Car Stereo System User Manual

ManualsBrandsMetra Electronics ManualsCar Stereo SystemCar Stereo System

INSTALLATION INSTRUCTIONS FOR PART 99-8902

99-8902

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

•A) Radio Housing • B) ISO Brackets • C) Trim Plate

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

SUBARU

Impreza2008-2011

Forester2009-11

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Wire harness:

• 70-7552 Nissan harness 2007-up

• 70-8901 Subaru harness 1990-up

Antenna adapter:

• 40-SB10 Subaru antenna adapter 2005-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-8902 APPLICATIONS SUBARU Impreza 2008-2011 Forester 2009-11 99-8902 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket KIT COMPONENTS •A) Radio Housing • B) ISO Brackets • C) Trim Plate B C WIRING AND ANTENNA CONNECTIONS (Sold Separately) Wire harness: • 70-7552 Nissan harness 2007-up • 70-8901 Subaru harness 1990-up Antenna adapter: • 40-SB10 Subaru antenna adapter 2005-up A TOOLS REQUIRED: Small Flat Blade Screwdriver/ Pan
PAGE 2
99-8902 TABLE OF CONTENTS Dash Disassembly - SUBARU Impreza 2008-2011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - SUBARU Forester 2009-2011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Final Assembly . . . . . . . . . .
PAGE 3
99-8902 DASH DISASSEMBLY SUBARU IMPREZA 2008-11/FORESTER 2009-11 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the factory radio including the a/c vents. (Figure A) 3 Remove (4) Phillips screws securing the radio. Unplug and remove the radio. (Figure B) Continue to kit assembly.
PAGE 4
99-8902 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly.
PAGE 5
99-8902 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly.
PAGE 6
99-8902 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 7
99-8902 NOTES 5
PAGE 8
99-8902 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.