User guide

6 Interfaces
732 IC Detector / 733 IC Separation Center
174
Object Meaning Entry range/Selection
³ Ã.Mark Trigger marking signal (=<MARK> key) 1…7…15
³ Ã.Zerooff Switch off auto-zero (=<ZERO OFF> key) 1…9…15
³ Ã.Plot Trigger graphics plot (=<PLOT> key) 1…10…15
³ Ã.Polarity Switch polarity at analog output 1…11…15
³ Ã.Select Select (=<SELECT> key) 1…13…15
³ Ã.Quit Quit (=<QUIT> key) 1…14…15
³ À.Enter Enter (=<ENTER> key) 1…15…15
Ã.Graphics General graphics parameters
³ Ã.Grid Grid lines on graphics output on, off
³ Ã.Frame Frame on graphics output on, off
³ À.Recorder Setting of printout
³ À.Width Relative width of printout 0.4…0.8…1.0
À.Peripherals Peripheral instruments
Ã.With733 Operation with 733 IC Separation Center on, off
À.With709 Operation with 709 IC Pump on, off
&Assembly Basic elements of the assembly
³
Ã.Meas Measurement
³ À.State On/off switching of measurement on, off
³
À.Outputs Remote lines
Ã.SmplX
³
Activate (on) or deactivate (off) remote output lines
on, off
Ã.AutoEOD
³
Automatic output of EOD on program end and
"return" with loop programs
on, off
Ã.SetLines
³ ³
³ ³
³ ³
³ ³
³ ³
³ ³
Set remote outputs 1…16:
Interface "709 IC Pump": outputs 1…8
Interface "Remote": outputs 9…16
active setting of a static signal
inactive resetting of the static signal
pulse output a pulse (length ca. 150 ms)
off do not set line
$G
³ Ã.L1 Signal of output line 1 (pin 5) active, inactive, pulse, off
³ Ã.L2 Signal of output line 2 (pin18) active, inactive, pulse, off
³ Ã.L3 Signal of output line 3 (pin 4) active, inactive, pulse, off
³ Ã.L4 Signal of output line 4 (pin17) active, inactive, pulse, off
³ Ã.L5 Signal of output line 5 (pin 3) active, inactive, pulse, off
³ Ã.L6 Signal of output line 6 (pin16) active, inactive, pulse, off
³ Ã.L7 Signal of output line 7 (pin 1) active, inactive, pulse, off
³ Ã.L8 Signal of output line 8 (pin 2) active, inactive, pulse, off
³ Ã.L9 Signal of output line 9 (pin 5) active, inactive, pulse, off
³ Ã.L10 Signal of output line 10 (pin18) active, inactive, pulse, off
³ Ã.L11 Signal of output line 11 (pin 4) active, inactive, pulse, off
³ Ã.L12 Signal of output line 12 (pin17) active, inactive, pulse, off
³ Ã.L13 Signal of output line 13 (pin 3) active, inactive, pulse, off
³ Ã.L14 Signal of output line 14 (pin16) active, inactive, pulse, off
³ Ã.L15 Signal of output line 15 (pin 1) active, inactive, pulse, off
³ À.L16 Signal of output line 16 (pin 2) active, inactive, pulse, off
À.ResetLines Set remote outputs 1…16 to ”off” $G