User Manual

ManualsBrandsMetra ManualsCar Electronics & GPSMetra - Dash Kit for Select 2018 Hyundai Sonata Vehicles - Silver/Matte Black

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-7383

KIT FEATURES

• ISO DIN radio provision with pocket

• Painted matte black and silver

KIT COMPONENTS

• A) Radio trim panel A • B) Radio trim panel B • C) Radio brackets • D) Pocket • E) (4) #8 x 3/8” Phillips screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Cutting tool

TABLE OF CONTENTS

Dash Disassembly ...............................................2-3

Kit Preparation .......................................................4

Kit Assembly ..........................................................5

A B C D E

Hyundai Sonata 2018-up*

*Visit MetraOnline.com for up-to-date vehicle speciﬁc applications.

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: Please visit metraonline.com

for wiring harness options

Antenna Adapter: Please visit metraonline.com

for antenna adapter options

Summary of content (8 pages)

PAGE 1
99-7383 I N S TA L L AT I O N I N S T R U C T I O N S Hyundai Sonata 2018-up* TABLE OF CONTENTS Dash Disassembly................................................2-3 Kit Preparation........................................................4 Kit Assembly...........................................................5 *Visit MetraOnline.com for up-to-date vehicle specific applications.
PAGE 2
DASH DISASSEMBLY 1. Unsnap and remove the climate/ hazard/clock panel. (Figure A) 3. Unclip and remove the panel below the left a/c vent, then remove (1) Phillips screw. (Figure C) 2. Unsnap and remove the trim panel on the drivers side of the dash and then remove (2) Phillips screws. (Figure B) 4. Unsnap the knee panel from under the steering wheel. (no need to completely remove this panel). (Figure D) Continued on the next page 2 (Figure A) (Figure C) (Figure B) (Figure D) 1.800.221.
PAGE 3
DASH DISASSEMBLY (CONT.) 5. Unsnap and remove the panel above the instrument cluster. (Figure D) 6. Unsnap the top half of the steering column cover. (Figure E) 7. Remove (4) screws to remove the radio panel; (2) under the radio section, and (2) above the instrument cluster. (Figure F) Note: The top of the steering column cover will come with the large panel. 8. Remove (4) Phillips screws securing the radio and then remove the radio. (Figure D) (Figure E) (Figure F) Continue to Kit Preparation REV.
PAGE 4
KIT PREPARATION Attention! The factory panel will be permanently modified after following these steps. 1. Remove (4) Phillips screws securing the bottom of the vents, then unsnap and remove them. 2. Remove (7) Phillips screws securing the radio trim panel to the radio panel, then remove the trim panel. (Figure A) 3. Cut the opening as shown (front of dash panel shown) to allow room for the new radio trim panel. (Figure B) (Figure A) 4.
PAGE 5
KIT ASSEMBLY ISO DIN radio provision with pocket 1. Secure the pocket to the radio brackets using the (4) #8 x 3/8” Phillips screws supplied. (Figure A) 2. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3. Slide the radio into bracket/pocket assembly and secure with screws supplied with the radio. (Figure B) 4. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio.
PAGE 6
1.800.221.0932 | MetraOnline.
PAGE 7
REV.
PAGE 8
99-7383 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.