Installation Guide

ManualsBrandsMetra ManualsCar Electronics & GPSDash Kit for Select Acura Vehicles - Charcoal Gray

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

95-7805CH

KIT FEATURES

• ISO DDIN radio provision

• Painted charcoal gray

KIT COMPONENTS

• A) Radio housing • B) Radio brackets • C) (4) #8 x 3/8” pan-head Phillips screws • D) (2) #8 x 1/2” truss-head Phillips screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Socket wrench

TABLE OF CONTENTS

Dash Disassembly .............................................. 2-5

Kit Assembly ..........................................................6

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-1729 • 70-1730

Antenna Adapter: 40-HD10 • 40-HD12

A B C D

Acura TSX (without NAV) 2009-2014

Summary of content (16 pages)

PAGE 1
95-7805CH I N S TA L L AT I O N I N S T R U C T I O N S Acura TSX (without NAV) 2009-2014 KIT FEATURES • ISO DDIN radio provision • Painted charcoal gray WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: 70-1729 • 70-1730 Antenna Adapter: 40-HD10 • 40-HD12 KIT COMPONENTS • A) Radio housing • B) Radio brackets • C) (4) #8 x 3/8” pan-head Phillips screws • D) (2) #8 x 1/2” truss-head Phillips screws A B C TABLE OF CONTENTS Dash Disassembly...............................................
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove the trim panel above the glove box on the passenger side of the dash. (Figure A) 3. Remove (2) Phillips screws securing the driver and passenger side trim panels, then unclip and remove the panels from the console. (Figure C and D) 2. Unclip and remove the shifter panel including the cup holders. (Figure B) 2 Continued on next page (Figure A) (Figure C) (Figure B) (Figure D) 1.800.221.0932 | MetraOnline.
PAGE 3
DASH DISASSEMBLY 4. Unclip and remove the coin holder from the 12 volt socket/coin holder assembly. (Figure E) (CONT.) 6. Remove (4) Phillips screws securing the pocket assembly then unclip and remove the pocket. (Figure G) 5. Remove (1) Phillips screw under coin holder then unclip and remove 12 volt socket/coin holder assembly. (Figure F) Continued on next page (Figure E) (Figure G) (Figure F) REV.
PAGE 4
DASH DISASSEMBLY (CONT.) 7. Remove (4) Phillips screws securing the climate control then unplug and remove the control. (Figure H) 8. Remove (2) Phillips screws facing up under factory radio. (Figure I) 9. Remove (2) Phillips screws securing the hazard switch. 10. Remove the (4) plastic clips from the factory radio assembly. Continued on next page (Figure H) 4 (Figure I) 1.800.221.0932 | MetraOnline.
PAGE 5
DASH DISASSEMBLY (CONT.) 10. Remove (2) Phillips screws per vent securing the a/c vents to the radio panel then unclip and remove the vents. (Figure J) Continue to Kit Assembly (Figure H) REV.
PAGE 6
KIT ASSEMBLY 5. Attach the hazard switch to the radio housing using the supplied (2) #8 x 1/2” truss-head Phillips screws. 1. Attach the (4) panel clips to the radio housing. (Figure A) 2. Attach the radio brackets to the radio housing using the supplied (4) #8 x 3/8” pan-head Phillips screws. (Figure B) 6. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the unit for proper operation. 3.
PAGE 7
REV.
PAGE 8
95-7805CH I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
PAGE 9
5-7805CH I N S T R U C C I O N E S D E I N S TA L AC I Ó N Acura TSX (sin NAV) 2009-2014 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN • Gris carbón pintado CABLEADO Y CONEXIONES DE ANTENAONS (se venden por separado) Arnés de cables: 70-1729 • 70-1730 Adaptador de antena: 40-HD10 • 40-HD12 COMPONENTES DEL KIT • A) Carcasa del radio • B) Soportes de carcasa del radio • C ) (4) tornillos Phillips de cabeza segmentada #8 x 3/8” • D) (4) tornillos Phillips de cabeza segmentada #8 x 1/2” A B C IN
PAGE 10
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel de moldura que está sobre la guantera del lado del pasajero en el tablero. (Figura A) 3. Quite (2) tornillos Phillips que sujetan los paneles de moldura del lado del conductor y del pasajero, luego desenganche los paneles de la consola. (Figura C y D) 2. Desenganche y quite el panel de la palanca de velocidades, incluyendo los portavasos. (Figura B) 2 Continúa en la página siguiente (Figura A) (Figura C) (Figura B) (Figura D) 1.800.221.
PAGE 11
DESMONTAJE DEL TABLERO 4. Desenganche y quite el portamonedas del ensamble del tomacorriente de 12 voltios/portamonedas. (Figura E) (CONT.) 6. Quite los (4) tornillos Phillips que sujetan el ensamble de la cavidad, luego desenganche y quite la cavidad. (Figura G) 5. Quite (1) tornillo Phillips de abajo del portamonedas y luego desenganche y quite el ensamble del tomacorriente de 12 voltios/portamonedas. (Figura F) Continúa en la página siguiente (Figura E) (Figura G) (Figura F) REV.
PAGE 12
DESMONTAJE DEL TABLERO (CONT.) 7. Quite los (4) tornillos Phillips que sujetan el control de clima y luego desenganche y quite el control. (Figura H) 8. Quite los (2) tornillos Phillips orientados hacia arriba de debajo del radio de fábrica. (Figura I) 9. Quite los (2) tornillos Phillips que sujetan el interruptor de las luces intermitentes. 10. Quite los (4) ganchos de plástico del ensamble del radio de fábrica. Continúa en la página siguiente (Figura H) 4 (Figura I) 1.800.221.0932 | MetraOnline.
PAGE 13
DESMONTAJE DEL TABLERO (CONT.) 11. Quite los (2) tornillos Phillips que sujetan cada rejilla de aire acondicionado al panel del radio y luego desenganche y quite las rejillas. (Figura J) Continúe con el Ensamble del Kit (Figura H) REV.
PAGE 14
ENSAMBLE DEL KIT 5. Coloque el interruptor de las luces intermitentes en la carcasa del radio con los (2) tornillos Phillips de cabeza segmentada #8 x 1/2” suministrados. 1. Coloque los (4) ganchos del panel en la carcasa del radio. (Figura A) 2. Coloque los soportes de radio en la carcasa del radio usando los (4) tornillos Phillips de cabeza troncocónica #8 x 3/8” suministrados. (Figura B) 3.
PAGE 15
REV.
PAGE 16
95-7805CH I N S T R U C C I O N E S D E I N S TA L AC I Ó N IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.