Specifications

ManualsBrandsMetra Manualschassis components99-7876

INSTALLATION INSTRUCTIONS FOR PART 99-7876

KIT FEATURES

• ISO Mount Radio Provision With Pocket

• A) Radio Housing • B) Radio Housing Brackets

Wiring & Antenna Connections (sold seperately)

• 70-1729 - Honda Harness 2008-up

• 40-HD10 - Honda Antenna Adapter 2006-up

KIT COMPONENTS

Small Flat Blade Screwdriver • Panel Removal Tool

• Phillips Screwdriver • Wire Cutters

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

HONDA

Pilot 2009-11

99-7876

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7876 APPLICATIONS HONDA Pilot 2009-11 99-7876 KIT FEATURES • ISO Mount Radio Provision With Pocket KIT COMPONENTS • A) Radio Housing • B) Radio Housing Brackets Wiring & Antenna Connections (sold seperately) • 70-1729 - Honda Harness 2008-up • 40-HD10 - Honda Antenna Adapter 2006-up A B TOOLS REQUIRED: Small Flat Blade Screwdriver • Panel Removal Tool • Phillips Screwdriver • Wire Cutters 1-800-221-0932 www.metraonline.
PAGE 2
99-7876 TABLE OF CONTENTS Dash Disassembly - HONDA Pilot 2009-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Kit Assembly - ISO Mount Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7876 DASH DISASSEMBLY HONDA PILOT 2009-11 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the left a/c vent panel surrounding the shifter. (Figure A) 3 Unclip and remove the right a/c vent panel. (Figure A) 4 Remove the (2) Phillips screws securing the pocket below the radio then unclip and remove the pocket. (Figure B) B 5 Remove (4) Phillips screws securing the radio, Unplug and remove the radio. (Figure C) Continued on page 2.
PAGE 4
99-7876 DASH DISASSEMBLY HONDA PILOT 2009-11 D 6 Remove the (6) screws retaining the (3) clip assemblies at the top edge of the factory radio/climate control assembly. Retain screws and clip assemblies for reuse. (Figure D) REAR VIEW 7 Remove (4) Phillips screws securing the factory climate control. Unplug and remove factory climate control. NOTE: Retain (4) Phillips screws and climate control for reuse in Kit Assembly. (Figure E) SIDE OF RADIO Continue to kit preparation.
PAGE 5
99-7876 KIT PREPARATION HONDA PILOT 2009-11 *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove support strut on radio housing. (Figure A) 2 Attach the (3) clips removed in step 6 of the disassembly to the 99-7876 radio housing using the factory hardware. (Figure B) Continue to kit assembly.
PAGE 6
99-7876 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the corresponding radio housing bracket to the radio housing (Figure A), then attach the climate control to the assembly using the (4) Phillips screws removed in step 7. (Figure B) 2 Position the aftermarket radio into the radio housing and secure using the hardware supplied with the radio. (Figure C) B Continue to final assembly.
PAGE 7
99-7876 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 8
99-7876 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.