User Manual

ManualsBrandsMetra ManualsCar Electronics & GPSMetra - Dash Kit for Select 2015 Ford Mustang Vehicles - Charcoal

REV. 2/7/2017 INST99-5838CH

INSTALLATION INSTRUCTIONS FOR PART 99-5838CH

METRA – The World’s best kits.

metraonline.com

CAUTION!

All accessories, switches, climate controls panels,

and especially air bag indicator lights must be connected before

cycling the ignition. Also, do not remove the factory radio with

the key in the on position, or while the vehicle is running.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted Charcoal

• Touchscreen display for climate and

personalization features

• A) Radio trim panel with touchscreen display • B) Radio brackets • C) SYNC module brackets • D) Pocket

• E) Engine start/stop circuit board and cover • F) Engine start/stop trim • G) (4) #8 x 3/4” Phillips pan-head screws

• H) (4) #8 x 3/8” Phillips truss-head screws • I) (6) #4 x 1/2” Phillips pan-head screws • J) (4) Panel clips • K) USB cable

• L) HV

AC interface and wiring harness (not shown)

KIT FEATURES

KIT COMPONENTS

• Panel removal tool • Phillips screwdriver

• 9/32” socket wrench • Cutting tool

• Torx T-10 screwdriver

TOOLS REQUIRED

Ford Mustang 2015-up

(with 4.2” screen)

99-5838CH

Table of Contents

A B C D E

GF H J K

Dash Disassembly ..............................................2-4

Kit Preparation ....................................................5-7

Kit Assembly

– ISO DIN radio provision with pocket ...................... 8

– ISO DDIN radio provision ...................................... 8

Axxess Interface Installation ...........................9-17

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess interface and harness included

Antenna Adapter: 40-EU10 (sold separately)

