Specifications

ManualsBrandsMetra Manualschassis components99-7862

INSTALLATION INSTRUCTIONS FOR PART 99-7862

Phillips Screwdriver • Small Flat Blade Screwdriver Or Panel Removal Tool

1-800-221-0932 www.metraonline.com

KIT FEATURES

APPLICATIONS

Honda Accord

2003-2007

• DIN Head Unit Provision with pocket

• ISO DIN Head Unit Provision with pocket

A) Radio Housing • B) ISO Brackets • C) ISO Trimplate • D) Radio Harness

KIT COMPONENTS

TOOLS REQUIRED:

99-7862

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7862 APPLICATIONS Honda Accord 2003-2007 99-7862 KIT FEATURES • DIN Head Unit Provision with pocket • ISO DIN Head Unit Provision with pocket KIT COMPONENTS A) Radio Housing • B) ISO Brackets • C) ISO Trimplate A B • D) Radio Harness C D TOOLS REQUIRED: Phillips Screwdriver • Small Flat Blade Screwdriver Or Panel Removal Tool 1-800-221-0932 www.metraonline.
PAGE 2
99-7862 TABLE OF CONTENTS Dash Disassembly - Honda Accord 2003-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . 1, 2 Kit Assembly - DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7862 DASH DISASSEMBLY HONDA ACCORD 2003-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove shift lever trim ring. (Figure A) 3 4 A R N D D Unsnap coin tray/ashtray from assembly and remove. Rubber cover may come out first but entire assembly must be removed to access screws below. (Figure B) B Remove (2) Phillips screws from under coin tray/ashtray and remove entire assembly.
PAGE 4
99-7862 DASH DISASSEMBLY HONDA ACCORD 2003-2007 5 Remove (2) Phillips screws from bottom of pocket assembly and unsnap and remove. (Figure D) 6 Remove (2) Phillips screws facing up under radio/climate control assembly. (Figure E) 7 Unsnap and remove upper panel (including a/c vents) and remove (3) Phillips screws behind the panel. (Figure F) D P D E Tip: You can use a hook tool to grasp the panel inside of the vent and pull toward the rear of the vehicle. Be careful not to scratch the panel.
PAGE 5
99-7862 KIT ASSEMBLY DIN HEAD UNIT PROVISION 1 A Snap the DIN cage into the Radio Housing and secure by bending the metal locking tabs down.. (Figure A) 2 Slide the aftermarket radio into the cage and secure. (Figure B) 3 Skip to step #1 in the Final Assembly.
PAGE 6
99-7862 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage. Snap the Trim plate into the Radio Housing. (Figure B) 3 Skip to step #1 in the Final Assembly.
PAGE 7
99-7862 FINAL ASSEMBLY FINAL ASSEMBLY A B C A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape D 1 Make the wiring connections from the radio harness included with this kit to the harness included with your radio using the EIA color code shown below. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Unplug factory harness from factory radio and plug the new harness in between the factory harness and the factory radio.
PAGE 8
99-7862 INSTRUCTIONS 1-800-221-0932 REV. 06/19/07 www.metraonline.