User Manual

ManualsBrandsMetra ManualsCar Electronics & GPSMetra - Dash Kit for 2004-2006 Kia Amanti Vehicles - Black

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

95-7319

KIT FEATURES

• ISO DDIN radio provision

KIT COMPONENTS

• A) Radio housing • B) Radio brackets • C) A/C control brackets

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly

–ISO DDIN radio provision .....................................3

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-7301

Antenna Adapter: Not required

A B C

Kia Amanti 2004-2006

Summary of content (8 pages)

PAGE 1
95-7319 I N S TA L L AT I O N I N S T R U C T I O N S Kia Amanti 2004-2006 TABLE OF CONTENTS Dash Disassembly...................................................2 Kit Assembly –ISO DDIN radio provision......................................
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove panel surrounding shifter including cup holders. (Figure A) 2. Remove (2) Phillips screws at base of panel surrounding radio and a/c controls. (Figure B) ESP 3. Unclip and remove panel surrounding radio and a/c control. (Figure C) 4. Remove (6) Phillips screws securing radio and a/c control. (Figure D) 5. Remove (4) Phillips screws securing factory a/c control to bracket assembly.
PAGE 3
KIT ASSEMBLY ISO DDIN radio provision 1. Attach the corresponding a/c control brackets to the factory a/c control using the factory hardware. (Figure A) Note: The radio housing must be installed first before the a/c control. 2. Secure the radio brackets to the radio with screws supplied with the radio. (Figure B) 3. Slide the radio into the radio opening of the sub-dash. (Figure A) (Figure B) (Figure C) 4.
PAGE 4
95-7319 I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
PAGE 5
95-7319 I N S T R U C C I O N E S D E I N S TA L AC I Ó N Kia Amanti 2004-2006 INDICE Desmontaje del tablero.........................................2 Ensamble del kit – Provisión de radio ISO DDIN................................
PAGE 6
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel que rodea el cambiador incluyendo los portavasos. (Figura A) 2. Quite los (2) tornillos Phillips de la base del panel que rodea la radio y los controles de a/c. (Figura B) ESP 3. Desenganche y quite el panel que rodea la radio y los controles de a/c. (Figura C) 4. Quite (6) tornillos Phillips que aseguran la radio y el controls de a/c. (Figura D) 5. Quite (4) tornillos Phillips que aseguran el control de a/c de fábrica al ensamble del soporte.
PAGE 7
ENSAMBLE DEL KIT Provisión de radio ISO DDIN 1. Conecte los soportes de control de a/c correspondientes al control de a/c de fábrica usando el hardware de fábrica. (Figura A) Nota: La carcasa de la radio debe instalarse primero antes del control de a/c. 2. Coloque a presión los soportes de radio a la radio con los tornillos suministrados con la radio. (Figura B) (Figura A) (Figura B) (Figura C) 3. Deslice la radio en la abertura de la radio del sub tablero. 4.
PAGE 8
95-7319 I N S T R U C C I O N E S D E I N S TA L AC I Ó N IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.