Instructions

ManualsBrandsMetra ManualsCar HarnessMetra Mercedes w/ MOST25 Amp, SWC Retention 2002-2010

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AXDIS-MB132

INSTALLATION INSTRUCTIONS

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made .......................................2

Installing the AXDIS-MB132 interface ...................3

Programming the AXSWC interface .....................4

Mercedes (with M.O.S.T. 25 ampliﬁer)

Data Interface with SWC 2002-2010

• Provides accessory power

• Designed for ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains balance

• Micro-B USB updatable

APPLICATIONS

MERCEDES

CLS Class (W219) 2004-2010

E Class (W211) 2002-2009 SLK Class (R171) 2004-2010

• AXDIS-MB132 interface

• AXDIS-MB132 ampliﬁer interface

• AXSWC interface

• AXDIS-MB132 harness

• AXSWC harness

• Female 3.5mm connector with stripped leads

Summary of content (8 pages)

PAGE 1
AXDIS-MB132 I N S TA L L AT I O N I N S T R U C T I O N S Mercedes (with M.O.S.T. 25 amplifier) Data Interface with SWC 2002-2010 INTERFACE FEATURES • Provides accessory power • Designed for amplified models • Provides NAV outputs (parking brake, reverse, speed sense) • Retains audio controls on the steering wheel • Retains balance • Micro-B USB updatable INTERFACE COMPONENTS • AXDIS-MB132 interface • AXDIS-MB132 amplifier interface • AXSWC interface • AXDIS-MB132 harness • AXSWC harness • Female 3.
PAGE 2
CONNECTIONS TO BE MADE From the aftermarket radio to the AXDIS-MB132 harness: • Connect the Black wire to the ground wire. • Connect the Yellow wire to the battery wire. • Connect the Red wire to the accessory wire. Note: There will be an accessory wire on the AXSWC harness to connect as well. • If the aftermarket radio has an illumination wire, connect the Orange wire to it. The following (3) wires are only for multimedia/navigation radios that require these wires.
PAGE 3
INSTALLING THE AXDIS-MB132 INTERFACE With the key in the off position: • Connect the AXDIS-MB132 harness to the AXDIS-MB132 interface. • Connect the AXDIS-MB132 harness to the AXDIS-MB132 amplifier interface. • Remove the dust cover from fiber optic port in the AXDIS-MB132 amplifier interface. • Connect the factory fiber optic cable into the AXDIS-MB132 amplifier interface. • Connect the AXDIS-MB132 harness to the wiring harness in the vehicle.
PAGE 4
PROGRAMMING THE AXSWC INTERFACE • Press and hold the Volume-Up button on the steering wheel. • Turn the ignition on, the L.E.D. in the AXSWC interface will start flashing rapidly, which means the AXSWC is looking for the vehicle and the radio. Note: If the L.E.D. did not start flashing rapidly, press the reset button for 3 seconds, while still holding the Volume-Up button. • After a few seconds the L.E.D. should stop flashing rapidly, and then go out for approximately 2 seconds.
PAGE 5
REV.
PAGE 6
PAGE 7
REV.
PAGE 8
AXDIS-MB132 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.