Specifications

ManualsBrandsMetra Manualschassis components99-7510

INSTALLATION INSTRUCTIONS FOR PART 99-7510

99-7510/

99-7510HG

APPLICATIONS

Mazda RX-8

2004-2008

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• TWO FINISHES

AVAILABLE:

99-7510=BLACK, 99-7510HG=GLOSS BLACK

• A) Radio / Climate Control Housing • B) ISO Brackets • C) ISO Trim Plate

• D) Interface • E) Wiring Harnesses • F) (2) Climate Control Extension Harnesses

KIT COMPONENTS

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set • Cutting Tool

1-800-221-0932

TION

www.metr

aonline.com

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7510 APPLICATIONS Mazda RX-8 2004-2008 99-7510/ 99-7510HG KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • TWO FINISHES AVAILABLE: 99-7510=BLACK, 99-7510HG=GLOSS BLACK KIT COMPONENTS • A) Radio / Climate Control Housing • B) ISO Brackets • C) ISO Trim Plate • D) Interface • E) Wiring Harnesses • F) (2) Climate Control Extension Harnesses C B A D F E TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phill
PAGE 2
99-7510 TABLE OF CONTENTS Dash Disassembly - Mazda RX-8 2004-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2,3 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 5 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
AC FM1 877 99-7510 DASH DISASSEMBL Y MAZDA RX-8 2004-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unscrew the shift knob counter clockwise to remove. (Figure A) 3 Unclip and remove the shifter trim panel. (Figure B) 4 Remove (2) Phillips screws from the bottom of the ashtray assembly then unclip and remove the assembly.
PAGE 4
99-7510 DASH DISASSEMBLY MAZDA RX-8 2004-2008 E 6 Remove (2) Phillips screws from the bottom of the radio/climate control panel. (Figure F) FM1 877 7 Unsnap radio/climate control panel including radio chassis. Unplug and remove panel and chassis. (Figure G) 8 Remove (3) Phillips screws securing the factory display harness to the radio chassis. Unplug and remove display harness. (Retain display harness for re-use during kit assembly.
PAGE 5
99-7510 DASH DISASSEMBLY MAZDA RX-8 2004-2008 I 11 Remove (17) screws securing the circuit board to the radio/climate control panel to access the plug for the hazard switch assembly. (Figure K) 12 Remove (2) screws securing the hazard switch to the radio/climate control panel. Unplug and remove hazard switch. (Retain the screws and hazard switch for re-use during kit assembly.) (Figure L) Continue to kit assembly.
PAGE 6
99-7510 KIT PREPARATION MAZDA RX-8 2004-2008 *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut the top (2) mounting locations off of the climate controls to provide clearance for the aftermarket radio. (Figure A) 2 Secure the climate control to the radio/climate control housing using (4) of the factory screws removed in step (10) of the dash disassembly.
PAGE 7
99-7510 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the DIN cage into the Radio/Climate Control Housing and secure by bending the metal locking tabs outward. (Figure A) A 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly. B ISO MOUNT RADIO PROVISION WITH POCKET 1 Mount the ISO Brackets to the radio using the screws supplied with the radio.
PAGE 8
99-7510 FINAL ASSEMBLY FINAL ASSEMBLY A B (A) Strip wire ends back 1/2" B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Use the supplied wire harnesses and make the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). Refer to Metra/EIA Wiring Code below.
PAGE 9
9-7510 FINAL ASSEMBLY Continued from Page 6 WARNING! FAILURE TO INSERT THE HVAC CABLES INTO THE CORRECT LOCATION WILL CAUSE DAMAGE TO THE INTERFACE AND MAKE THE DISPLAY AND HVAC CONTROLS NOT FUNCTION PROPERLY 2 Attach the (2) climate control extension harnesses to the temperature control cable and the fan control cable on the factory climate control. 3 Plug the Temperature Control cable from the factory climate control into the port on the interface that reads “TEMP”.
PAGE 10
99-7510 FINAL ASSEMBLY Continued from Page 7 A OBDII CONNECTOR FACE VIEW PINK WIRE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PINK/BLUE WIRE 7 When using the Nav features of the interface you will need to connect the 2 pin harness and run the 2 wires to the OBDII connector and connect them in the position shown. (Figure A) 8 The following wires on the 10 pin harness are for the aftermarket radios that have navigation built in: A.
PAGE 11
OPEN TILT 877 AC 99-7510 DISPLAY OPTIMIZATION FM1 DISPLAY CUSTOMIZATION *Note: Refer also to the instructions included with the aftermarket radio. 1 2 0 3 A/C 4 OPEN TILT FM1 MODE 877 AC 1 Press and hold the A/C Mode button to scroll through the various kit options (AMB TEMP ON or OFF, AMB TEMP C or F, SET TIME 12/24H, and SET TEXT). 2 When you see the option you want just let the button go and the action on the screen will be performed.
PAGE 12
99-7510 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.