Specifications

ManualsBrandsMetra Manualschassis components99-7012

INSTALLATION INSTRUCTIONS FOR PART 99-7012

99-7012

MITSUBISHI Galant 2004-2010

(

with auto climate control)

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Snap in Pocket

Har

ness & Antenna Connections (sold separately)

•70-7001 - Mitsubishi Harness 92-up

KIT COMPONENTS

Phillips Screwdriver/ Panel Removal Tool

• Socket Set • Cutting Tool

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7012 APPLICATIONS MITSUBISHI Galant 2004-2010 (with auto climate control) 99-7012 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Snap in Pocket B C D E A Harness & Antenna Connections (sold separately) •70-7001 - Mitsubishi Harness 92-
PAGE 2
99-7012 TABLE OF CONTENTS Dash Disassembly - Mitsubishi Galant 2004-2010(with auto climate control) . . . . . . .1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN Radio Provision/Stacked ISO Mount Units Provision . . . . . . 4 Final Assembly . .
PAGE 3
99-7012 DASH DISASSEMBLY MITSUBISHI GALANT 2004-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the radio trim panel including the climate controls and radio controls. Unplug and remove the panel. (Figure A) 3 Remove (4) Phillips screws securing radio chassis to sub dash. Unplug and remove the chassis. (Figure B) 4 Remove (4) Phillips screws securing the climate controls to the radio panel.
PAGE 4
99-7012 KIT PREPARATION A 1 Secure the climate controls to the radio housing using the factory hardware. (Figure A) 99-7012 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the DIN cage into the radio housing and secure by bending the metal locking outward. (Figure A) A 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing.
PAGE 5
99-7012 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio/bracket assembly into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the radio housing. (Figure B) 4 Snap the Pocket into the radio housing. (Figure C) B Continue to final assembly.
PAGE 6
99-7012 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing.
PAGE 7
99-7012 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 8
99-7012 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.