User Manual

ManualsBrandsMetra Manualschassis components99-2007

METRA. THE WORLD’S BEST KITS.™

APPLICATIONS

1-800-221-0932

metraonline.com

INSTALLATION INSTRUCTIONS FOR PART 99-2007

WIRING & ANTENNA CONNECTIONS (Sold Separately)

Wiring Harness: • GMOS-LAN-05 GM LAN digital amp interface 2007-up

Antenna Adapter: • 40-CR10 Chrysler/GM antenna adapter 2002-up

Small Flat Blade Screwdriver • Panel Removal Tool • Phillips Screwdriver • Socket Wrench

TOOLS REQUIRED

2007-up Cadillac Escalade

99-2007

• A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets • D) Pocket

• E) 4) #8 3/8” Screws

KIT FEATURES

KIT COMPONENTS

• DIN radio provision with pocket

• ISO radio provision with pocket

• Double DIN radio provision

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-2007 APPLICATIONS 2007-up Cadillac Escalade 99-2007 KIT FEATURES • DIN radio provision with pocket • ISO radio provision with pocket • Double DIN radio provision KIT COMPONENTS • A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets • D) Pocket • E) 4) #8 3/8” Screws A B C D S S E S WIRING & ANTENNA CONNECTIONS (Sold Separately) Wiring Harness: • GMOS-LAN-05 GM LAN digital amp interface 2007-up Antenna Adapter: • 40-CR10 Chrysler/GM ante
PAGE 2
99-2007 Table of Contents Dash Disassembly – Cadillac Escalade 2007-up 3-4 Kit Assembly – Kit preparation – ISO DIN head unit provision – Double DIN head unit provision 5 6-7 8 Caution Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. *NOTE: Refer also to the instructions included with the aftermarket radio.
PAGE 3
99-2007 Dash Disassembly 1. Unclip and remove cup holder and ashtray assembly. (Figure A) 2. Unclip and remove the trim panel above the glove box including the a/c vent. (Figure B) 3. Unclip and remove the entire panel surrounding the radio including the a/c vents.
PAGE 4
99-2007 Dash Disassembly 4. Remove (6) 9/32” screws to extract radio from dash.
PAGE 5
Kit Assembly 99-2007 Kit Preparation 1. Cut and remove the shaded areas marked with an “S” only from the radio housing. (Figure A) Right side and top of radio housing. (Figure B) Left side and top of radio housing. S S NOTE: DO NOT remove the tab marked with both “S” and “E”. Continue to kit assembly.
PAGE 6
Kit Assembly 99-2007 ISO mount radio provision with pocket 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Flip the radio housing brackets upside down then snap them to the inside edge of the radio housing. (Figure A) 3.
PAGE 7
Kit Assembly 99-2007 ISO mount radio provision with pocket 5. Snap the radio housing trim plate onto the front of the radio housing. (Figure D) 6. Reassemble dash in reverse order of disassembly.
PAGE 8
Kit Assembly 99-2007 Double DIN radio provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Attach the radio housing brackets to the inside edge of the radio housing. (Figure A) 3. Slide the double DIN radio into the radio housing bracket assembly and secure the unit using the screws supplied with the radio. (Figure B) (Figure A) 4.
PAGE 9
Notes
PAGE 10
Notes
PAGE 11
Notes
PAGE 12
REV. 6/13/11 INSTALLATION INSTRUCTIONS FOR PART 99-2007 METRA. THE WORLD’S BEST KITS.™ metraonline.