Specifications

ManualsBrandsMetra Manualschassis components99-7602

INSTALLATION INSTRUCTIONS FOR PART 99-7602

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Radio Provision with pocket

• ISO Radio Provision with pocket

• Two stacked ISO units provision

• Double DIN radio provision

Po et

A) Radio Housing with

TB) Double DIN

rim-plat

Bra k

C) ISO Snap-in c ets

•

D) ISO Trim-plate

KIT COMPONENTS

OOL

REQUIRE

99-7602

APPLICATIONS

350Z

2006-2008

Phillips

Scr

ewdrive

Nissan

Panel

or Small

Fla

Bla

ewdrive

•

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-7550 - Nissan harness 1995-up

• 70-7551 - Nissan amp interface harness 1995-up

Antenna Adapter:

• Not required

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7602 APPLICATIONS Nissan 350Z 2006-2008 99-7602 KIT FEATURES • DIN Radio Provision with pocket • ISO Radio Provision with pocket • Two stacked ISO units provision • Double DIN radio provision KIT COMPONENTS A) Radio Housing with Pocket A • B) Double DIN Trim-plate • C) ISO Snap-in Brackets • D) ISO Trim-plate B D C WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-7550 - Nissan harness 1995-up • 70-7551 - Nissan amp interface harness 1995-up Anten
PAGE 2
99-7602 TABLE OF CONTENTS Dash Disassembly Nissan 350Z 2006-2008.........................................................................1, 2 Kit Assembly Din Mount Radio Provision with pocket.................................................................3 ISO Mount Radio Provision with pocket.................................................................4 Double DIN Radio.....................................................................................................5 Two Stacked ISO mount units..
PAGE 3
99-7602 DASH DISASSEMBLY NISSAN 350Z 2006-2008 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 For vehicles with automatic transmission, Unsnap and remove smaller trim-ring from around shifter. (Figure A) For vehicles with manual transmission, Unscrew and remove shifter knob. (Figure A) 3 A B Unsnap and remove center console trim panel including climate controls. (Figure B) C 4 5 For vehicles with navigation, Unsnap and remove navigation switch panel.
PAGE 4
99-7602 DASH DISASSEMBLY NISSAN 350Z 2006-2008 6 Remove (2) screws above the radio and (2) screws below the radio. Also remove (2) screws securing the radio/trim panel assembly. (Figure E) 7 Unplug and remove the radio / trim panel assembly. (Figure F) 8 Remove (4) screws securing the radio to the trim panel and remove the radio. 9 Remove (8) screws securing the factory brackets to the radio and remove the brackets from the radio.
PAGE 5
99-7602 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET 1 Slide DIN cage (supplied with radio) into the radio housing from the front. (Figure A) 2 Secure DIN cage to radio housing by bending the locking tabs outward. (Figure A) A B 3 Slide the radio into the DIN cage until it snaps into place. (Figure B) 4 Attach the radio / housing assembly to the radio trim panel using the factory screws removed during disassembly. (Figure C) C Continue to final assembly.
PAGE 6
99-7602 KIT ASSEMBLY ISO MOUNT RADIO WITH POCKET A 1 Align the holes in the ISO brackets with the holes in the radio. Mount the brackets to the radio using screws supplied with the radio. (Figure A) 2 Slide the radio bracket assembly into the radio housing until it snaps into place. (Figure B) 3 Snap the ISO trim-plate onto the front of the assembled radio and housing. (Figure B) 4 Attach the radio / housing assembly to the radio trim panel using the factory screws removed during disassembly.
PAGE 7
99-7602 KIT ASSEMBLY DOUBLE DIN RADIO 1 Cut and remove center divider from double DIN trim-plate. (Figure A) 2 Place the double DIN trim-plate on the front of the radio. (Figure B) 3 Place the right factory mounting bracket (Removed from radio during disassembly) on the right side of the radio. Align the pins on the trim-plate with the holes on the factory bracket and mount the factory bracket to the radio using screws supplied with the radio.
PAGE 8
99-7602 KIT ASSEMBLY TWO STACKED ISO MOUNT UNITS 1 Place the double DIN trim-plate on the front of the two ISO units. (Figure A) 2 Place the right factory mounting bracket (Removed from radio during disassembly) on the right side of the ISO units. Align the pins on the trim-plate with the holes on the factory bracket and mount the factory bracket to the ISO units using screws supplied with the radio.
PAGE 9
9-7602 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 10
99-7602 NOTES 8
PAGE 11
99-7602 NOTES 9
PAGE 12
99-7602 INSTRUCTIONS 1-800-221-0932 REV. 08/11/09 www.metraonline.