User Manual

ManualsBrandsMetra ManualsAutomotiveMetra '07-up Honda Crv Radio Install Kit

INSTALLATION INSTRUCTIONS FOR PART 99-7873

99-7873

APPLICATIONS

Honda CR-V

2007-up

KIT FEATURES

• DIN Mount Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Mount Radio Provision

• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

C DE

TOOLS REQUIRED:

Small Flat Blade Screwdriver • Panel Removal Tool

Phillips Screwdriver

www.metraonline.com

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

• 70-1722 - Honda harness - 2006-up

• 40-HD10 - Honda antenna adapter - 2006-up

1-800-221-0932

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7873 APPLICATIONS Honda CR-V 2007-up 99-7873 KIT FEATURES • DIN Mount Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Mount Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket A B F C D E WIRING AND ANTENNA CONNECTIONS (Sold Separately) • 70-1722 - Honda harness - 2006-up • 40-HD10 - Honda ant
PAGE 2
99-7873 TABLE OF CONTENTS Dash Disassembly - Honda CR-V 2007-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7873 DASH DISASSEMBLY HONDA CR-V 2007-UP A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. SCAN 1 2 Unclip a/c control. Unplug and remove a/c control. (Figure A) MAX A/C RPT 2 SEEK/SK CATEGO IP RY 3 4 A/C HI LO 3 Unclip and remove panel above a/c vents. (Figure B) HI LO 4 Unclip the a/c vent panel including the hazard switch. Unplug and remove the panel. (Figure C) B 5 Remove (4) Phillips screws securing the radio. Unplug and remove radio.
PAGE 4
99-7873 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly.
PAGE 5
99-7873 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the Radio Housing until it snaps into place. (Figure B) 3 Snap the Trim Plate onto the front of the Radio Housing. (Figure B) 4 Snap the Pocket into the Radio Housing. (Figure C) B Continue to final assembly.
PAGE 6
99-7873 KIT ASSEMBLY DOUBLE DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the Radio Housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN radio into the DDIN bracket/Radio Housing assembly and secure the radio to the assembly using the screws supplied with the radio.
PAGE 7
99-7873 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the Radio Housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the stacked ISO mount units into the Double DIN Bracket/Radio Housing assembly and secure the units to the assembly using the screws supplied with the units.
PAGE 8
99-7873 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.