Summary of content (20 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-5838CH Ford Mustang 2015-up Table of Contents (with 4.2” screen) Dash Disassembly...............................................2-4 Kit Preparation.....................................................5-7 Kit Assembly 99-5838CH REV. 2/7/2017 INST99-5838CH KIT FEATURES • ISO DIN radio provision with pocket • ISO DDIN radio provision • Painted Charcoal • Touchscreen display for climate and personalization features –. ISO DIN radio provision with pocket.............
PAGE 2
99-5838CH Dash Disassembly 1. Open the passenger door and remove the trim panel from the side of the dash. (Figure A) 2. Open the glove box and remove the trim panel on the right side. (Figure B) 3. Unclip and remove the trim/vent dash panel.
PAGE 3
99-5838CH Dash Disassembly (cont.) 4. Remove the rubber tray cover in front of the shifter, and then remove the (2) 9/32” screws exposed. (Figure D) 5. Unclip and remove the front side panels from each side of the center console. (Figure E) 6. Remove the (2) 9/32” screws from each side of the center console.
PAGE 4
99-5838CH Dash Disassembly (cont.) 7. Unclip the shifter trim bezel and slightly pull it up to clear the center console removal. Ensure that the vehicle is completely off before proceeding onto the following (3) steps: 8. Open the center console storage compartment, unclip the top of the console, and then slide it toward the rear of the vehicle to remove it. (Figure G) 11. Remove the (4) 9/32” screws securing the radio/climate control panel, and then unclip, unplug, and remove. (Figure I) 12.
PAGE 5
99-5838CH Kit Preparation 1. Cut and remove the shaded area from the sub-dash to allow clearance for the aftermarket radio. (Figure A) If SYNC is desired to be retained: 2. Attach the SYNC module brackets to the factory SYNC module using the (4) #8 x 3/4” Phillips pan-head screws provided. (Figure B) 4. Re-connect all factory connectors back into the SYNC module, and then secure the module into the lower sub-dash using the factory hardware removed in step 13.
PAGE 6
99-5838CH Kit Preparation From the factory radio/climate control panel: (cont.) 3. Remove the rubber button membrane from the back of the engine start/stop switch panel. (Figure C) 1. Remove the (15) T-10 Torx screws securing the plastic panel cover to the rear of the panel, and then remove. (Figure A) 4. Remove the engine start/stop switch panel. (Figure D) 2. Remove the (7) T-10 Torx screws securing the circuit board, and then remove. (Figure B) 5.
PAGE 7
99-5838CH Kit Preparation (cont.) 3. Insert the USB cable into the USB slot, through the rear. (Figure C) To the 99-5838CH radio trim panel: 1. Attach the engine start/stop trim, engine start/stop switch panel, and then the rubber button membrane. (Figure A) 4. Attach the (4) panel clips provided. (Figure D) Continue to Kit Assembly 2. Secure the engine start/stop circuit board and cover to the switch/ cover assembly using the (6) #4 x 1/2” Phillips pan-head screws provided.
PAGE 8
99-5838CH Kit Assembly ISO DIN radio provision with pocket ISO DDIN radio provision 1. Attach the pocket to the radio brackets using the (4) #8 x 3/8” Phillips truss-head screws provided. (Figure A) 1. Attach the brackets to the radio using the screws supplied with the radio. (Figure A) Continue to Axxess Interface Installation 2. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3.
PAGE 9
9-5838CH Axxess Interface Installation INTERFACE FEATURES • Provides accessory power (12-volt 10-amp) • Retains R.A.P. (retained accessory power) • Provides NAV outputs (parking brake, reverse, speed sense) • Retains audio controls on the steering wheel • Retains SYNC • Retains the factory backup camera • Retains balance and fade • Micro “B” USB updatable TABLE OF CONTENTS Connections to be made....................................................................... 10-12 Installing the interface.........
PAGE 10
99-5838CH Connections to be made From the 16-pin harness with stripped leads to the aftermarket radio: From the 5838 harness to the aftermarket radio: • Connect the Red wire to the accessory wire. • Connect the Black wire to the ground wire. • If the aftermarket radio has an illumination wire, connect the Orange/White wire to it. • Connect the Yellow wire to the battery wire. • Connect the Blue wire to the power antenna wire. • Connect the Gray wire to the right front positive speaker output.
PAGE 11
99-5838CH Connections to be made 3.5mm jack - steering wheel control retention: • The 3.5mm jack is to be used to retain audio controls on the steering wheel control. • For the radios listed below, connect the included female 3.5mm connector with stripped leads, to the male 3.5mm SWC jack from the 5838 harness. Any remaining wires tape off and disregard. • Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire of the connector.
PAGE 12
99-5838CH Connections to be made (cont.) 4-pin harness with yellow RCA jacks: 3. Connect the 4-pin harness with yellow RCA jacks into port “C” in the touchscreen display. 4. Disregard ports “D” and “E”, they will not be used in this application. 5. Port “F” is an update port for future firmware upgrades. • If retaining the factory backup camera to the touchscreen display is desired, connect the Yellow RCA jack labeled “Rearview camera”, to the Yellow RCA jack from the 12-pin backup camera harness.
PAGE 13
99-5838CH Installing the interface (cont.) 7. Connect the male DIN connector with a 6-pin harness, to the female DIN jack from the 5838 harness. It would be best to tape or heat shrink this connector to prevent it from being disconnected. a. Then connect the 6-pin harness into the HVAC interface. b. Disregard the Red wire, it will not be used in this application.
PAGE 14
99-5838CH Touchscreen display operation HVAC Control screen Touchscreen calibration: • Press and hold the upper two soft buttons on either side of the touchscreen for 10 seconds. • A screen will pop up asking for you to press the target in the screen. • After pressing the target with your finger, the calibration process will be complete, and the screen will disappear. Continued on the next page • This is the HVAC control screen which will be displayed on the touchscreen display.
PAGE 15
99-5838CH Touchscreen display operation (cont.
PAGE 16
99-5838CH Steering wheel control settings Select Radio screen * Note: If the interface shows an Alpine radio, and you do not have an Alpine radio, that means the interface does not detect a radio connected it, i.e., an open connection. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio. ** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated to rev. 2.1.4 or higher through www.parrot.com.
PAGE 17
99-5838CH Steering wheel control settings (cont.) Remap Button screen Dual Assign screen • The interface has the ability to change the button assignment for the steering wheel control audio buttons, except Volume-Up and Volume-Down. Follow the prompts on the touchscreen display to remap the steering wheel control audio button(s) to your liking. • The interface has the capability to assign two functions to a single button, except Volume-Up and Volume-Down.
PAGE 18
99-5838CH 18
PAGE 19
99-5838CH 19
PAGE 20
INSTALLATION INSTRUCTIONS FOR PART 99-5838CH IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.