Installation Guide

ManualsBrandsMetra ManualsCar Electronics & GPSDash Kit for Select 2020 and Later Nissan Titan Vehicles - High Gloss Black

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

95 -7639HG

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DDIN radio provision

• Painted high gloss to match factory ﬁnish

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8” Phillips screws

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 12mm socket wrench • T-20 Torx driver

TABLE OF CONTENTS

Dash Disassembly .............................................. 2-5

Kit Assembly ..........................................................6

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-7552

Antenna Adapter: 40-NI12

A B C

Nissan Titan 2020-Up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (16 pages)

PAGE 1
95-7639HG I N S TA L L AT I O N I N S T R U C T I O N S Nissan Titan 2020-Up Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications KIT FEATURES • ISO DDIN radio provision • Painted high gloss to match factory finish KIT COMPONENTS • A) Radio trim panel • B) Radio brackets • C) (4) #8 x 3/8” Phillips screws A B TABLE OF CONTENTS Dash Disassembly .............................................. 2-5 Kit Assembly ..................................
PAGE 2
DASH DISASSEMBLY 1. Remove the (2) Phillips screws securing the knee bolster panel below the steering column, and then unclip the panel. It is not necessary to completely remove the panel. (Figure A) Upper screws 2. Unclip and remove the passenger door sill and kick panel. (Figure B) 3. Remove the (5) Phillips screws securing the glove box and then remove. There are (2) screws below the glove box, and (3) screws exposed when you open the glove box.
PAGE 3
DASH DISASSEMBLY 4. Unclip and remove the (2) side trim panels at the front of the center console, and then remove the (1) Phillips screw exposed behind each panel. Tip: Pull out on the front sides of the console to release for later steps. (Figure E) 5. Slide both of the front seats forward and then remove the (2) 12mm bolts from the rear sides of the center console. Slide the seat back once done. (Figure F) 6.
PAGE 4
DASH DISASSEMBLY 7. Unclip and remove the trim panel where the center console and the dashboard meet, and then remove the (2) Phillips screws exposed. (Figure H) 8. Slide the center console back, and then unclip and remove the vent panels from each side of the radio/climate control panel. (Figure I) 9. Remove the (2) Phillips screws securing the accessory panel below the climate control panel, and then unclip and remove. (Figure J) (Figure H) (Figure I) (Figure J) Continued on next page 4 386.257.
PAGE 5
DASH DISASSEMBLY 10. Remove the (2) Phillips screws securing the climate control panel and then remove. (Figure K) 11. Remove the (4) Phillips screws securing the radio and then remove. (Figure L) 12. Slightly loosen the (8) T-20 Torx screws securing the radio brackets. Remove the (2) T-20 Torx screws securing the “white” climate control module below the radio and then remove. This module will be reused in kit assembly. (Figure M) (Figure K) Continue to Kit Assembly (Figure M) (Figure L) REV.
PAGE 6
KIT ASSEMBLY 1. Attach the radio brackets to the radio trim panel using the (4) #8 x 3/8” Phillips screws provided. (Figure A) 3. Slide the radio into the completed assembly, and then secure it to the assembly using the screws supplied with the radio. (Figure C) 2. Slide the “white” climate control module removed in dash disassembly into the lower portion of the bracket/panel assembly, and then secure with the factory hardware. (Figure B) (Figure A) 4.
PAGE 7
REV.
PAGE 8
95-7639HG I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 386-257-1187, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.
PAGE 9
5-7639HG I N S T R U C C I O N E S D E I N S TA L AC I Ó N Nissan Titan 2020 y Mas Visite MetraOnline.com para obtener información más detallada sobre el producto y aplicaciones actualizadas específicas para vehículos. CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN • Pintado de alto brillo para combinar con el acabado de fábrica COMPONENTES DEL KIT • A) Panel de la moldura del radio • B) Soportes del radio • C) (4) Tornillos Phillips #8 x 3/8” A B INDICE Desmontaje del tablero ................
PAGE 10
DESMONTAJE DEL TABLERO 1. Quite los (2) tornillos Phillips que sujetan el panel del protector de rodillas debajo de la columna de dirección, luego desenganche el panel. No es necesario quitar el panel por completo. (Figura A) Tornillos superiores 2. Desenganche y quite el apoyo de la puerta y el panel de protección. (Figura B) 3. Quite los (5) tornillos T-20 Torx que sujetan la caja de la guantera y luego quítela.
PAGE 11
DESMONTAJE DEL TABLERO 4. Desenganche y quite los (2) paneles de la moldura lateral en la parte frontal de la consola central, y luego quite (1) tornillo Phillips expuesto detrás de cada panel. Sugerencia: jale los lados frontales de la consola para liberar en pasos siguientes. (Figura E) 5. Deslice ambos asientos frontales hacia adelante y luego quite las (2) tuercas de 12 mm de los lados traseros de la consola central. Deslice el asiento hacia atrás cuando haya terminado.
PAGE 12
DESMONTAJE DEL TABLERO 7. Desenganche y quite el panel de la moldura donde se unen la consola central y el tablero, y luego quite los (2) tornillos Phillips expuestos. (Figura H) 8. Deslice de vuelta la consola central y luego desenganche y quite los paneles de la rejilla de cada lado del panel de control del radio/clima. (Figura I) 9. Quite los (2) tornillos Phillips que sujetan el panel de accesorios debajo del panel de control del clima, y después desenganche y quite la cavidad.
PAGE 13
DESMONTAJE DEL TABLERO 10. Quite los (2) tornillos Phillips que sujetan el panel de control del clima y quite. (Figura K) 11. Quite los (4) tornillos Phillips que sujetan el radio y quite. (Figura L) 12. Afloje ligeramente los (8) tornillos Torx T-20 que sujetan los soportes del radio. Quite los (2) tornillos Torx T-20 que sujetan el módulo del control de clima “blanco” debajo del radio y retire. Este módulo se reutilizará en el ensamble del kit.
PAGE 14
ENSAMBLE DEL KIT 1. Una los soportes del radio al panel de la moldura del radio con los (4) tornillos Phillips #8 de 3/8” suministrados. (Figura A) 4. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Pruebe el radio para verificar si funciona bien. 2.
PAGE 15
REV.
PAGE 16
95-7639HG I N S T R U C C I O N E S D E I N S TA L AC I Ó N Si tiene dificultades con la instalación de este producto, comuníquese con nuestra línea de soporte técnico, ya sea por teléfono al 386-257-1187, o envíe un correo electrónico a techsupport@metraautosound.com. Antes de hacerlo, revise el folleto de instrucciones por segunda vez y asegúrese de que la instalación se realizó exactamente como se indica en el manual de instrucciones.