Owner's Manual

ManualsBrandsMetra ManualsOtherMetra 99-2005 Cadillac Sev/Dev/Eldo 96-05 Dash Kit

Table Of Contents

Installation Instructions

METRA. THE WORLD’S BEST KITS.™

APPLICATIONS

1-800-221-0932

metraonline.com

INSTALLATION INSTRUCTIONS FOR PART 99-2005

REV. 11/20/17

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness:

• GMRC-03 - Cadillac harness with chime 1996-2002

• GMOS-06 - Cadillac OnStar harness 2000-2005

Antenna Adapter:

• 40-GM10 - GM factory antenna to aftermarket

radio 1988-2006

• Small flat blade screwdriver • Panel removal tool • Phillips screwdriver • Socket wrench

TOOLS REQUIRED

Cadillac 1996-2005

99-2005

• A) Radio housing • B) Radio housing brackets • C) ISO brackets • D) ISO trim plate

• E) Spacer • F) (4) Phillips screws

KIT FEATURES

KIT COMPONENTS

B CA

• DIN mount radio provision with pocket

• ISO mount radio provision with pocket

98-04S

S-E

U.S. PATENT # D517,061

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-2005 APPLICATIONS Cadillac 1996-2005 99-2005 U.S.
PAGE 2
99-2005 Table of Contents Dash Disassembly – Cadillac Eldorado 1996-2002....................................................................................... 3-4 – Cadillac Seville 1996-1997........................................................................................... 3-4 – Cadillac Seville 1998-2005...............................................................................................5 – Cadillac DeVille 2000-2005......................................................................
PAGE 3
Dash Disassembly 99-2005 Cadillac Eldorado 1996-2002 Seville 1996-1997 1. Remove C-clip on forward facing side of shift knob and pull and remove knob. (Figure A) 2. Remove (2) 9/32” screws on each side of the ashtray assembly and (1) in the middle underneath ashtray insert. (Figure B) 3. Insert a small flat blade screwdriver in between the radio and the switch panel at top of radio and pry up and out to remove switch panel.
PAGE 4
Dash Disassembly 99-2005 Cadillac Eldorado 1996-2002 Seville 1996-1997 4. Remove (4) 9/32” screws, (2) from the top and (2) from the bottom, to remove radio. (Figure D, E) 5. Remove the (6) retaining nuts securing the radio and climate control to the factory bracket assembly and slide the climate control outward.
PAGE 5
Dash Disassembly 99-2005 Cadillac Seville 1998-2005/DeVille Concours (console shift) 1996-1999 1. Remove (2) 9/32 screws on each side of the ashtray assembly and (1) in the middle underneath ashtray insert. (Figure A) 2. Insert a small flat blade screwdriver in between the radio and the switch panel at top of radio and pry up and out to remove switch panel. (Figure B) (Figure B) 3. Remove (3) 9/32” screws, (1) from the top and (2) from the bottom to remove radio. (Figure C, D) 4.
PAGE 6
Dash Disassembly 99-2005 Cadillac Deville 2000-2005 1. Unsnap and remove panel surrounding climate controls and radio. (Figure A) 2. Depress clips on both sides of radio and pull out to remove.
PAGE 7
Kit Assembly 99-2005 Cadillac Eldorado 1996-2002 Cadillac Seville 1996-1997 1. Remove all tabs except the ones marked “S-E” from the radio housing. (Figure A) S-E D D 2. Slide the “S-E” radio housing bracket onto the 99-2005 until side clips engage. (Figure B) 98- 04 S 98- 04 S 98- 04 S S-E D 3. Slide the climate control assembly into the bracket/housing assembly and attach with the factory hardware.
PAGE 8
Kit Assembly 99-2005 Cadillac Seville 1998-2005/DeVille Concours (console shift) 1996-1999 Note: There is not enough depth to ISO mount or DIN mount without the spacer in the Deville 2000-2004. To mount the DIN you will need to use the provided spacer as described below. 1. Remove all tabs except the ones marked “98-04 S” from the radio housing. (Figure A) 2. Slide the “98-04 S” radio housing bracket onto the 99-2005 until side clips engage. (Figure B) (Figure B) 3.
PAGE 9
Kit Assembly 99-2005 Cadillac Deville 2000-2005 Note: There is not enough depth to ISO mount or DIN mount without the spacer in the Deville 2000-2004. To mount the DIN you will need to use the provided spacer as described below. S-E D D 1. Remove all tabs except the ones marked “D” from the radio housing. (Figure A) 98- 04 S 98- 04 S 98- 04 S S-E D D 2. When DIN mounting slide the included spacer onto the DIN cage that came with your aftermarket radio before inserting it into the housing.
PAGE 10
Kit Assembly 99-2005 DIN head unit provision 1. Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the after-market head unit into the cage and secure. (Figure B) 3. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 4. Reassemble dash in reverse order of disassembly.
PAGE 11
Kit Assembly 99-2005 ISO DIN head unit provision 1. Mount the ISO brackets to the aftermarket radio with the screws supplied with the unit. (Figure A) 2. Slide the after-market radio unit into the cage and secure. (Figure B) 3. Snap the Trim plate into the Radio Housing. (Figure B) 4. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. (Figure A) 5.
PAGE 12
REV. 11/20/17 INSTALLATION INSTRUCTIONS FOR PART 99-2005 METRA. THE WORLD’S BEST KITS.™ metraonline.