Quick Start Guide

ManualsBrandsMetra ManualsCar Electronics & GPSMetra - Dash Kit for Select 2006-2008 Honda Pilot Vehicles - Black

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-7819

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Radio replacement pocket assembly

• Textured to match the factory ﬁnish

KIT COMPONENTS

• A) Radio trim panel • B) Radio replacement pocket assembly • C) Pocket • D) Radio brackets • E) Climate control brackets

• F) (10) #8 x 3/8” Phillips screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Socket wrench

TABLE OF CONTENTS

Dash Disassembly ...............................................2-3

Kit Preparation .......................................................4

Kit Assembly

–ISO DIN radio provision with pocket ..................4

–ISO DDIN radio provision .....................................5

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-1721

Antenna Adapter: 40-HD10

A B DC E

Honda Pilot (with factory navigation) 2006-2008

Summary of content (8 pages)

PAGE 1
99-7819 I N S TA L L AT I O N I N S T R U C T I O N S Honda Pilot (with factory navigation) 2006-2008 KIT FEATURES • ISO DIN radio provision with pocket • ISO DDIN radio provision • Radio replacement pocket assembly • Textured to match the factory finish WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: 70-1721 Antenna Adapter: 40-HD10 KIT COMPONENTS • A) Radio trim panel • B) Radio replacement pocket assembly • C) Pocket • D) Radio brackets • E) Climate control brackets • F) (10) #8 x 3/8”
PAGE 2
DASH DISASSEMBLY 4. Remove (4) screws and remove the NAV screen. (Figure C) 1. Remove (2) Philips screws from under the instrument cluster and remove the trim. (Figure A) 5. Remove (4) screws and remove the NAV screen bracket. (Figure D) 2. Unclip and remove the trim panel between the instrument cluster and the NAV screen trim panel. (Figure A) Continued on next page 3. Unclip and remove the NAV screen trim panel. (Figure B) 2 (Figure A) (Figure C) (Figure B) (Figure D) 1.800.221.
PAGE 3
DASH DISASSEMBLY 6. Remove the side trim panels from the sides of the radio. (Figure E) 8. Remove (4) screws and remove the radio climate assembly. (Figure G) 7. Remove (4) screws and remove the trim from around the radio including the ashtray. (Figure F) 9. Remove (2) Philips screws to remove the climate control from the radio/ bracket assembly. (Figure H) Continue to Kit Preparation (Figure E) (Figure G) (Figure F) (Figure H) REV.
PAGE 4
KIT PREPARATION 1. Attach the climate control brackets to the radio replacement pocket assembly with (2) of the included #8 x 3/8” screws. (Figure A) 2. Place the climate controls between the climate control brackets and secure with the factory hardware. (Figure B) 3. Re-connect the climate control and secure the new assembly into the dash with factory hardware. Continue to Kit Assembly (Figure A) 4 (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 5
KIT ASSEMBLY ISO DIN radio provision with pocket 5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS. Test the radio for proper operation. 1. Attach the radio brackets to the radio trim panel using (4) #8 x 3/8” Phillips screws supplied. (Figure A) 2. Attach the pocket to the bracket assembly using the (4) supplied #8 x 3/8” Phillips screws. (Figure B) 3.
PAGE 6
KIT ASSEMBLY ISO DDIN radio provision 1. Attach the radio brackets to the radio trim panel using (4) #8 x 3/8” Phillips screws supplied. (Figure A) 2. Slide the radio into the completed assembly, and then secure it to the assembly using the screws supplied with the radio. (Figure B) 3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS.
PAGE 7
REV.
PAGE 8
99-7819 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.