Installation Guide

ManualsBrandsMetra ManualsCar Electronics & GPSMetra - Dash Kit for Select Harley-Davidson Motorcycles - Black

INSTALLATION INSTRUCTIONS

95-970 1

The World’s best kits.

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DDIN radio provision*

• Designed for models without a radio option**

* This kit can only be used with an ISO DDIN radio that has an “L” shaped chassis

design, with the radio chassis at the top of the screen. At present only the Sony

XAV-AX100, XAV-AX200, and XAV-AX5000 radios have this design.

** For models with a radio option use 95-9700

KIT COMPONENTS

• A) Radio housing • B) Radio brackets • C) (8) #8 x 3/8” Phillips screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Torx screwdrivers • Allen wrenches

TABLE OF CONTENTS

Fairing Disassembly

– Harley Davidson Street Glide, Electra Glide,

Ultra, and Limited models 2014-up .............2-3

– Harley Davidson Road Glide 2015-up..............4

Kit Assembly ..........................................................5

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: Not applicable

Antenna Adapter:

Not applicable*

Steering wheel control interface:

Not applicable

* Use part number 40-UA20 to add an antenna

Harley-Davidson Street Glide, Electra Glide,

Ultra, and Limited models 2014-up /

Road Glide 2015-up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (16 pages)

PAGE 1
95-9701 I N S TA L L AT I O N I N S T R U C T I O N S Harley-Davidson Street Glide, Electra Glide, Ultra, and Limited models 2014-up / Road Glide 2015-up Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications KIT FEATURES • ISO DDIN radio provision* • Designed for models without a radio option** * This kit can only be used with an ISO DDIN radio that has an “L” shaped chassis design, with the radio chassis at the top of the screen.
PAGE 2
FAIRING DISASSEMBLY Harley Davidson Street Glide, Electra Glide, Ultra, and Limited models 2014-up 1. Remove (4) T-27 from inner fairing. (Figure A) 2. Remove (3) T-27 from windshield (caution not to drop the outer fairing or windshield). (Figure B) 3. Remove outer fairing, unplugging the headlight. (Figure C) 4. Remove (2) T-27 to remove the fairing vent and remove the vent. (Figure D) (Figure A) (Figure C) (Figure B) (Figure D) Continued on next page 2 1.800.221.0932 | MetraOnline.
PAGE 3
FAIRING DISASSEMBLY (CONT) 5. Remove (11) screws securing the radio bracket: (Figure E) a. (2) T-27 Torx screws shared with the gauge cluster and a third T-27 Torx screw to remove the gauge cluster in step 7. b. (4) 5/32” Allen screws facing outward. c. (4) T-25 Torx screws secured to the radio. d. (1) T-25 Torx screw shared with the storage pocket. 6. Remove the radio bracket. (Figure E) Note: This bracket will be reused in re-assembly. (Figure E) 7. Remove the gauge cluster. (Figure E) 8.
PAGE 4
FAIRING DISASSEMBLY (CONT) Harley Davidson Road Glide 2015-up 1. Remove the lower torx screws on either side holding the wind deflector wings (only the lower two need to be removed). (Figure A) 2. Remove (1) 3/16 Allen screw securing each turn signal. (Figure B) 7. Remove the fairing and set aside. 8. Remove (4) 3/16 Allen screws from the sides of the radio. (Figure A) Note: These screws will be reused in Kit Assembly. 3. Remove (4) Phillips screws from the windshield and set the windshield aside.
PAGE 5
KIT ASSEMBLY 1. Secure the radio brackets to the radio housing with (4) #8 x 3/8” Phillips screws supplied. (Figure A) 2. Slide the radio into the radio housing assembly and secure with screws supplied with the radio. (Figure B) 3. Secure the radio housing assembly to the bike using (4) 3/16 Allen screws previously removed in step 8 of disassembly. (Figure C) 4. a.
PAGE 6
1.800.221.0932 | MetraOnline.
PAGE 7
REV.
PAGE 8
95-9701 I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.
PAGE 9
5-9701 I N S T R U C C I O N E S D E I N S TA L AC I Ó N Harley-Davidson Street Glide, Electra Glide, Ultra, y Limited modelos 2014 y mas / Road Glide 2015 y mas Visite MetraOnline.com para obtener información más detallada sobre el producto y aplicaciones actualizadas específicas para vehículos.
PAGE 10
DESMONTAJE CARENADO Harley Davidson Street Glide, Electra Glide, Ultra, and Limited modelos 2014 y mas 1. Quite los (4) T-27 del carenado interior. (Figura A) 2. Quite los (3) T-27 del parabrisas (tenga cuidado de no dejar caer el carenado exterior o el parabrisas). (Figura B) 3. Quite el carenado exterior desconectando el faro. (Figura C) 4. Quite los (2) T-27 para quitar la rejilla del carenado y quite la rejilla.
PAGE 11
DESMONTAJE CARENADO (CONT) 5. Quite los (11) tornillos que sujetan el soporte del radio: (Figura E) a. (2) Tornillos Torx T-27 que se comparten con el conjunto de indicadores y un tercer tornillo Torx T-27 para quitar el conjunto de indicadores en el paso 7. b. (4) Tornillos Allen de 5/32” orientados hacia afuera. c. (4) T-25 Torx screws secured to the radio. d. (1) Tornillos Torx T-25 que se comparten con la cavidad de almacenamiento. 6. Quite el soporte del radio.
PAGE 12
DESMONTAJE CARENADO (CONT) Harley Davidson Road Glide 2015 y mas 1. Quite los tornillos Torx inferiores de cada lado que sostienen los deflectores de viento (solo deben quitarse los dos inferiores). (Figura A) 2. Quite el (1) tornillo Allen de 3/16” que sujeta cada señal direccional. (Figura B) 7. Quite el carenado y déjelo a un lado. 8. Quite los (4) tornillos Allen de 3/16 de los lados del radio. (Figura A) 4. Quite la moldura del carenado superior enganchada en la parte superior del radio.
PAGE 13
ENSAMBLE DEL KIT 1. Atornille los soportes del radio a la carcasa del radio con los (4) tornillos Phillips de cabeza plana suministrados. (Figura A) 2. Deslice el radio en el ensamble de la carcasa del radio y sujételo con los tornillos suministrados con el radio. (Figura B) 3. Asegurar el ensamble de radio a la bicicleta usando (4) 3/16 tornillos Allen eliminan previamente en el paso 8 de desmontaje. (Figura C) 4. a.
PAGE 14
6 1.800.221.0932 | MetraOnline.
PAGE 15
REV.
PAGE 16
95-9701 I N S T R U C C I O N E S D E I N S TA L AC I Ó N Si tiene dificultades con la instalación de este producto, comuníquese con nuestra línea de soporte técnico, ya sea por teléfono al 1-800-253-TECH, o envíe un correo electrónico a techsupport@metraautosound.com. Antes de hacerlo, revise el folleto de instrucciones por segunda vez y asegúrese de que la instalación se realizó exactamente como se indica en el manual de instrucciones.