Owner's Manual
2.
Installation of
IR
control
components
Install the connecting block
in
an
accessible
location behind or
next to the controlled products
and
near
an
11
OV
plug.
Take
into
account the
IR
emitters
cable's
length
and
make
sure
that
all
cables
are
serviceable
and
kept
accessible
.
Mount the
IR
emitters onto the
IR
receiving port
on
each
of the
controlled
items.
Route
the emitter
cables
to the
IR
connecting block. A
self-adhesive
backing
is
supplied for
each
emitter.
NOTE:
Test
the
IR
emitter at the desired location prior the
removing
adhesive
backing.
Plug
the male emitter terminal into
the emitter ports
on
the connecting block. Mount the
IR
receiver
at
a location that
can
easily
be
seen
by
your
hand
held remote.
NOTE:
Avoid
the
IR
receiver
being
placed
where it
is
exposed
to
direct sunlight or fluorescent light
as
these will overload
its
receiving capability. Experiment with the
best
location prior the
removing
adhesive
backing
.
Connect the power
supply.
You
are
now done with the
IR
section
of
your installation.
3.
Overview
of
the
Remote
learning
and
Relay
control
functions
The
CS-IRKITCCUS
is
very
unique
in
that it
has
the ability to
learn
two
IR
codes
from most
remotes
to provide a
Dry
Contact
Closure
interface to
relay
controlled
devices
.
The
unit
also
comes
equipped with five
LED
indicators to show learning
plus
operating
status
and
two buttons to enable the
IR
code
learning
process.
1 -
LED
Power
Indicator
2 - B Contact
Closed
(A
Open)
Indicator
3 - A Contact
Closed
(B
Open)
Indicator
4
-A
Closed
Learning
Indicator
5 - B
Closed
Learning
Indicator
6 - A Contact
Close
Learn
7 - B Contact
Close
Learn
0
0
The
CS-IRKITCCUS
is
equipped with a 4
Port
Phoenix
style
connecting terminal to allow the wiring of your
relay
controlled
devices
.
NA
-
No
purpose
(do
not
use)
A
Close
-
You
will
use
this port for
one
conductor most
NC
(normally
closed)
products. -
When
A
is
closed
Bis open.
B
Close
-
You
will
use
this port for
one
conductor most
NO
(normally open) products.
When
Bis
closed
A
is
open
Common -
This
port
is
used
for the
second
conductor for
any
NC
or
NO
device
.
NOTE:
THIS
IS
A
CONTACT
CLOSURE
DEVICE;
DO
NOT
CONNECT
POWER
TO
THE
PHOENIX
PLUG.
4.
Wiring
and
Programming
for
one
Relay
(Dry
Contact
Closure)
controlled
devices.
This
CS-IRKITCCUS
enables
you
to
copy
38
KHz
remote
codes
into the
product.
Connect the two
wires
from the
relay
controlled
device
into Port A for'A
CLOSE
- B
OPEN"
operation
of
the
CS-IRKITCCUS
and
the common port
on
the
Phoenix
connector.
Select
the remote
(and
its
mode)
that
you
will
be
learning the
codes
from.
Unplug the
IR
receiver
from the connecting block,
place
the
remotes
IR
in-line pointed at the
IR
receiver port
and
within 6
inches
of
the
IR
receiving port.
Press
and
hold the
"A
CLOSE
LEARN"
button
(6)
with
one
hand
and
then
press
and
hold the
Remote
button that
you
want to
learn
with the other
hand
for
at
least
2
seconds,
release
both buttons
at
the
same
time, the
code
should now
be
learned.
Follow the
same
directions using the
"B
CLOSE
LEARN"
button
(7)
to
perform the
"B
Close
Learn"
process
.