Datasheet

ManualsBrandsMetra Manualschassis components99-5820B

INSTALLATION INSTRUCTIONS FOR PART 99-5820

99-5820

KIT FEATURES

• DIN Radio Provision With Pocket

• ISO Mount Radio Provision With Pocket

• A) Radio Housing Trim Panel • B) Radio Housing Brackets • C) Radio Housing

• D) (6) U Style Panel Clips • E) ISO Trim Plate • F) ISO Brackets

KIT COMPONENTS

1-800-221-0932

www.metraonline.com

APPLICATIONS

Ford

F-150 2009-up

Cutting Tool • Phillips Screwdriver • Socket Wrench • Torx Driver

Panel Removal Tool

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Harness

• Please see www.metraonline.com for

specific interface harness

Antenna Adapter:

• 40-CR10 - Chrysler antenna adapter 02-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-5820 APPLICATIONS Ford F-150 2009-up 99-5820 KIT FEATURES • DIN Radio Provision With Pocket • ISO Mount Radio Provision With Pocket KIT COMPONENTS • A) Radio Housing Trim Panel • B) Radio Housing Brackets • C) Radio Housing • D) (6) U Style Panel Clips • E) ISO Trim Plate • F) ISO Brackets B A E C D WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • Please see www.metraonline.
PAGE 2
99-5820 TABLE OF CONTENTS Dash Disassembly - FORD F-150 2009-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Preparation - FORD F-150 2009-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Assembly - DIN Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . 5 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-5820 DASH DISASSEMBLY FORD F-150 2009-UP A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the (1) 9/32” screw exposed. (Figure A) 3 Remove the rubber pad at the top of the radio trim panel then remove the (2) 9/32” screws exposed. (Figure B) 4 Unclip and pull the side panels containing the a/c vents away from the radio trim panel.
PAGE 4
99-5820 DASH DISASSEMBLY FORD F-150 2009-UP E 6 Unclip and remove the hazard/airbag switch assembly from the factory radio trim panel. (Figure E) 7 Unclip and remove the cigarette lighter socket from the radio trim panel. (Figure F) 8 Remove (4) Torx screws securing the factory climate control to the radio trim panel. (Figure G) F 9 Remove (4) 9/32” screws to remove the factory radio. Continue to kit preparation.
PAGE 5
99-5820 KIT PREPARATION FORD F-150 2009-UP A 1 Clip the hazard/airbag switch assembly into the radio housing in the same location as the factory radio trim panel. (Figure A) 2 Clip the cigarette lighter socket into the radio housing in the same location as the factory radio trim panel. (Figure B) 3 Secure the climate control into the radio housing using the factory hardware in the same location as the factory radio trim panel.
PAGE 6
99-5820 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the top (2) mounting holes off of the radio housing. Note: The notch in the housing should be on top. (Figure A) CUT HERE -TOP LEG ONLY CUT 2 Slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward.
PAGE 7
99-5820 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Cut and remove the top (2) mounting holes off of the radio housing. Note: The notch in the housing should be on top. (Figure A) A CUT HERE -TOP LEG ONLY CUT 2 Slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward.
PAGE 8
99-5820 FINAL ASSEMBLY FINAL ASSEMBLY A B (A) Strip wire ends back 1/2" B) Twist ends together C C) Solder D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). 2 Re-connect the negative battery terminal and test the unit for proper operation.