User Manual

3.2 Remote control commands3.2 Remote control commands
768 KF Oven
22
│& Root
│ Setup Setting the operating mode
│ │ .IdReport Output report identification ON, OFF 3.2.2.31
│ │ .Keycode Key code of pressed keys ON, OFF 3.2.2.32
│ │ .Tree Definition of response to $Q
│ │ │ .Short Send short path name ON, OFF 3.2.2.33
│ │ │ .ChangedOnly Only paths with changed values ON, OFF 3.2.2.33
│ │ .Trace Message when values change ON, OFF 3.2.2.34
│ │
│ │ .Lock Lock functions
│ │ │ .Keyboard Lock all keys ON, OFF 3.2.2.35
│ │ │ .Config Lock <CONFIG> key ON, OFF 3.2.2.35
│ │ │ .Parameter Lock <PARAM> key ON, OFF 3.2.2.35
│ │ │ .Heater Lock <HEATER> key ON, OFF 3.2.2.35
│ │ │ .Pump Lock <PUMP> key ON, OFF 3.2.2.35
│ │ │ .Valve Lock <VALVE> key ON, OFF 3.2.2.35
│ │ │ .Boat Lock <BOAT IN/OUT> keys ON, OFF 3.2.2.35
│ │ │ .Display Lock display operation of 768 ON, OFF 3.2.2.35
│ │
│ │ .TController Factors for temperature controller
│ │ │ .InitHeatFactor Inital heating factor 0...200 3.2.2.36
│ │ │ .AddHeatFactor Heating after initial phase 0...200 3.2.2.36
│ │
│ │ .SendMeas Automatic transmission of measurement data
│ │ │ .SendStatus On/off switching of transmission ON, OFF 3.2.2.37
│ │ │ .Interval Time interval for transmission 1...16200 3.2.2.37
│ │ │ .Meas Measured values for transmission
│ │ │ │ .CyclNo Cycle number ON, OFF 3.2.2.37
│ │ │ │ .SampleTemp Sample temperature ON, OFF 3.2.2.37
│ │ │ │ .OvenTemp Oven temperature ON, OFF 3.2.2.37
│ │ │ │ .GasFlow Gas flow ON, OFF 3.2.2.37
│ │
│ │ .AutoInfo Automatic message on changes
│ │ │ .Status On/off of all set messages ON, OFF 3.2.2.38
│ │ │ .P When power is switched on ON, OFF 3.2.2.38
│ │ │ .T Messages of automatic determination
│ │ │ │ .G Status becomes "Go" ON, OFF 3.2.2.38
│ │ │ │ .R Status becomes "Ready" ON, OFF 3.2.2.38
│ │ │ │ .S Status becomes "Stop" ON, OFF 3.2.2.38
│ │ │ │ .B Beginning of sample heating ON, OFF 3.2.2.38
│ │ │ │ .F Finish of sample heating ON, OFF 3.2.2.38
│ │ │ │ .E Error message ON, OFF 3.2.2.38
│ │ │ .I Change of an I/O input ON, OFF 3.2.2.38
│ │ │ .O Change of an I/O output ON, OFF 3.2.2.38
│ │
│ │ .PowerOn Simulation "Power on" $G 3.2.2.39
│ │ .Initialise Set values to default $G 3.2.2.40
│ │ │ .Select Selection Mode,Config,All
│ │ │ Setup,Assembly 3.2.2.40
│ │ .RamInit Initialisation $G 3.2.2.41
│ │ .InstrNo Set instrument identification $G 3.2.2.42
│ │ │ .Value Enter instrument identification 8 ASCII 3.2.2.42
│ │ .Save Store in EEPROM $G 3.2.2.43