGE 38
PAGE 39
Leer
PAGE 40
To protect your METTLER TOLEDO product’s future: METTLER TOLEDO Service assures the quality, measuring accuracy and preservation of value of all METTLER TOLEDO products for years to come. Please send for full details about our attractive terms of service. Thank you. P11780440 Subject to technical changes and to the availability of the accessories supplied with the instruments. Printed on recycled paper. Because we care. © Mettler-Toledo GmbH 2003 11780440C Printed in Switzerland 0310/2.