User Manual

ManualsBrandsMetra ManualsCar Electronics & GPSMetra - Dash Kit for Select 2017-2018 Kia Sportage Vehicles - Black

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

99-7390B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) Climate display • E) (2) #8 x 3/8” Phillips screws • F) Wiring harness (not shown)

Kia Sportage (with NAV) 2017-2018

A CB D

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Includes an AX-CAM6V, antenna adapter, and wiring harness for a

complete installation

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Pick tool

TABLE OF CONTENTS

Dash Disassembly ...............................................2-3

Kit Preparation ...................................................4-6

Kit Assembly ..........................................................7

Wiring Instructions ...........................................8-15

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Interface and harness included

Antenna Adapter: Included with kit

Steering wheel control interface: Included with kit

12v to 6v camera step-down: included with kit

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (16 pages)

PAGE 1
99-7390B I N S TA L L AT I O N I N S T R U C T I O N S Kia Sportage (with NAV) 2017-2018 Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. Unclip and slide the top of the center console back slightly. (Figure A) 3. Unclip the panel above the glove box. Unplug the passenger airbag light, then remove the panel. (Figure C) 2. Unclip and remove the panel on the end of the passenger side of the dash, then remove (1) Phillips screw exposed. (Figure B) 4. Remove (2) Phillips screws securing the radio display and a/c vent panel, then unclip and remove the panel.
PAGE 3
DASH DISASSEMBLY 5. Remove (4) Phillips screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure E) (CONT.) 7. Remove (1) Phillips screw securing the lower right side drivers knee bolster. Unsnap the bolster just enough to access the (1) Phillips screw securing the climate control panel, then remove the screw. (Figure G) 6. Remove (3) Phillips screw securing the climate control panel. (Figure F) 8.
PAGE 4
KIT PREPARATION Radio Trim Panel Installation From the factory radio trim panel: 1. Remove (4) Phillips screws securing the inner trim panel, then remove the panel. (Figure A) To the factory radio trim panel: 2. Secure the 99-7390B radio trim panel to the panel using with the factory screws. (Figure B) Continued on the next page (Figure A) 4 (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 5
KIT PREPARATION (CONT.) Climate Display Installation 1. Remove (4) Phillips screws securing the radio/hazard assembly to the climate/ radio control panel, then unclip and remove the assembly. (Figure C, heavier arrows) 2. Remove (9) Phillips screws securing the back cover to the radio/hazard assembly, then remove the cover. (Figure C) (Figure D) 3. Using a pick tool, gently release (4) clips holding the hazard switch to the assembly, then remove the switch.
PAGE 6
KIT PREPARATION (CONT.) 4. Clip the hazard switch into the climate display. (Figure E) 5. Secure the climate-display/hazardswitch assembly to the climate control panel using the factory screws. (Figure F) Continue to Kit Assembly (Figure F) (Figure E) 6 1.800.221.0932 | MetraOnline.
PAGE 7
KIT ASSEMBLY ISO DIN radio provision with pocket ISO DDIN radio provision 1. Secure the radio brackets to the pocket using the (2) #8 x 3/8” Phillips screws provided. (Figure A) 1. Secure the radio brackets to the radio using the screws supplied with the radio. (Figure A) 2. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3. Slide the radio into the bracket/pocket assembly, then secure it to the assembly using the screws supplied with the radio.
PAGE 8
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES • Retains audio controls on the steering wheel • Provides NAV outputs (parking brake, reverse, speed sense) • Retains the factory AUX-IN jack • Retains the factory backup camera • Includes an AX-CAM6V 12-to-6V step-down for the factory camera • Retains balance • Micro “B” USB updatable INTERFACE COMPONENTS • Axxess interface • AX-HYKIA-SPDIF interface • AX-CAM6V • 7390 harness • 16-pin harness with stripped leads • Female 3.
PAGE 9
CONNECTIONS From the 16-pin harness with stripped leads to the aftermarket radio: From the 7390 harness to the aftermarket radio: • Connect the Red wire to the accessory wire. • Connect the Black wire, and also the Black wire from the AX-CAM6V, to the ground wire. • Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier. • Connect the Yellow wire to the battery wire. • Connect the Gray wire to the right front positive speaker output.
PAGE 10
CONNECTIONS (CONT.) INSTALLATION 3.5mm jack steering wheel control retention: With the key in the off position: The 3.5mm jack is to be used to retain audio controls on the steering wheel. 1. Connect the 16-pin harness with stripped leads, and the 7390 harness, into the interface. • For the radios listed below, connect the female 3.5mm connector with stripped leads, to the male 3.5mm SWC jack from the 7390 harness.
PAGE 11
PROGRAMMING THE INTERFACE AND CLIMATE DISPLAY Programming the interface: Programming the climate display: For the steps below, the L.E.D. located inside the interface can only be seen while active. The interface does not need to be opened to see the L.E.D. 7. Turn the parking lights on. • Start the vehicle. 9. Turn the lights off. 8. Turn the vehicles light dimmer all the way down, then all the way up. • Connect the 7390 harness to the wiring harness in the vehicle. • The L.E.D.
PAGE 12
STEERING WHEEL CONTROL SETTINGS L.E.D. feedback The (18) Red L.E.D. flashes represent what brand radio the ASWC-1 believes it is connected to. Each flash represents a different radio Manufacturer. For example, if you are installing a JVC radio, the ASWC-1 will flash Red (5) times, and then stop. Following is a legend that dictates which radio Manufacturer corresponds to which flash. L.E.D.
PAGE 13
STEERING WHEEL CONTROL SETTINGS Changing radio type If the L.E.D. flashes do not match the radio you have connected, you must manually program the Axxess interface to tell it what radio it is connected to. 1. After (3) seconds of turning the key on, press and hold the “Volume-Down” button on the steering wheel until the L.E.D. in the Axxess interface goes solid. 2. Release the “Volume-Down” button; the L.E.D. will go out indicating the Axxess interface is in “Changing Radio Type” mode. 3.
PAGE 14
STEERING WHEEL CONTROL SETTINGS Remapping the steering wheel control buttons Once the ASWC-1 has been programmed, the button assignment for the steering wheel controls may be reassigned if so desired. For example, if the “Seek-Up” button is preferred to be the “Mute” button instead. Follow the steps below to remap the steering wheel control buttons. 1. Ensure the Axxess interface is visible so you can see the L.E.D. flashes to confirm button recognition. Tip: Turning the radio off is recommended. 2.
PAGE 15
STEERING WHEEL CONTROL SETTINGS Dual assignment instructions (long button press) The ASWC-1 has the capability to assign (2) functions to a single button, except “Volume-Up” and “Volume-Down”. Follow the steps below to program the button(s) to the desired setting. Note: “Seek-Up” and “Seek-Down” come pre-programmed as “Preset-Up” and “Preset-Down” for a long button press. 1. Turn the key to ignition but do not start the vehicle. 2.
PAGE 16
99-7390B I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.