Datasheet

ManualsBrandsMetra ManualsMobile Phones95-8204

INSTALLATION INSTRUCTIONS FOR PART 95-8204

95-8204

KIT FEATURES

• Double DIN Radio Provision

• Stacked ISO Units Provision

A) Double DIN Trim Plate B) Double DIN Brackets

KIT COMPONENTS

Small Flat Blade Screwdriver • Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932

TION

www.metr

aonline.com

TOOLS REQUIRED:

APPLICATIONS

Toyota Corolla

2003-2008

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-8204 APPLICATIONS Toyota Corolla 2003-2008 95-8204 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Units Provision KIT COMPONENTS A) Double DIN Trim Plate B) Double DIN Brackets A B TOOLS REQUIRED: Small Flat Blade Screwdriver • Panel Removal Tool • Phillips Screwdriver • Socket Set 1-800-221-0932 www.metraonline.
PAGE 2
95-8204 TABLE OF CONTENTS Dash Disassembly - Totota Corolla 2003-2008 . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Units Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
95-8204 DASH DISASSEMBLY TOYOTA COROLLA 2003-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the gear shifter trim panel. (Figure A) P R N D 3 Remove the center a/c knob and (1) Phillips screw exposed behind it. (Figure B) 2 L 4 Unclip and remove the a/c-pocket assembly. (Figure C) B 5 Remove (4) 10 MM bolts from the bottom of the radio then unclip and remove the factory radio and trim panel together. Unplug radio from factory harness.
PAGE 4
95-8204 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN trim plate into the factory trim panel. (Figure A) 2 Slide the Double DIN radio into the Double DIN brackets and secure the radio to the brackets using the screws supplied with the radio. (Figure B) Continue to final assembly.
PAGE 5
95-8204 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN trim plate into the factory trim panel. (Figure A) 2 Slide the stacked ISO units into the Double DIN brackets and secure the units to the brackets using the screws supplied with the units. (Figure B) Continue to final assembly.
PAGE 6
95-8204 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 7
95-8204 NOTES 5
PAGE 8
95-8204 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.