Installation Guide

ManualsBrandsMetra ManualsOtherMeTra 99-7349B Single Dash Kit

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-7349B

U.S. Patent # D716,791

KIT FEATURES

• DIN radio provision with pocket

• Painted matte black

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly ..........................................................3

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-7304 • AX-HYKIA1-SWC

& AX-HYKIA-SPDIF (for ampliﬁed models)

Antenna Adapter: Not required

A B C D

Kia Soul 2012-2013

Summary of content (8 pages)

PAGE 1
99-7349B I N S TA L L AT I O N I N S T R U C T I O N S U.S. Patent # D716,791 Kia Soul 2012-2013 KIT FEATURES • DIN radio provision with pocket • Painted matte black KIT COMPONENTS • A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws A B C TABLE OF CONTENTS Dash Disassembly ..................................................2 Kit Assembly ..........................................................
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove the panel (and speaker if equipped) from above the radio panel. (Figure A) 3. Remove (4) Phillips screws securing the climate control panel. Slide the panel out and set to the side. (Figure C) 2. Unclip and remove the radio/climate control trim panel. (Figure B) 4. Remove (4) Phillips screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure C) (Figure A) 5.
PAGE 3
KIT ASSEMBLY 1. Secure the radio brackets to the pocket using the (4) #8 x 3/8” Phillips screws provided. (Figure A) 2. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3. Slide the radio into the bracket/pocket assembly, then secure it using the screws supplied with the radio. (Figure B) 4. Clip the radio trim panel over the radio/ pocket/bracket assembly. (Figure B) (Figure A) (Figure B) 5. Locate the factory wiring harness and antenna connector in the dash.
PAGE 4
99-7349B I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
PAGE 5
99-7349B I N S T R U C C I O N E S D E I N S TA L AC I Ó N U.S. Patent # D716,791 Kia Soul 2012-2013 CARACTERÍSTICAS DEL KIT • Provisión de radio DIN con cavidad • Pintura negro mate COMPONENTES DEL KIT • A) Panel de moldura de radio • B) Soportes del radio • C) Cavidad • D) (4) Tornillos Phillips #8 de 3/8” A B C D INDICE Desmontaje del tablero ........................................2 Ensamble del kit ....................................................
PAGE 6
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel (y la bocina, si se incluye), de arriba del panel del radio. (Figura A) 3. Quite los (4) tornillos Phillips que sujetan el control de clima. Deslice el panel y colóquelo hacia un lado. (Figura C) 2. Desenganche y quite el panel de la moldura del radio/control de clima. (Figura B) 4. Quite los (4) tornillos Phillips que sujetan el radio. Deslice el radio hacia afuera, luego desconecte y retire la radio. (Figura C) (Figura A) 5.
PAGE 7
ENSAMBLE DEL KIT 1. Atornille los soportes del radio al cavidad con los (4) tornillos Phillips #8 de 3/8” suministrados. (Figura A) 2. Quite la manga de metal DIN y el anillo de moldura del radio de mercado secundario. 3. Deslice el radio dentro del ensamble del soporte/cavidad, luego sujételo con los tornillos suministrados con el radio. (Figura B) 4. Clip del panel de moldura de radio sobre el ensamble de cavidad/soporte. (Figura B) (Figura A) (Figura B) 5.
PAGE 8
99-7349B I N S T R U C C I O N E S D E I N S TA L AC I Ó N IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.