Manual

3.2 Remote control commands3.2 Remote control commands
768 KF Oven
22
³& Root
³ Setup Setting the operating mode
³ ³ .IdReport Output report identification ON, OFF 3.2.2.31
³ ³ .Keycode Key code of pressed keys ON, OFF 3.2.2.32
³ ³ .Tree Definition of response to $Q
³ ³ ³ .Short Send short path name ON, OFF 3.2.2.33
³ ³ ³ .ChangedOnly Only paths with changed values ON, OFF 3.2.2.33
³ ³ .Trace Message when values change ON, OFF 3.2.2.34
³ ³
³ ³ .Lock Lock functions
³ ³ ³ .Keyboard Lock all keys ON, OFF 3.2.2.35
³ ³ ³ .Config Lock <CONFIG> key ON, OFF 3.2.2.35
³ ³ ³ .Parameter Lock <PARAM> key ON, OFF 3.2.2.35
³ ³ ³ .Heater Lock <HEATER> key ON, OFF 3.2.2.35
³ ³ ³ .Pump Lock <PUMP> key ON, OFF 3.2.2.35
³ ³ ³ .Valve Lock <VALVE> key ON, OFF 3.2.2.35
³ ³ ³ .Boat Lock <BOAT IN/OUT> keys ON, OFF 3.2.2.35
³ ³ ³ .Display Lock display operation of 768 ON, OFF 3.2.2.35
³ ³
³ ³ .TController Factors for temperature controller
³ ³ ³ .InitHeatFactor Inital heating factor 0...200 3.2.2.36
³ ³ ³ .AddHeatFactor Heating after initial phase 0...200 3.2.2.36
³ ³
³ ³ .SendMeas Automatic transmission of measurement data
³ ³ ³ .SendStatus On/off switching of transmission ON, OFF 3.2.2.37
³ ³ ³ .Interval Time interval for transmission 1...16200 3.2.2.37
³ ³ ³ .Meas Measured values for transmission
³ ³ ³ ³ .CyclNo Cycle number ON, OFF 3.2.2.37
³ ³ ³ ³ .SampleTemp Sample temperature ON, OFF 3.2.2.37
³ ³ ³ ³ .OvenTemp Oven temperature ON, OFF 3.2.2.37
³ ³ ³ ³ .GasFlow Gas flow ON, OFF 3.2.2.37
³ ³
³ ³ .AutoInfo Automatic message on changes
³ ³ ³ .Status On/off of all set messages ON, OFF 3.2.2.38
³ ³ ³ .P When power is switched on ON, OFF 3.2.2.38
³ ³ ³ .T Messages of automatic determination
³ ³ ³ ³ .G Status becomes "Go" ON, OFF 3.2.2.38
³ ³ ³ ³ .R Status becomes "Ready" ON, OFF 3.2.2.38
³ ³ ³ ³ .S Status becomes "Stop" ON, OFF 3.2.2.38
³ ³ ³ ³ .B Beginning of sample heating ON, OFF 3.2.2.38
³ ³ ³ ³ .F Finish of sample heating ON, OFF 3.2.2.38
³ ³ ³ ³ .E Error message ON, OFF 3.2.2.38
³ ³ ³ .I Change of an I/O input ON, OFF 3.2.2.38
³ ³ ³ .O Change of an I/O output ON, OFF 3.2.2.38
³ ³
³ ³ .PowerOn Simulation "Power on" $G 3.2.2.39
³ ³ .Initialise Set values to default $G 3.2.2.40
³ ³ ³ .Select Selection Mode,Config,All
³ ³ ³ Setup,Assembly 3.2.2.40
³ ³ .RamInit Initialisation $G 3.2.2.41
³ ³ .InstrNo Set instrument identification $G 3.2.2.42
³ ³ ³ .Value Enter instrument identification 8 ASCII 3.2.2.42
³ ³ .Save Store in EEPROM $G 3.2.2.43