Specifications

ManualsBrandsMetra Manualschassis components99-7860

INSTALLATION INSTRUCTIONS FOR PART 99-7860

99-7860

APPLICATIONS

Honda Civic SI

2002-2005

(US Models Only)

KIT FEATURES

• DIN Head Unit Provision With Pocket

• ISO DIN Head Unit Provision With Pocket

• Stacked ISO Head Unit Provision

• Double DIN Head Unit Provision

• A) Single DIN Radio Housing • B) ISO Brackets • C) ISO Trim Plate

• D) Double DIN Trim Plate

KIT COMPONENTS

• Phillips Screwdriver • Offset Tool (Not Pictured)

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Harness:

• 70-1721 - Honda/Acura harness 1998-up

Antenna Adapter

• Not Required

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7860 APPLICATIONS Honda Civic SI 2002-2005 (US Models Only) 99-7860 KIT FEATURES • DIN Head Unit Provision With Pocket • ISO DIN Head Unit Provision With Pocket • Stacked ISO Head Unit Provision • Double DIN Head Unit Provision KIT COMPONENTS • A) Single DIN Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Trim Plate B A C D WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-1721 - Honda/Acura harness 1998-up Antenna Adapter • Not R
PAGE 2
99-7860 TABLE OF CONTENTS Dash Disassembly - Honda Civic SI 2002-2005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO Din Head Unit Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . 3 - Double Din Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - Stacked ISO Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7860 DASH DISASSEMBLY Honda Civic SI 2002-2005 5 Remove (3) Philips screws securing the climate control pod to the back of the dash trim bezel and remove the pod. 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the shift knob and unsnap the shifter lever trim panel. 6 Remove (4) Phillips screws from each side securing the factory head unit and pocket to the bracket assembly and remove.
PAGE 4
99-7860 KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the DIN cage into the radio opening of the Housing and secure by bending the metal locking tabs down. (Figure A) A 2 Slide the DIN unit into the cage until it is secure. (Figure B) 3 Snap the housing assembley into the dash trim bezel. (Figure C) Continue to final assembly. B C Assembled kit.
PAGE 5
99-7860 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Align the holes in the ISO Snap-In Backets with the holes in the head unit and mount the brackets to the head unit with the screws supplied with the unit. (Figure A) A 2 Slide the head unit/bracket assembly into the radio opening until the side clips engage. (Figure B) 3 Snap the ISO trimplate over the head unit.
PAGE 6
99-7860 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Align the holes on the factory backet assembly with the holes on the aftermarket Double DIN head unit and mount with the screws supplied with the unit. (Figure A) A 2 Cut and remove the center rib (shaded) from the Double DIN Trimplate. (Figure B) 3 Snap the Double DIN Trimplate over the head unit. (Figure C) B Continue to final assembly. C Assembled kit.
PAGE 7
99-7860 KIT ASSEMBLY STACKED ISO HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Align the holes on the factory backet assembly with the holes on the aftermarket ISO head units and mount with the screws supplied with the unit. (Figure A) A 2 Snap the Double DIN Trimplate over the head unit. (Figure B) Continue to final assembly. B Assembled kit.
PAGE 8
99-7860 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.