Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installationDash Kit

REV. 4/6/2016 INST95-7811

INSTALLATION INSTRUCTIONS FOR PART 95-7811

METRA. The World’s best kits.

™

metraonline.com

CAUTION!

All accessories, switches, climate controls panels,

and especially air bag indicator lights must be connected before

cycling the ignition. Also, do not remove the factory radio with

the key in the on position, or while the vehicle is running.

• ISO DDIN radio provision

• 95-7811B - Painted matte black

• 95-7811HG - Painted gloss black

• A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8” Phillips screws

20;-,(;<9,:

20;*64765,5;:

>0905.(5;,55(*655,*;065: (sold separately)

Wiring Harness: • 70-1729

Antenna Adapter: • 40-HD11 • 40-HD12 (EX and higher)

• Panel removal tool • Phillips screwdriver

• 10mm socket wrench with extension

• E-12 reverse (external) Torx socket

;663:9,8<09,+

Honda Pilot 2016-up

95-7811

Table of Contents

Dash Disassembly ..............................................2-4

Kit Assembly .......................................................... 5

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-7811 Honda Pilot 2016-up 95-7811 Table of Contents Dash Disassembly ..............................................2-4 Kit Assembly .......................................................... 5 20; -,(;<9,: • ISO DDIN radio provision • 95-7811B - Painted matte black • 95-7811HG - Painted gloss black 20; *64765,5;: • A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8” Phillips screws REV.
PAGE 2
95-7811 Dash Disassembly 1. Open the passenger door and remove the dash trim on the side of the dash. (Figure A) 2. Open the glove box and remove the dash trim above the opening. (Figure B) 3. Open the driver’s door and remove the dash trim on the side of the dash.
PAGE 3
95-7811 Dash Disassembly 4. Unsnap and remove the panel under the steering wheel. (Figure D) 5. Unclip and remove the hazard/ airbag switch panel. (Figure E) 6. Remove (3) Phillips screws securing the climate control trim panel and then remove.
PAGE 4
95-7811 Dash Disassembly 7. Remove (2) Phillips screws securing the storage pocket and then remove. If equipped with a rear DVD player instead, remove (2) Phillips screws from the sides, and (2) E-12 reverse (external) Torx screws from the top, and then remove. (Figure G) 8. Remove the (2) upward facing 10mm bolts from the brackets on the bottom of the radio. (Figure H) 9. Unclip and remove the radio/vent assembly. (Figure I) (Figure G) (Figure H) 10.
PAGE 5
95-7811 Kit Assembly 1. Attach the clips removed in step 10 of dash disassembly to the same locations on the radio trim panel. 5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio and climate controls. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation. 2. Attach the radio brackets to the radio trim panel using the (4) #8 x 3/8” Phillips screws provided. (Figure A) 3.
PAGE 6
INSTALLATION INSTRUCTIONS FOR PART 95-7811 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.