Specifications

ManualsBrandsMetra Manualschassis components99-7871

INSTALLATION INSTRUCTIONS FOR PART 99-7871

Small Flat Screwdriver • Phillips Screwdriver • Socket Wrench

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Head Unit Provision with Pocket

• ISO DIN Head Unit Provision with Pocket

• Double DIN Head Unit Provision

• ISO Stacked Head Unit Provision

• Stacked DIN Head Unit Provision

• Painted To Match Factory Dash:

99-7871= Gunmetal, 99-7871T= Taupe

A) Radio Housing • B) DDIN Trim Plate • C) ISO Trim Plate • D) Double DIN Brackets • E) Pocket

• F) (8) #8 Phillips Screws • G) ISO Brackets • H) (5) White Plastic Clips • I) (6) Metal Clips

KIT COMPONENTS

TOOLS REQUIRED:

APPLICATIONS

Honda Civic

2006-2010

99-7871/

99-7871T

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

• 70-1722 - Honda harness - 2006-up

• 40-HD10 - Honda antenna adapter 2005-up

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7871 APPLICATIONS Honda Civic 2006-2010 99-7871/ 99-7871T KIT FEATURES • DIN Head Unit Provision with Pocket • ISO DIN Head Unit Provision with Pocket • Double DIN Head Unit Provision • ISO Stacked Head Unit Provision • Stacked DIN Head Unit Provision • Painted To Match Factory Dash: 99-7871= Gunmetal, 99-7871T= Taupe KIT COMPONENTS A) Radio Housing • B) DDIN Trim Plate • C) ISO Trim Plate • D) Double DIN Brackets • E) Pocket • F) (8) #8 Phillips Screws • G) ISO Bra
PAGE 2
99-7871 TABLE OF CONTENTS Dash Disassembly Honda Civic 2006-2010....................................................................... 1,2 Kit Assembly: DIN Head Unit Provision.......................................................................... 3 ISO DIN Head Unit Provision ................................................................... 4 Double DIN Head Unit Provision ............................................................. 5 Stacked ISO DIN Head Unit Provision.............................
PAGE 3
99-7871 DASH DISASSEMBLY HONDA CIVIC 2006-2010 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the panel below the steering wheel. (Figure A) 3 Remove the (1) Phillips screw exposed on the lower left side of the panel above the steering wheel and around the instrument cluster. (Figure B) A B 4 Unclip and remove the panel around top of steering wheel and instrument cluster.
PAGE 4
99-7871 DASH DISASSEMBLY HONDA CIVIC 2006-2010 E 6 Unclip and remove radio/climate control assembly. (Figure E) 7 Remove (3) Phillips screws securing the a/c vent to the radio/climate control panel. (Figure F) 8 Remove the (4) Phillips screws securing the climate control to the radio/climate control panel. (Figure F) 9 Remove the (2) Phillips screws securing the hazard switch to the radio/climate control panel.
PAGE 5
99-7871 KIT ASSEMBLY DIN HEAD UNIT PROVISION NOTE: Secure the a/c vent, climate control, hazard switch, and the passenger air bag on/off light into the 99-7871 radio housing panel using the factory hardware. (FigureA1) Position the (6) metal factory retaining clips and (5) plastic white clips onto the radio housing in the same location as the factory radio/climate control panel. (Figure A2) 1 2 A1 A2 Slide the pocket into the bottom section of the kit housing.
PAGE 6
99-7871 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION NOTE: Secure the a/c vent, climate control, hazard switch, and the passenger air bag on/off light into the 99-7871 radio housing panel using the factory hardware. (Figure A1) Position the (6) metal factory retaining clips and (5) plastic white clips onto the radio housing in the same location as the factory radio/climate control panel. (Figure A2) A1 A2 Slide the pocket into the bottom section of the kit housing.
PAGE 7
99-7871 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION NOTE: Secure the a/c vent, climate control, hazard switch, and the passenger air bag on/off light into the 99-7871 radio housing panel using the factory hardware. (Figure A1) Position the (6) metal factory retaining clips and (5) plastic white clips onto the radio housing in the same location as the factory radio/climate control panel. (Figure A2) A1 A2 Remove the center bar from the 997871 radio housing.
PAGE 8
99-7871 KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION NOTE: Secure the a/c vent, climate control, hazard switch, and the passenger air bag on/off light into the 99-7871 radio housing panel using the factory hardware. (Figure A1) Position the (6) metal factory retaining clips and (5) plastic white clips onto the radio housing in the same location as the factory radio/climate control panel. (Figure A2) 1 Remove the center bar from the 997871 radio housing.
PAGE 9
9-7871 KIT ASSEMBLY STACKED DIN HEAD UNIT PROVISION A1 NOTE: Secure the a/c vent, climate control, hazard switch, and the passenger air bag on/off light into the 99-7871 radio housing panel using the factory hardware. (Figure A1) Position the (6) metal factory retaining clips and (5) plastic white clips onto the radio housing in the same location as the factory radio/climate control panel. (Figure A2) Slide the DIN cages into the Radio Housing and secure by bending the metal locking tabs outward.
PAGE 10
99-7871 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 11
99-7871 NOTES 9