Radio User Manual

ManualsBrandsMetra Electronics ManualsRadio99-7502

INSTALLATION INSTRUCTIONS FOR PART 99-7502

99-7502

APPLICATIONS

Mazda MPV 2000-2006

KIT FEATURES

• DIN Mount Radio Provision

• ISO Mount Radio Provision

A) Radio Housing • B) ISO Snap In Brackets • C) Trim Plate

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

TION

www.metr

aonline.com

TOOLS REQUIRED:

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7502 APPLICATIONS Mazda MPV 2000-2006 99-7502 KIT FEATURES • DIN Mount Radio Provision • ISO Mount Radio Provision KIT COMPONENTS A) Radio Housing • B) ISO Snap In Brackets • C) Trim Plate C B A TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver 1-800-221-0932 www.metraonline.
PAGE 2
99-7502 TABLE OF CONTENTS Dash Disassembly - Mazda MPV 2000-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio.
PAGE 3
99-7502 DASH DISASSEMBLY MAZDA MPV 2000-2006 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove (2) Phillips head screws from above instrument cluster. (Figure A) 3 Unclip and remove the radio trim panel. (Figure B) 4 Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure C) B Continue to kit assembly.
PAGE 4
99-7502 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly.
PAGE 5
99-7502 KIT ASSEMBLY ISO DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing assembly. (Figure B) Continue to final assembly.
PAGE 6
99-7502 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 7
99-7502 NOTES 5
PAGE 8
99-7502 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.