Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installationDash Kit

A~~

DP-7528

IYILIA

INSTALLATION

INSTRUCT

ONS

KIT

COMPONENTS

Mazda

Miata

1990-1993

Visit

MetraOnllnuom

for

detailed

informat

about

the

product

and

up-to-date

vehicle

specific

applications

KIT

FEATURES

•

ISO

DIN

radio

provision

with

pocket

•

ISO

ODIN

radio

provision

•

Textured

match

the

factory

dash.

•

Can

also

used

factory

dash

replacement

with

factory

Mazda

radios.

•

Radio

housing

•

Radio

trim

panel

•

Radio

brackets

•

Pocket

•

3/8"

Phillips

screws

(10)

•

Panel

clips

(2)

•

1/2"

Phillips

screws

(2)

TABLE

CONTENTS

Dash

Disassembly

.....

..........

....

...

....

...

....

2-3

Kit

Preparation

...

......

........

........................

...

Kit

Assembly

-ISO

DIN

radio

provision

with

pocket...

...

....

...

. 5

-ISO

DDIN

radio

provision

........

....

........

.........

WIRING

ANTENNA

CONNECTIONS

(sold

separately)

Wiring

Harness:

70-7901

Visit

metraonline.com

for

audio/video

and

steering

wheel

control

interface

options

Antenna

Adapter:

Not

required

II II

TOOLS

REQUIRED

Netra.

TIie

WOlld's

Best

lits.

•

Metra0n11ne.com

2021

NEYRA

ElECTRONICS

CORPORATION

•

Panel

removal

tool

•

Phillips

screwdriver

Attention!

With

the

key

out

the

ignition

disconnect

the

negative

battery

terminal

before

Installing

this

product

Ensure

that

all

Installation

connections

are

secure

before

cycling

the

ignition

test

this

product.

REV.

8/26/21

INSTOP·7S28

c.o

----------------------------------------------

....,.

Summary of content (7 pages)

PAGE 1
A~~ DP-7528 IYILIA INSTALLATION INSTRUCTIONS I Mazda Miata 1990-1993 Visit MetraOnllnuom for more detailed information about the product and up-to-date vehicle specific applications KIT FEATURES • ISO DIN radio provision with pocket • ISO ODIN radio provision • Textured to match the factory dash. • Can also be used as afactory dash replacement with factory Mazda radios.
PAGE 2
DASH DISASSEMBLY From the center console: 4. Unscrew gear shift knob. (Figure D) 1. Unclip ashtray to reveal (1) Phillips screw and remove. (Figure A) 5. Unplug (2) connectors and remove the center console. (Figure E) 2. Open storage compartment and remove (2) Phillips screws. (Figure B) 3. Locate the (2) Phillips screws on the front sides of the gear shifter trim panel and remove. (Figure () Continued on the next page (Figure A) (Figure D) (Figure B) (Figure E) (Figure C) B Me7ra> 386.257.
PAGE 3
DASH DISASSEMBLY 4. Remove (2) Phillips screws from the From the factory radio assembly: support bar on top of radiotrim. Save bar for kit preparation. (FigureI) 1. Unclip and remove center air vents to reveal (2) screws at the top of the radio trim panel. Remove the (2) screws. (Figure F) 2. Unplug and remove the radio trim panel. (Figure G) 3. Remove the (4) Phillips screws and pull (CONT.) 5. Remove (2) Phillips screws to remove the hazard switch. Save switch for kit preparation.
PAGE 4
KIT PREPARATION 1. Secure the support bar to the top of the radio housing using the (2) screws removed in step 4. (Figure A) 2. Secure the hazard switch using the (2) #8 x1/2" Phillips screws provided. (Figure B) 3. Transfer the retaining clips to the corresponding locations on the radio housing using screws removed in step 6. (Figure C) 4. Attach the radio trlmplate to the radio housing using (6) of the supplied #8 x3/8" Philips screws. (Figure D) 5. Attach the (2) panel clips to the radio housing.
PAGE 5
KIT ASSEMBLY ISO DIN radio provision with pocket 1. Attach the pocket to the radio brackets using (4) of the supplied #8 x3/8" Phillips screws. (Figure A) 2. Slide the radio into the bracket/pocket assembly and secure it using the screws supplied with the radio. (Figure B) ~(iii. (iii. ~- 3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. ~ ~' a,~· ··...
PAGE 6
KIT ASSEMBLY ISO ODIN radio provision 1. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A) 2. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. 3. Slide the radio into the sub dash and secure it using the factory hardware. 4. Reassemble the dash in reverse order of disassembly using the new 7528 radio housing.
PAGE 7
~~ 1da 'a DP-7528 INSTALLATION INSTRUCTIONS Having difficulties? We're here to help. Contact our Tech Support line at: 386-257-1187 Or viaemail at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM siu~arlQOOAM-lOOPM Sunday: 10:00 AM - 4:00 PM A 1. -c. ♦ ~ KNOWLEDGE IS POWER 'II • Enhance your lnataltallon and fabrication akllls by enrolling In the moat ...:ognl- and reopected mobile electronlca IIChocl In our lnduotry. Log onto www.