Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installationDash and Wiring Kit

Table Of Contents

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-3030B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Complete center dash panel for a factory look

• Painted matte black

• Includes an Axxess interface, wiring harness, ASWC-1,

and antenna adapter for a complete installation

KIT COMPONENTS

• A) Radio/climate control panel • B) Radio brackets • C) Climate control trim panel A (04-05) • D) Climate control trim panel B (06-09) • E) Pocket

• F) (6) Panel clips • G) (12) #8 x 3/8” Phillips screws • H) Axxess interface and wiring harness (not shown) • I) Antenna adapter (not shown)

• J) ASWC-1 (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 9/32” Socket wrench

TABLE OF CONTENTS

Dash Disassembly ...............................................2-3

Kit Preparation ...................................................4-5

Kit Assembly

–ISO DIN radio provision with pocket ..................6

–ISO DDIN radio provision .....................................7

Axxess Interface Installation .................................8

Final Assembly ...................................................... 11

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess interface included

Antenna Adapter: Included with kit

Steering wheel control interface: ASWC-1 included

A B C

D E

Cadillac XLR 2004-2009

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (13 pages)

PAGE 1
99-3030B I N S TA L L AT I O N I N S T R U C T I O N S Cadillac XLR 2004-2009 Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. On the bottom of the shifter, pull the chrome trim downward, and then remove (1) screw exposed. Pull up on the shifter to remove it. (Figure A) 2. Unclip the shifter trim plate, then set to the side. (Figure B) Continued on the next page (Figure A) 2 (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 3
DASH DISASSEMBLY (CONT.) 3. Unclip, unplug, and remove the radio/ climate control panel. (Figure C) 4. Remove (4) 9/32” screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure D) Continue to Kit Preparation (Figure C) (Figure D) REV.
PAGE 4
KIT PREPARATION From the factory radio/climate control panel: 1. Unclip and remove the a/c vents. (Figure A) 2. Unclip and remove the hazard switch. (Figure A) 3. Remove (4) screws securing the climate controls, then remove the controls. (Figure A) Continued on the next page (Figure A) 4 1.800.221.0932 | MetraOnline.
PAGE 5
KIT PREPARATION (CONT.) 4. Secure the appropriate climate control trim panel to the 99-3030B radio/ climate control panel using the (4) #8 x 3/8” Phillips screws provided. The climate control panel part number is stamped onto the back of the panel. CH-3030-1 - 2004-2005 CH-3030-2 - 2006-2009 (Figure A) To the 99-3030B radio/climate control panel: 5. Secure the (6) panel clips supplied to the panel (the factory clips can also be used if so desired). (Figure B) (Figure A) (Figure B) (Figure C) 6.
PAGE 6
KIT ASSEMBLY ISO DIN radio provision with pocket 1. Secure the radio brackets to the pocket using the (4) #8 x 3/8” Phillips screws provided. (Figure A) 2. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3. Slide the radio into the bracket/pocket assembly, then secure it to the assembly using the screws supplied with the radio. (Figure B) Continue to Axxess Interface Installation (Figure A) 6 (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 7
KIT ASSEMBLY ISO DDIN radio provision 1. Secure the radio brackets to the radio using the screws supplied with the radio. (Figure A) Continue to Axxess Interface Installation (Figure A) REV.
PAGE 8
AXXESS INTERFACE INSTALLATION 8 INTERFACE FEATURES • Provides accessory power (12-volt 10-amp) • Maintains the Retained Accessory Power (R.A.P.) feature • Provides NAV outputs (parking brake, reverse, speed sense) • Retains warning chimes • Retains OnStar/OE Bluetooth • Adjustable volume for chimes and OnStar • Retains steering wheel controls via ASWC-1 • Retains the factory amplifier • Retains balance and fade • Micro-B USB updatable TABLE OF CONTENTS Connections.........................................
PAGE 9
CONNECTIONS From the 16-pin harness with stripped leads to the aftermarket radio: • Connect the Red wire to the accessory wire. Note: There will be a Red wire from the 3030 harness to connect as well. • Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier. • If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is not connected, the radio will turn off when OnStar is activated.
PAGE 10
INSTALLATION With the key in the off position: 1. Connect the CD player jumper harness to the wiring harness in the vehicle. 2. Connect the ASWC-1 harness to the wiring harness in the vehicle. Do not connect the ASWC-1 until the Axxess interface is programmed and fully functional. 3. Connect the 16-pin harness with stripped leads into the Axxess interface. 4. Connect the 3030 harness into the Axxess interface, and then to the wiring harness in the vehicle. 5.
PAGE 11
ADJUSTMENTS FINAL ASSEMBLY Audio level adjustment: 1. Secure the radio assembly to the dash using the factory screws. 1. With the vehicle and radio turned on, turn the volume up 3/4 of the way. 2. Reassemble the dash in reverse order of disassembly using the 99-3030 radio trim panel to complete the installation. 2. With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise the audio level; counterclockwise to lower the audio level. 3.
PAGE 12
99-3030B I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.
PAGE 13
99-3030B Cadillac XLR 2004-2009 Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications D ISO DDIN radio provision S ISO DIN radio provision with pocket P Painted matte black The complete center dash panel is painted matte black for a factory look. Includes an Axxess interface, wiring harness, ASWC-1, and antenna adapter for a complete installation.